Valspar Duramax Exterior Latex Satin Paint No 75281 – White

Valspar ® Duramax ® Exterior Latex Satin Paint
No. 75281 – White
SURFACE PREPARATION
Wood:
Spot prime pine knots with Bonding Primer or
Exterior Oil Primer. Countersink nails and prime
entire wood surface with Exterior Latex Primer.
Slight discoloration over cedar and redwood is
typical. Apply a second coat of primer if
discoloration is extreme. Caulk with Acrylic caulk
before topcoating.
Block:
New masonry surfaces and mortar should be
fully cured, usually 30 days. Remove any loose
material or dust. Fill concrete block with Acrylic
Block Filler and allow to dry. Aged block should
be powerwashed or scrubbed to remove loose
concrete, laitance, efflorescence, mildew, dirt and
dust. Allow surfaces to dry thoroughly.
Concrete and Masonry:
New surfaces should be cured, usually 30 days.
Remove all form release or curing agents.
Surfaces should be free of loose material and
dust.
Mildew:
Remove mildew or suspected mildew by
scrubbing with a commercial mildew remover or
a solution of 1 part liquid chlorine bleach to 3
parts water. Allow solution to remain on surface
for 10 minutes. Rinse thoroughly with water and
allow surface to dry completely. Take
precautions to avoid contact with skin or eyes.
Galvanized Metal and Aluminum:
Allow new galvanized metal to age six months or
clean with mild muriatic acid solution. Metal
should be free of oils and other contaminants.
Ferrous Metal (Steel and Iron):
Hand or power tool clean surfaces to remove oils
and other contaminants, mill scale and rust.
Prime with Armor Anti-Rust Primer.
Composition Board/Hardboard:
Surface should be dry and free of dust,
contaminants and wax bleed-through. Prime
entire surface and edges with Bonding Primer.
Caulk with an acrylic caulk before topcoating.
SURFACE PREPARATION
Cement Composition Siding:
Surface should be dry and free of dust and
contaminants. Prime entire surface and edges
with Bonding Primer. Caulk with an acrylic caulk
before topcoating.
Vinyl Siding/Aluminum Siding:
Surface should be clean, dry and free of
contaminants. Power wash to remove chalk and
mildew.
Stucco:
Powerwash or scrub surface, with appropriate
cleaners, to remove loose material,
efflorescence, chalk and mildew. New stucco
should be allowed to cure and pH should be
below 10.
APPLICATION
Paint only when air and surface temperatures are
between 35-90 °F. Do not paint if temperatures
are expected to be below 35 ˚F within 48 hours
after application or when heavy dew or
precipitation is expected in the next 12 hours.
Stir paint well and intermix containers of the
same color. Start at the highest point of the
house and work across. Always paint back into
freshly painted areas and end up at a door,
window or outer edge. Move windows after one
hour to prevent sticking.
LEAD WARNING
WARNING! If you scrape, sand or remove old
paint, you may release lead dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN
CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with
a HEPA vacuum and a wet mop. Before you
start, find out how to protect yourself and your
family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on
to www.epa.gov/lead.
CAUTIONS
WARNING! Contains Crystalline Silica. KEEP OUT OF
THE REACH OF CHILDREN. May cause eye and skin
irritation. USE ONLY WITH ADEQUATE
VENTILATION. Avoid breathing vapors, spray mist or
sanding dust. If painting indoors, open windows and
doors or use other means to ensure fresh air entry
during application and drying. If you experience eye
watering, headache or dizziness, or if air monitoring
demonstrates vapor/mist levels are above applicable
limits, wear an appropriate, properly fitted respirator
(NIOSH approved) during and after application. Follow
respirator manufacturer’s directions for respirator use.
When sanding, wear a dust mask. AVOID CONTACT
WITH THE EYES AND SKIN. Wash thoroughly after
use. Close container after each use. DO NOT TAKE
INTERNALLY. Delayed effect from long-term exposure:
Cancer Hazard. Contains crystalline silica, which can
cause cancer. Risk depends upon duration and level of
exposure to dust generated from sanding surfaces or
spray mist. WARNING: This product contains
chemicals known to the State of California to cause
cancer. FIRST AID: EYE CONTACT: Flush thoroughly
with water for at least 15 minutes. If irritation persists,
get medical attention.* IF INHALED: If affected by
vapor or spray mist, move to fresh air. If breathing
difficulty continues, get medical attention.* IF
SWALLOWED: Drink 2 glasses of water. Get medical
attention immediately.*
*Call poison control center, hospital emergency room or
physician immediately.
CL 3.3s
Additional warning statement for the following
products: 75281, 34718
WARNING! Contains Ethylene Glycol and
Crystalline Silica. Harmful if swallowed. Vapor
Harmful.
For additional safety and chronic health
hazard information, refer to the Material
Safety Data Sheet for this product.
EMERGENCY MEDICAL TELEPHONE:
1-888-345-5732
CL 13.3s
This product contains less than 50 g/L VOC
1191 Wheeling Road, Wheeling, IL 60090
888.313.5569
www.valsparpaint.com
Revised: 9/18/12
Version:75281E
The data on this sheet represents typical values. Since application variables are a major factor in product performance, this information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information.
UNLESS VALSPAR AGREES OTHERWISE IN WRITING, VALSPAR MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. VALSPAR WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this product, is the
replacement of the defective product, or a refund of its purchase price, at our option.