- Page 1: Gear Cutting Tools • Hobbing •
- Page 4 and 5: Important information Product range
- Page 9 and 10: Hobs for spur gears, straight- or h
- Page 11 and 12: Notes to the descriptions and size
- Page 13 and 14: Solid-type hobs for spur and helica
- Page 15 and 16: Solid-type hobs for spur and helica
- Page 17 and 18: Hobs For economical production on m
- Page 19 and 20: Multiple-gash hobs 19
- Page 21 and 22: In order to achieve a high tool lif
- Page 23 and 24: Gear quality The gear quality is de
- Page 25 and 26: Multiple-gash hobs Recommended stru
- Page 27 and 28: Carbide types and coatings The carb
- Page 29 and 30: High-speed cutting (HSC) The advant
- Page 31 and 32: Size table for solid carbide hobs R
- Page 33 and 34: These requirements are met perfectl
- Page 35 and 36: Heavy duty roughing hobs (roughing
- Page 37 and 38: The rough hobbing of gears form mod
- Page 39 and 40: Roughing hobs with indexable carbid
- Page 41 and 42: A special position among the above
- Page 43 and 44: Pitch- and tooth trace deviations a
- Page 45 and 46: Skiving hobs with brazed-on carbide
- Page 47 and 48: Solid-type hobs for straight spur g
- Page 49 and 50: Hobs for internal gears, with strai
- Page 51: Solid-type hobs for internal gears
- Page 54 and 55: Hobs for compressor rotors Rotors a
- Page 56 and 57:
Rotor hobs, for finishing for screw
- Page 59 and 60:
Hobs for sprockets, timing belt pul
- Page 61 and 62:
Hobs for sprockets for Gall’s cha
- Page 63 and 64:
Hobs for sprockets with involute fl
- Page 65 and 66:
Hobs for timing belt pulleys with i
- Page 67 and 68:
Hobs for spline shafts quality grad
- Page 69 and 70:
Hobs for p.t.o. shafts to DIN 9611
- Page 71 and 72:
Hobs for spline shafts with involut
- Page 73:
73
- Page 76 and 77:
Hobs for worm gears The specificati
- Page 78 and 79:
Tangential method This method is su
- Page 80 and 81:
Engagement area and bearing contact
- Page 83 and 84:
Hobs for special profiles Hobs for
- Page 85:
. Multi-start single-position fly-c
- Page 88 and 89:
Worm thread milling cutters for mod
- Page 90 and 91:
Worm milling cutters for roughing f
- Page 92 and 93:
Rack milling cutters/worm milling c
- Page 94 and 95:
High-precision rack tooth gang cutt
- Page 97 and 98:
Gear milling cutters for spur gears
- Page 99 and 100:
Involute gear cutters for spur gear
- Page 101 and 102:
FETTE has considerable experience i
- Page 103 and 104:
End mill type gear cutters (finishi
- Page 105 and 106:
Gear roughing cutters with indexabl
- Page 107:
Gear finishing cutter ■ With carb
- Page 110 and 111:
Profile milling cutters for coarse-
- Page 112 and 113:
Rotor profile cutters for screw com
- Page 115 and 116:
Gear milling cutters for sprockets,
- Page 117 and 118:
Form milling cutters for timing bel
- Page 119 and 120:
Cat.-No. 2730 relief turned or reli
- Page 121 and 122:
Gear chamfering cutters for chamfer
- Page 123:
123
- Page 126 and 127:
Comparison: module pitch - diametra
- Page 128 and 129:
Tolerances for multiple start hobs
- Page 130 and 131:
Hob inspection records The toleranc
- Page 132 and 133:
The effect of cutter deviations and
- Page 134 and 135:
Effect of the quality grades of the
- Page 136 and 137:
Hob clamping Keyway Hob clamping Dr
- Page 138 and 139:
Basic profiles for spur gears with
- Page 140 and 141:
Basic hob profiles Defination of th
- Page 142 and 143:
Basic hob profiles to DIN 58412 Sym
- Page 144 and 145:
Profiles of current tooth systems a
- Page 146 and 147:
Sprocket tooth system for roller- a
- Page 148 and 149:
Spline shaft tooth system; basic cu
- Page 150 and 151:
"Carbide" is a generic term for pow
- Page 152 and 153:
The enormous increases in tool life
- Page 154 and 155:
Total a - Initial edge wear b - mec
- Page 156 and 157:
Cutting materials for hobs (See als
- Page 158 and 159:
A further a table of recommended va
- Page 160 and 161:
Number of starts of the hob With th
- Page 162 and 163:
Tool cutting edge length A distinct
- Page 164 and 165:
Tool cutting edge length (continued
- Page 166 and 167:
Shift distance The chip cross-secti
- Page 168 and 169:
Maintenance of hobs Introduction In
- Page 170 and 171:
Requirements placed upon the cuttin
- Page 172 and 173:
If the high or low points of the tw
- Page 174 and 175:
Hobs with a slightly concave cuttin
- Page 176 and 177:
Gash lead (item no. 11 DIN 3968) Th
- Page 178 and 179:
When regrinding, ensure that the co
- Page 180 and 181:
form circle diameter is less than t
- Page 182 and 183:
Wear phenomena on the hob The cutti
- Page 184 and 185:
Ziegler (2) demonstrated that the c
- Page 186 and 187:
The effect of the cutting condition
- Page 188 and 189:
the penetration line is important p
- Page 190 and 191:
left-hand start machines a gear wit
- Page 192 and 193:
Involute gear cutter with indexable
- Page 194 and 195:
DIN number index DIN Page 138 30, 4
- Page 196 and 197:
196