simatic s7-300 - megaelektrik.net
simatic s7-300 - megaelektrik.net simatic s7-300 - megaelektrik.net
SIMATIC S7-300 Function modules FM 350-1 counter module ■ Overview • Single-channel intelligent counte r module for simple counting tasks • For direct connection of incremental encoders • Comparison function with 2 selectable comparison values • Integrated digital outputs to output the response upon reaching the comparison value. • Operating modes: - Continuous counting - One-shot counting - Periodic counting • Special functions; - Set counter - Latch counter • Start/stop counter with gate function 4 Note: SIMODRIVE Sensor/Motion Connect 500 feature incremental encoders and preassembled connecting cables for counting and positioning functions. Additional information is available in the Internet under: http://www.siemens.com/simatic-technology ■ Technical specifications 6ES7 350-1AH03-0AE0 Voltages and currents Auxiliary voltage 1L+, load voltage 2 L+ - Rated value (DC) 24 V • permissible range (including ripple) - dynamic, lower limit (DC) 18.5 V - dynamic, upper limit (DC) 30.2 V - static, lower limit (DC) 20.4 V - static, upper limit (DC) 28.8 V • Non-periodic snap-over - Duration 500 ms - Recovery time 50 s - Value 35 V Current consumption • from load voltage 1L+ 40 mA (no load), max. • from backplane bus 5 V DC, max. 160 mA • Power dissipation, typical 4.5 W Connection system • Requisite front connector 1 x 20-pin Digital inputs • Number of digital inputs 3 • Functions 1 for gate start, 1 for gate stop, 1 for setting the counter Input voltage - for signal "0" -28.8 to 5 V - for signal "1" +11 to +28.8 V Input current - for 1 signal, typical 9 mA 6ES7 350-1AH03-0AE0 Digital outputs • Number of digital outputs 2 • Short-circuit protection of the Yes; clocking electronically output • Limitation of voltage induced on 2L+ (-39 V) circuit interruption to Output voltage - for 0 signal (DC), max. 3 V - for 1 signal 2L+ (-1.5 V) Output current - for 1 signal rated value 0.5 A - for 1 signal permissible range 5 mA for 0 to 60 °C, min. - für Signal 1 zulässiger Bereich 0.6 A für 0 bis 60 °C, max. Output delay at resistive load - "0" to "1", max. 300 µs Sensor supply 5 V - sensor supply -5 V Yes; 5.2 V +/-2% - Output current, max. 300 mA 24 V - sensor supply - 24 V Yes; 1L+ (-3V) - Output current, max. 400 mA Sensor Connectable encoders - Incremental encoder Yes; with 2 pulse trains (symmetrical) offset by 90° - Incremental encoder Yes (asymmetrical) - 24 V initiator Yes - 24 V directional sensor Yes; 1 pulse train, 1 direction level Siemens ST 70 · 2005 4/93
SIMATIC S7-300 Function modules FM 350-1 counter module ■ Technical specifications (continued) 6ES7 350-1AH03-0AE0 6ES7 350-1AH03-0AE0 4 Counter • Number of counter inputs 1 • Counting range, description 32 Bit or +/-31 Bit • Minimum pulse width, adjustable Yes; 2.5 µs and 25 µs Counter input 5 V - Type RS 422 - Terminating resistance, approx. 220 Ω - Differential input voltage 1.3 V - Count frequency, max. 500 kHz Insulation • Insulation tested with Potentials/ electrical isolation Digital output functions - between the channels and the backplane bus Digital input functions - between the channels and the backplane bus 500 V Yes; Optocoupler Yes; Optocoupler Counter input 24 V - Input voltage, for 0 signal -28.8 to +5 V - Input voltage, for 1 signal +11 to +28.8 V - Input current, for 1 signal, typical 9 mA - Count frequency, max. 200 kHz - Minimum pulse width 2.5 µs Electrical isolation, counters - between the channels and the backplane bus Permissible potential difference • between different circuits Dimensions and weight Yes; Optocoupler 75 V DC/ 60 V AC • Weight, approx. 