Valspar Ultra Exterior Semi-Gloss Paint No 19910 – White

Valspar Ultra Exterior Semi-Gloss Paint
No. 19910 – White
GENERAL DESCRIPTION
Valspar Ultra exterior paint combines Paint +
Primer with a superior-quality formula for the
ultimate weather defense.
PRODUCT FEATURES
• Exclusive acrylic stabilizers won’t peel or crack
• Superior-quality formula
• Durable one-coat coverage
• Superior fade resistance
• Gives a mildew-resistant finish
• Low odor, low VOC
• 100% acrylic latex for superior adhesion
• Lifetime warranty
RECOMMENDED USES
• Wood siding and trim
• Hardboard siding; fiber cement board
• Primed metal; weathered steel
• Shakes; asbestos shingles
• Brick; cement; cinder block
• Stucco; concrete; stone
• Aluminum and vinyl siding
SHIPPING AND PACKAGING
Freight classification:
Paint or paint related material. Protect from
freezing.
UN #: NRPAIN
Packaging:
Quart, Gallon – 4 per carton
5-gallon pail
Case weight: 44.7 lbs.
COMPOSITION
Base and Fill Levels
(oz./gal.)
White 128
Base 1 Tint Base 126
Base 2 Tint Base 124
Bass 4 Tint Base 116
APPLICATORS
Airless spray:
Pressure: 2000 PSI
Tip: 0.021
Brush: Premium-quality polyester
Roller: Premium-quality roller, 3/8–1/2 nap
CLEANUP
Clean up with warm, soapy water.
SYSTEM
RECOMMENDATIONS
Wood:
Self-priming
1–2 Coats: Ultra Exterior Semi-Gloss Paint
Block:
1 Coat: Block Filler
1–2 Coats: Ultra Exterior Semi-Gloss Paint
Concrete and masonry:
Self-priming
1–2 Coats: Ultra Exterior Semi-Gloss Paint
Galvanized metal and aluminum:
Self-priming
1–2 Coats: Ultra Exterior Semi-Gloss Paint
Ferrous metal:
1 Coat: Armor Anti-Rust Primer
1–2 Coats: Ultra Exterior Semi-Gloss Paint
Composition board/Hardboard:
Self-priming
1–2 Coats: Ultra Exterior Semi-Gloss Paint
Cement composition siding:
Self-priming
1–2 Coats: Ultra Exterior Semi-Gloss Paint
Vinyl siding:
Self-priming
2 Coats: Ultra Exterior Semi-Gloss Paint
Aluminum siding:
Self-priming
2 Coats: Ultra Exterior Semi-Gloss Paint
Stucco:
Self-priming
1–2 Coats: Ultra Exterior Semi-Gloss Paint
PRODUCT SPECIFICATIONS
Vehicle type: Acrylic
Pigment type: Titanium dioxide
Viscosity: 94–100 Kreb units
Gloss: 35–45 units @ 60° angle
Flashpoint: 205 °F
VOC (g/L): Less than 50 g/L
VOC (lbs./gal.): 0.39
Volume solids: 37%
Weight solids: 48%
Weight per gallon: 10.3 lbs./gal.
Practical coverage:
350–400 sq. ft./gal. (28-37 m 2 ) depending on
surface porosity
Recommended film thickness:
4.0 mil Wet 1.7 mil Dry
Dry time @ 77 °F and 50% relative humidity
To the touch: 1 hour
Recoat: 4 hours
Full cure: 7 days
Application temperature: 50–90 °F
Storage temperature: 40°–90 °F
Shelf life: N/A
CERTIFICATIONS
Current as of: 6/1/12
MPI # 11
MPI GPS 1
Yes
MPI GPS 2
Yes
LEED (US)
N/A
LEED (Canada)
N/A
REGULATORY COMPLIANCE
Current as of: 6/1/12
SCAQMD
CARB 2000 SCM
CARB 2007 SCM
OTC/LADCO
US National
Yes
Yes
Yes
Yes
Yes
The data on this sheet represents typical values. Since application variables are a major factor in product performance, this information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information.
UNLESS VALSPAR AGREES OTHERWISE IN WRITING, VALSPAR MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. VALSPAR WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this product, is the
replacement of the defective product, or a refund of its purchase price, at our option.

Valspar Ultra Exterior Semi-Gloss Paint
No. 19910 – White
SURFACE PREPARATION
Wood:
Spot prime pine knots with bonding primer or
exterior oil primer. Countersink nails and prime
entire wood surface with exterior latex primer.
Slight discoloration over cedar and redwood is
typical. Apply a second coat of primer if
discoloration is extreme. Caulk with acrylic caulk
before top coating.
