Valspar Ultra Interior Semi-Gloss Enamel No 391662 – Ultra White/Base A

Valspar Ultra Interior Semi-Gloss Enamel
No. 391662 – Ultra White/Base A
GENERAL DESCRIPTION
Valspar Ultra interior paint combines Paint +
Primer with superior quality color and features a
low odor, zero VOC formula.
PRODUCT FEATURES
• Superior-quality color
• Thick, one-coat coverage
• Stain resistant and scrubbable
• Gives a mildew-resistant finish
• Low odor
• 100^% acrylic latex for superior adhesion
• Lifetime warranty
RECOMMENDED USES
• Drywall
• Plaster
• Wood
• Primed Metal
• Brick
• Cement
SHIPPING AND PACKAGING
Freight Classification:
Paint or paint related material. Protect from
freezing.
UN #: NRPAIN
Packaging:
Quart, Gallon – 4 per carton
5-gallon pail
Case Weight: 42.3 lbs.
COMPOSITION
Base and Fill Levels
(oz./gal.)
Ultra White/Base A 128
Base B 120
Base C 116
APPLICATORS
Airless Spray:
Pressure: 2000 PSI
Tip: 0.017-0.019”
Brush: Premium quality polyester
Roller: Premium quality roller 3/8” nap
CLEANUP
Clean up with warm, soapy water.
SYSTEM
RECOMMENDATIONS
Drywall:
Self-priming
1-2 Coats: Ultra Interior Semi-Gloss Enamel
Plaster:
Self-priming
1-2 Coats: Ultra Interior Semi-Gloss Enamel
Wood:
Self-priming
1-2 Coats: Ultra Interior Semi-Gloss Enamel
Block:
1 Coat: Block Filler
1-2 Coats: Ultra Interior Semi-Gloss Enamel
Concrete/Masonry:
Self-priming
1-2 Coats: Ultra Interior Semi-Gloss Enamel
PRODUCT SPECIFICATIONS
Vehicle Type: Acrylic
Pigment Type: Titanium Dioxide
Viscosity: 97-103 Krebs Units
Gloss: 35-45 Units @ 60° angle
Flashpoint: 205 ˚F
VOC (g/L): 0 g/L*
VOC (lbs./gal.): 0
Volume Solids: 38%
Weight Solids: 50%
Weight Per Gallon: 10.85 lbs./gal.
Practical Coverage:
350-400 sq. ft./gal. (28-37 m 2 ) depending on
surface porosity
Recommended Film Thickness:
4.0 mil Wet 1.7 mil Dry
Dry Time @ 77° F and 50% Relative Humidity
To The Touch: 30-60 minutes
Recoat: 2-4 hours
Full Cure: 7 days
Application Temperature: 45-90 °F
Storage Temperature: 40˚-90 ˚F
Shelf Life: N/A
*This product contains 0 g/L VOC as calculated
within the margin of error by EPA Method 24.
CERTIFICATIONS
Current as of: 5/31/12
MPI # 54
MPI GPS 1
Yes
MPI GPS 2
Yes
LEED (US)
Yes
LEED (Canada)
N/A
REGULATORY COMPLIANCE
Current as of: 5/31/12
SCAQMD
CARB 2000 SCM
CARB 2007 SCM
OTC/LADCO
US National
Yes
Yes
Yes
Yes
Yes
The data on this sheet represents typical values. Since application variables are a major factor in product performance, this information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information.
UNLESS VALSPAR AGREES OTHERWISE IN WRITING, VALSPAR MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. VALSPAR WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this product, is the
replacement of the defective product, or a refund of its purchase price, at our option.

Valspar Ultra Interior Semi-Gloss Enamel
No. 391662 – Ultra White/Base A
SURFACE PREPARATION
Drywall:
Fill cracks, pits and voids with patching
compound, let dry and sand smooth. Joint
compounds must be cured and sanded smooth.
Remove all sanding dust.
Plaster:
Allow new plaster to fully cure and harden.
Surface should be free of dust.
Wood:
Sand wood smooth and patch holes and
imperfections with wood filer or putty and sand
smooth. Remove all sanding dust.
Block:
Masonry surfaces and mortar should be fully
cured, usually 30 days. Remove any loose
material or dust.
Concrete and Masonry:
New surfaces should be cured, usually 30 days.
Remove all form release or curing agents.
Surfaces should be free of loose material and
dust.
Mildew:
Remove mildew or suspected mildew by
scrubbing with a commercial mildew remover or
a solution of 1 part liquid chlorine bleach to 3
parts water. Allow solution to remain on surface
for 10 minutes. Rinse thoroughly with water and
allow surface to dry completely. Take precautions
to avoid contact with skin or eyes.
APPLICATION
Stir thoroughly and intermix multiple containers.
Apply product at temperatures ranging from 50-
90 °F. Apply with premium quality brush, roller or
spray application. Thinning is not recommended.
LEAD WARNING
WARNING! If you scrape, sand or remove old
paint, you may release lead dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN
CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with
a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your
family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on
to www.epa.gov/lead.
CAUTIONS
CAUTION. KEEP OUT OF THE REACH OF
CHILDREN. May cause eye and skin irritation. USE
ONLY WITH ADEQUATE VENTILATION. Avoid
breathing vapors, spray mist or sanding dust. If
painting indoors, open windows and doors or use
other means to ensure fresh air entry during
application and drying. If you experience eye
watering, headache or dizziness, or if air monitoring
demonstrates vapor/mist levels are above
applicable limits, wear an appropriate, properly fitted
respirator (NIOSH approved) during and after
application. Follow respirator manufacturer’s
directions for respirator use. When sanding, wear a
dust mask. AVOID CONTACT WITH THE EYES
AND SKIN. Wash thoroughly after use. Close
container after each use. DO NOT TAKE
INTERNALLY. FIRST AID: EYE CONTACT: Flush
thoroughly with water for at least 15 minutes. If
irritation persists, get medical attention.* IF
INHALED: If affected by vapor or spray mist, move
to fresh air. If breathing difficulty continues, get
medical attention.* IF SWALLOWED: Drink 2
glasses of water. Get medical attention
immediately.*
*Call poison control center, hospital emergency
room or physician immediately.
CL 1.3
Additional warning statement for the following
products: 391660, 391662, 391663, 391664:
WARNING! Contains Crystalline Silica, which can
cause cancer. Delayed effect from long-term
exposure: Cancer Hazard. Risk depends upon
duration and level of exposure to dust generated
from sanding surfaces or spray mist. WARNING:
This product contains a chemical known to the state
of California to cause cancer.
CL 3.3
For additional safety and chronic health
hazard information, refer to the Material
Safety Data Sheet for this product.
EMERGENCY MEDICAL TELEPHONE:
1-888-345-5732
This product contains 0 g/L VOC*
*This product contains 0 g/L VOC as calculated within the
margin of error by EPA Method 24.
1191 Wheeling Road, Wheeling, IL 60090
888.313.5569
valsparpaint.com
Revised: 5/31/12
Version: 391662A
The data on this sheet represents typical values. Since application variables are a major factor in product performance, this information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information.
UNLESS VALSPAR AGREES OTHERWISE IN WRITING, VALSPAR MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. VALSPAR WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this product, is the
replacement of the defective product, or a refund of its purchase price, at our option.