250 g • Width 40 mm • Height 125 mm •Depth 120 mm ■ Ordering data Order No. Order No. FM 350-1 counter module 6ES7 350-1AH03-0AE0 with 1 channel, max. 500 kHz; for incremental encoders Coding connector - range card 6ES7 974-0AA00-0AA0 for analog inputs Spare part Front connector 20-pin, with screw-type terminals •1 item 6ES7 392-1AJ00-0AA0 • 100 items 6ES7 392-1AJ00-1AB0 20-pin, with spring-loaded 6ES7 392-1BJ00-0AA0 terminals Bus connector 6ES7 390-0AA00-0AA0 1 unit (spare part) Labeling strips 6ES7 392-2XX00-0AA0 10 units (spare part) S7-SmartLabel 2XV9 450-1SL01-0YX0 Software for machine labeling of modules directly from the STEP 7 project Labeling sheets for machine see "Accessories" labeling Slot number label Spare part Shield connecting element 80 mm wide, with 2 rows for 4 terminal elements each Terminal elements 2 units For 2 cables with 2 to 6 mm diameter For 1 cable with 3 to 8 mm diameter For 1 cable with 4 to 13 mm diameter FM 350-1 manual German English French Italian Connectable incremental encoders 6FX2 001-2... 6ES7 912-0AA00-0AA0 6ES7 390-5AA00-0AA0 6ES7 390-5AB00-0AA0 6ES7 390-5BA00-0AA0 6ES7 390-5CA00-0AA0 6ES7 350-1AH00-8AG0 6ES7 350-1AH00-8BG0 6ES7 350-1AH00-8CG0 6ES7 350-1AH00-8EG0 Refer to A&D Mall under SIMO- DRIVE Sensor or Motion Connect 500 (see also www.siemens.com simatic-technology) 4/94 Siemens ST 70 · 2005
- Page 35 and 36: SIMATIC S7-300 Digital modules SM 3
- Page 37 and 38: SIMATIC S7-300 Digital modules SM 3
- Page 39 and 40: SIMATIC S7-300 Digital modules SM 3
- Page 41 and 42: SIMATIC S7-300 Digital modules SM 3
- Page 43 and 44: SIMATIC S7-300 Digital modules SM 3
- Page 45 and 46: SIMATIC S7-300 Digital modules SM 3
- Page 47 and 48: SIMATIC S7-300 Digital modules SM 3
- Page 49 and 50: 4 SIMATIC S7-300 SIPLUS digital mod
- Page 51 and 52: SIMATIC S7-300 SIPLUS digital modul
- Page 53 and 54: SIMATIC S7-300 Analog modules SM 33
- Page 55 and 56: SIMATIC S7-300 Analog modules SM 33
- Page 57 and 58: SIMATIC S7-300 Analog modules SM 33
- Page 59 and 60: SIMATIC S7-300 Analog modules SM 33
- Page 61 and 62: SIMATIC S7-300 Analog modules SM 33
- Page 63 and 64: 4 SIMATIC S7-300 Analog modules SM
- Page 65 and 66: 4 SIMATIC S7-300 Analog modules SM
- Page 67 and 68: SIMATIC S7-300 SIPLUS analog module
- Page 69 and 70: SIMATIC S7-300 SIPLUS analog module
- Page 71 and 72: SIMATIC S7-300 F digital / analog m
- Page 73 and 74: 4 SIMATIC S7-300 F digital / analog
- Page 75 and 76: 4 SIMATIC S7-300 F digital / analog
- Page 77 and 78: SIMATIC S7-300 SIPLUS F digital mod
- Page 79 and 80: 4 SIMATIC S7-300 Ex input / output
- Page 81 and 82: SIMATIC S7-300 Ex input / output mo
- Page 83 and 84: SIMATIC S7-300 Ex input / output mo
- Page 85: SIMATIC S7-300 Ex input / output mo
- Page 89 and 90: SIMATIC S7-300 Function modules FM
- Page 91 and 92: SIMATIC S7-300 Function modules FM
- Page 93 and 94: SIMATIC S7-300 Function modules FM
- Page 95 and 96: 4 SIMATIC S7-300 Function modules F
- Page 97 and 98: SIMATIC S7-300 Function modules FM
- Page 99 and 100: SIMATIC S7-300 Function modules FM
- Page 101 and 102: SIMATIC S7-300 Function modules FM
- Page 103 and 104: SIMATIC S7-300 Function modules FM
- Page 105 and 106: SIMATIC S7-300 Function modules 1FL
- Page 107 and 108: 4 SIMATIC S7-300 Function modules F
- Page 109 and 110: 4 SIMATIC S7-300 Function modules F
- Page 111 and 112: 4 SIMATIC S7-300 Function modules F
- Page 113 and 114: SIMATIC S7-300 Function modules SM
- Page 115 and 116: 4 SIMATIC S7-300 Function modules S
- Page 117 and 118: SIMATIC S7-300 Function modules SIW