Block:
New masonry surfaces and mortar should be
fully cured, usually 30 days. Remove any loose
material or dust. Fill concrete block with acrylic
block filler and allow to dry. Aged block should be
powerwashed or scrubbed to remove loose
concrete, laitance, efflorescence, mildew, dirt and
dust. Allow surface to dry thoroughly.
Concrete and masonry:
New surfaces should be cured, usually 30 days.
Remove all form release or curing agents.
Surfaces should be free of loose material and
dust.
Mildew:
Remove mildew or suspected mildew by
scrubbing with a commercial mildew remover or
a solution of 1 part liquid chlorine bleach to 3
parts water. Allow solution to remain on surface
for 10 minutes. Rinse thoroughly with water and
allow surface to dry completely. Take precautions
to avoid contact with skin or eyes.
Galvanized metal and aluminum:
Allow new galvanized metal to age 6 months or
clean with mild muriatic solution. Metal should be
free of oils and other contaminants.
Ferrous metal (steel and iron):
Hand or power-tool clean surfaces to remove oils
and other contaminants, mill scale and rust.
Prime with Armor Anti-Rust Primer.
Composition board/Hardboard:
Surface should be dry and free of dust,
contaminants and wax bleed through. Prime
entire surface and edges with exterior oil primer.
Caulk with an acrylic caulk before top coating.
SURFACE PREPARATION
Cement composition siding:
Surface should be dry and free of dust and
contaminants. Prime entire surface and edges
with exterior latex primer. Caulk with an acrylic
caulk before top coating.
Vinyl siding/Aluminum siding:
Surface should be clean, dry and free of
contaminants. Powerwash to remove chalk and
mildew.
Stucco:
Powerwash or scrub surface, with appropriate
cleaners, to remove loose material,
efflorescence, chalk and mildew. New stucco
should be allowed to cure and pH should be
below 10.
APPLICATION
Paint only when air or surface temperatures are
between 50 °F–90°F. Do not paint if
temperatures are expected to be below 50 °F
within 48 hours after application or when heavy
dew or precipitation is expected in the next 12
hours. Stir paint well and intermix containers of
the same color. Start at the highest point of the
house and work across. Always paint back into
freshly painted areas and end up at a door,
window or outer edge. Move windows after 1
hour to prevent sticking.
LEAD WARNING
WARNING! If you scrape, sand or remove old
paint, you may release lead dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN
CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with
a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your
family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on
to www.epa.gov/lead.
CAUTIONS
WARNING! Contains Crystalline Silica. KEEP OUT
OF THE REACH OF CHILDREN. May cause eye
and skin irritation. USE ONLY WITH ADEQUATE
VENTILATION. Avoid breathing vapors, spray mist
or sanding dust. If painting indoors, open windows
and doors or use other means to ensure fresh air
entry during application and drying. If you
experience eye watering, headache or dizziness, or
if air monitoring demonstrates vapor/mist levels are
above applicable limits, wear an appropriate,
properly fitted respirator (NIOSH approved) during
and after application. Follow respirator
manufacturer’s directions for respirator use. When
sanding, wear a dust mask. AVOID CONTACT
WITH THE EYES AND SKIN. Wash thoroughly after
use. Close container after each use. DO NOT TAKE
INTERNALLY. Delayed effect from long-term
exposure: Cancer Hazard. Contains crystalline
silica, which can cause cancer. Risk depends upon
duration and level of exposure to dust generated
from sanding surfaces or spray mist. WARNING:
This product contains a chemical known to the State
of California to cause cancer. FIRST AID: EYE
CONTACT: Flush thoroughly with water for at least
15 minutes. If irritation persists, get medical
attention.* IF INHALED: If affected by vapor or spray
mist, move to fresh air. If breathing difficulty
continues, get medical attention.* IF SWALLOWED:
Drink 2 glasses of water. Get medical attention
immediately.*
*Call poison control center, hospital emergency
room or physician immediately.
CL 3.3
For additional safety and chronic health hazard
information, refer to the Material Safety Data
Sheet for this product.
EMERGENCY MEDICAL TELEPHONE:
1-888-345-5732
This product contains less than 50 g/L VOC
1191 Wheeling Road, Wheeling, IL 60090
1.888.313.5569
valsparpaint.com
Revised: 6/1/12
Version: 19910G
The data on this sheet represents typical values. Since application variables are a major factor in product performance, this information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information.
UNLESS VALSPAR AGREES OTHERWISE IN WRITING, VALSPAR MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. VALSPAR WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this product, is the
replacement of the defective product, or a refund of its purchase price, at our option.