- Page 1: Gear Cutting Tools • Hobbing •
- Page 5 and 6: Grinding Services Services PVD-Coat
- Page 7: 7
- Page 10 and 11: Hobs for producing straight- and he
- Page 12 and 13: Topping cutters The outside diamete
- Page 14 and 15: Solid-type hobs for spur and helica
- Page 16 and 17: Solid-type hobs for spur and helica
- Page 18 and 19: Solid-type hobs for spur and helica
- Page 20 and 21: Coated solid-type hobs with a high
- Page 22 and 23: Shorter machining times The machini
- Page 24 and 25: Description of the workpiece: ■ M
- Page 26 and 27: Solid carbide hobs Introduction Car
- Page 28 and 29: Machining with and without coolant
- Page 30 and 31: Wear behavior Flank wear is the chi
- Page 32 and 33: Roughing hobs High cutting capaciti
- Page 34 and 35: Heavy duty roughing hobs (roughing
- Page 36 and 37: Roughing hobs with indexable carbid
- Page 38 and 39: The indexable carbide inserts must
- Page 40 and 41: Carbide skiving hobs Process and ra
- Page 42 and 43: Cutting conditions Cutting speed Th
- Page 44 and 45: Skiving hobs Solid carbide for fini
- Page 46 and 47: Skiving hobs with indexable carbide
- Page 48 and 49: 48
- Page 50 and 51: Explanatory notes Hobs for internal
- Page 53 and 54:
Hobs for compressor rotors and pump
- Page 55 and 56:
Rotor hobs, for roughing for screw
- Page 57:
Hobs for screw pumps for drive or t
- Page 60 and 61:
Hobs for sprockets to DIN 8196 for
- Page 62 and 63:
Hobs for sprockets for barrel chain
- Page 64 and 65:
Hobs for synchroflex timing belt pu
- Page 66 and 67:
Hobs for spline shafts quality grad
- Page 68 and 69:
Hobs for spline shafts quality grad
- Page 70 and 71:
Hobs for spline shafts with involut
- Page 72 and 73:
Hobs for serrated shafts to DIN 548
- Page 75 and 76:
Hobs for worm gears Hobs for worm g
- Page 77 and 78:
γ m α o generating line α o turn
- Page 79 and 80:
Shaving worms For high-precision wo
- Page 81:
Instructions for ordering: Worm gea
- Page 84 and 85:
Special and single-position hobs Th
- Page 87 and 88:
Gear milling cutters for racks and
- Page 89 and 90:
Rack and worm milling cutters modul
- Page 91 and 92:
Rack milling cutters/worm milling c
- Page 93 and 94:
Rack tooth gang cutters with severa
- Page 95:
95
- Page 98 and 99:
Involute gear cutters for spur gear
- Page 100 and 101:
Gear cutters for large-size gears T
- Page 102 and 103:
End mill type gear cutter (roughing
- Page 104 and 105:
Circular type gear roughing cutters
- Page 106 and 107:
Circular-type gear profile cutters
- Page 109 and 110:
Gear milling cutters for multi-star
- Page 111 and 112:
Roughing cutters for rotors with in
- Page 113:
113
- Page 116 and 117:
Form milling cutters for sprockets
- Page 118 and 119:
Form milling cutters for spline sha
- Page 120 and 121:
Form milling cutters for straight s
- Page 122 and 123:
Rolling racks FETTE manufacture rol
- Page 125 and 126:
Technical notes and tables Comparis
- Page 127 and 128:
Tolerances for single-start hobs fo
- Page 129 and 130:
For module range Item no. Measureme
- Page 131 and 132:
AAA it is usual to record the devia
- Page 133 and 134:
These relationships are shown in th
- Page 135 and 136:
Tool holding of hobs in the hobbing
- Page 137 and 138:
Basic tool profile and gear profile
- Page 139 and 140:
Standardized basic profiles for spu
- Page 141 and 142:
Basic hob profiles to DIN 3972 Symb
- Page 143 and 144:
ö fP0 14° 30' Basic hob profiles
- Page 145 and 146:
Involute tooth system, for spur- an
- Page 147 and 148:
Spline shaft tooth system; basic cu
- Page 149 and 150:
Cutting materials for hobs Hobs in
- Page 151 and 152:
Hard material coatings for gear cut
- Page 153 and 154:
Development of wear The cutting edg
- Page 155 and 156:
Cutting conditions in hobbing The c
- Page 157 and 158:
nomic tool life between successive
- Page 159 and 160:
Axial feed f a [mm/workpiece rotati
- Page 161 and 162:
Enveloping cut deviations Despite t
- Page 163 and 164:
Tool cutting edge length (continued
- Page 165 and 166:
Profile generating length Profile g
- Page 167 and 168:
Axial distance Axial distance in ho
- Page 169 and 170:
Since the wear curves cannot be det
- Page 171 and 172:
Hob tolerances The flank cutting ed
- Page 173 and 174:
A bigger rake angle (fig. 11) elong
- Page 175 and 176:
The measurement can also be carried
- Page 177 and 178:
Regrinding of roughing hobs FETTE r
- Page 179 and 180:
Protuberance hobs General principle
- Page 181 and 182:
Calculation of the root form circle
- Page 183 and 184:
These cutting force diagrams also r
- Page 185 and 186:
The cross-sectional areas of cut To
- Page 187 and 188:
The gear affects hob wear through i
- Page 189 and 190:
esults of the wear measurements on
- Page 191 and 192:
which can in the case of carbide le
- Page 193 and 194:
Catalogue number index Cat.-No. Pag
- Page 195 and 196:
195
- Page 197:
Fette GmbH Grabauer Str. 24 D-21493