- Page 119 and 120: SIMATIC S7-300 Function modules SIW
- Page 121 and 122: SIMATIC S7-300 IQ-Sense modules and
- Page 123 and 124: SIMATIC S7-300 IQ-Sense modules and
- Page 125 and 126: SIMATIC S7-300 Special modules SM 3
- Page 127 and 128: SIMATIC S7-300 Communication CP 340
- Page 129 and 130: SIMATIC S7-300 Communication SIPLUS
- Page 131 and 132: SIMATIC S7-300 Communication CP 341
- Page 133 and 134: SIMATIC S7-300 Communication CP 343
- Page 135 and 136: 4 SIMATIC S7-300 Communication CP 3
SIMATIC S7-<strong>300</strong><br />
Function modules<br />
FM 350-1 counter module<br />
■ Overview<br />
• Single-channel intelligent counte r module for simple counting<br />
tasks<br />
• For direct connection of incremental encoders<br />
• Comparison function with 2 selectable comparison values<br />
• Integrated digital outputs to output the response upon<br />
reaching the comparison value.<br />
• Operating modes:<br />
- Continuous counting<br />
- One-shot counting<br />
- Periodic counting<br />
• Special functions;<br />
- Set counter<br />
- Latch counter<br />
• Start/stop counter with gate function<br />
4<br />
Note:<br />
SIMODRIVE Sensor/Motion Connect 500 feature incremental<br />
encoders and preassembled connecting cables for counting<br />
and positioning functions.<br />
Additional information is available in the Inter<strong>net</strong> under:<br />
http://www.siemens.com/<strong>simatic</strong>-technology<br />
■ Technical specifications<br />
6ES7 350-1AH03-0AE0<br />
Voltages and currents<br />
Auxiliary voltage 1L+,<br />
load voltage 2 L+<br />
- Rated value (DC) 24 V<br />
• permissible range<br />
(including ripple)<br />
- dynamic, lower limit (DC) 18.5 V<br />
- dynamic, upper limit (DC) 30.2 V<br />
- static, lower limit (DC) 20.4 V<br />
- static, upper limit (DC) 28.8 V<br />
• Non-periodic snap-over<br />
- Duration 500 ms<br />
- Recovery time 50 s<br />
- Value 35 V<br />
Current consumption<br />
• from load voltage 1L+<br />
40 mA<br />
(no load), max.<br />
• from backplane bus 5 V DC, max. 160 mA<br />
• Power dissipation, typical 4.5 W<br />
Connection system<br />
• Requisite front connector<br />
1 x 20-pin<br />
Digital inputs<br />
• Number of digital inputs 3<br />
• Functions<br />
1 for gate start, 1 for gate stop,<br />
1 for setting the counter<br />
Input voltage<br />
- for signal "0" -28.8 to 5 V<br />
- for signal "1" +11 to +28.8 V<br />
Input current<br />
- for 1 signal, typical 9 mA<br />
6ES7 350-1AH03-0AE0<br />
Digital outputs<br />
• Number of digital outputs 2<br />
• Short-circuit protection of the Yes; clocking electronically<br />
output<br />
• Limitation of voltage induced on 2L+ (-39 V)<br />
circuit interruption to<br />
Output voltage<br />
- for 0 signal (DC), max. 3 V<br />
- for 1 signal 2L+ (-1.5 V)<br />
Output current<br />
- for 1 signal rated value 0.5 A<br />
- for 1 signal permissible range 5 mA<br />
for 0 to 60 °C, min.<br />
- für Signal 1 zulässiger Bereich 0.6 A<br />
für 0 bis 60 °C, max.<br />
Output delay at resistive load<br />
- "0" to "1", max. <strong>300</strong> µs<br />
Sensor supply<br />
5 V - sensor supply<br />
-5 V Yes; 5.2 V +/-2%<br />
- Output current, max. <strong>300</strong> mA<br />
24 V - sensor supply<br />
- 24 V Yes; 1L+ (-3V)<br />
- Output current, max. 400 mA<br />
Sensor<br />
Connectable encoders<br />
- Incremental encoder<br />
Yes; with 2 pulse trains<br />
(symmetrical)<br />
offset by 90°<br />
- Incremental encoder<br />
Yes<br />
(asymmetrical)<br />
- 24 V initiator Yes<br />
- 24 V directional sensor Yes; 1 pulse train,<br />
1 direction level<br />
Siemens ST 70 · 2005<br />
4/93