FlowCERT

More documents

Recommendations

Info

Trapezoidal Page 72 If the flow calculation is to be absolute P702 = 1 the flow will be calculated using the formula: q = vh (b + mh) Where: q = flowrate v = velocity h = head b = base width (Dim“B”) P711 m = side slope calculated from m = (B -b)/d where B = channel top width (Dim “A”) P710, b = base width (Dim “B”) P711 d = depth of channel (Dim “C”) P712
Round Pipe If the flow calculation is to be absolute P702 = 1 the flow will be calculated using the formula: q = va(h) Where: q = flowrate v = velocity a(h) = area at head Page 73
Page 1:
FlowCERT INSTRUCTION MANUAL
Page 5 and 6:
Contents Chapter 1 Start Here…...
Page 7 and 8:
Common Parameters..................
Page 11 and 12:
Chapter 1 Start Here… Congratulat
Page 13 and 14:
Functional Description The FlowCERT
Page 15 and 16:
Product Specification Physical Wall
Page 17 and 18:
Chapter 2 FlowCERT Installation Pow
Page 19 and 20:
Dimensions Wall mount The dimension
Page 21 and 22:
Cable Entry There are 6 cable gland
Page 23 and 24:
Speedy velocity sensor please refer
Page 25 and 26:
Preparation for Operation Before sw
Page 27 and 28:
Chapter 3 DUET Transducer DUET Tran
Page 29 and 30:
Mounting Plate Fixings The DUET is
Page 31 and 32: Chapter 4 Speedy Velocity Sensor Fo
Page 33 and 34: Speedy Hardware Specification Suppl
Page 35 and 36: Positioning of the Speedy sensor Th
Page 37 and 38: Step or obstruction h < 2.5% of Dia
Page 39 and 40: Page 29
Page 41 and 42: FlowCERT Parameter list for Speedy
Page 43 and 44: Chapter 5 How To Use Your FlowCERT
Page 45 and 46: Program Mode This mode is used to s
Page 47 and 48: Menu Keys The menu keys have the fo
Page 49 and 50: Note You can tell which part of the
Page 51 and 52: Using the RS232 Serial Interface Th
Page 53 and 54: Parameter Defaults Factory Defaults
Page 55 and 56: Chapter 6 Quick Set-up Guide This q
Page 57 and 58: For devices which do not match any
Page 59 and 60: Wait ….. Parameter Default Descri
Page 61 and 62: Parameter Set Value Description P21
Page 63 and 64: Point of Measurement The transducer
Page 65 and 66: Calculations ABSOLUTE If the flow c
Page 67 and 68: Example 1 ‘V’ Notch Weir In thi
Page 69 and 70: BS3680 Flumes (P700 = 2) Point of M
Page 71 and 72: U-Throated Flume ABSOLUTE If the fl
Page 73 and 74: To program the FlowCERT for Example
Page 75 and 76: RATIOMETRIC If the flow calculation
Page 77 and 78: To program the FlowCERT for Example
Page 79 and 80: RATIOMETRIC BS3680 Rectangular Weir
Page 81: Rectangular Channel Calculations AB
Page 85 and 86: V-notch angle weirs, the head is me
Page 87 and 88: Chapter 7 Parameter Guide This chap
Page 89 and 90: Relays Menu Relay 1 Relay 2 Relay 3
Page 91 and 92: OCM Menu PMD Setup Dimensions Calcs
Page 93 and 94: mA Output 1 Menu Range Operation Se
Page 95 and 96: Echo Processing Menu Xdr. 1 Status
Page 97 and 98: Device Comm Menu RS232 Setup RS485
Page 99 and 100: Parameter Listing and Descriptions
Page 101 and 102: P106 Span This parameter should be
Page 103 and 104: P125 High mA Trim This parameter al
Page 105 and 106: Alarms P210, 220, 230, 240, 250 =1
Page 107 and 108: Alarm ID Description Setpoints 6= I
Page 109 and 110: Pumps P210, 220, 230, 240, 250 = 2
Page 111 and 112: Pump Duty Description 8= First On F
Page 113 and 114: Control P210, 220, 230, 240, 250 =
Page 115 and 116: P215, P225, P235, P245, P255 Relay
Page 117 and 118: Common Parameters P216, P226, P236,
Page 119 and 120: P584 Maximum Temperature Date This
Page 121 and 122: If P700 = 3 (BS 3680 Weir) Select f
Page 123 and 124: P706 Volume Units Select the Volume
Page 125 and 126: P713 Dimension D This parameter is
Page 127 and 128: P717 Exponent This parameter is use
Page 129 and 130: Velocity The calculation of flow us
Page 131 and 132: P685 Peak width Sets the evaluation
Page 133 and 134:
Average Flow P863 Average Flow This
Page 135 and 136:
Auxiliary P810 Units This parameter
Page 137 and 138:
P822 Totaliser Decimal Places This
Page 139 and 140:
Operation P831 mA 1 Mode This param
Page 141 and 142:
mA Output 2 Parameters Range P890 m
Page 143 and 144:
Trim P896 mA 2 Low Trim If the devi
Page 145 and 146:
Stability Parameters Damping Dampin
Page 147 and 148:
P884 Peak Percent This parameter is
Page 149 and 150:
P928 Serial Number This parameter w
Page 151 and 152:
Watchdog You can check how many tim
Page 153 and 154:
P974 Start Week This parameter will
Page 155 and 156:
P979 End Month This parameter is us
Page 157 and 158:
P144 Call Type This parameter deter
Page 159 and 160:
The choices for you to enter are as
Page 161 and 162:
P995 Keys Test You should press eac
Page 163 and 164:
Chapter 8 Troubleshooting This sect
Page 165 and 166:
Parameter Record APPLICATION Operat
Page 167 and 168:
Relay 4 Parameter Details Entered V
Page 169 and 170:
Dimensions Parameter Details Entere
Page 171 and 172:
P773 Flow Breakpoint 22 -1.000 P774
Page 173 and 174:
Auxiliary Parameter Details Entered
Page 175 and 176:
Trim Parameter Details Entered Valu
Page 177 and 178:
System Information Parameter Detail
show all

FlowCERT

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?