FlowCERT

More documents

Recommendations

Info

Chapter 1 Start Here… Congratulations on your purchase of a Pulsar <strong>FlowCERT</strong>. This quality system has been developed over many years and represents the latest in high technology ultrasonic level measurement and control. It has been designed to give you years of trouble free performance, and a few minutes spent reading this operating manual will ensure that your installation is as simple as possible. About this Manual It is important that this manual is referred to for correct installation and operation. There are various parts of the manual that offer additional help or information as shown. Tips TIP At various parts of this manual you will find tips to help you. Additional Information Additional Information At various parts of the manual, you will find sections like this that explain specific things in more detail. References See Also References to other parts of the manual Page 1
Page 1: FlowCERT INSTRUCTION MANUAL
Page 5 and 6: Contents Chapter 1 Start Here…...
Page 7 and 8: Common Parameters..................
Page 12 and 13: About the FlowCERT The FlowCERT ope
Page 14 and 15: Page 4 The FlowCERT can be programm
Page 16 and 17: Digital output Volt free contacts,
Page 18 and 19: Location All electronic products ar
Page 20 and 21: The full dimensions of the enclosur
Page 22 and 23: Page 12 Wire the transducer to the
Page 24 and 25: Important Information Before applyi
Page 26 and 27: Page 16 This page left blank intent
Page 28 and 29: • The DUET should be installed su
Page 30 and 31: Fitting Options Using the fixings s
Page 32 and 33: Technical data Sensor Dimensions Pa
Page 34 and 35: Installation Limitation of Performa
Page 36 and 37: Distance from valves and slide gate
Page 38 and 39: Flumes and Channels For installatio
Page 40 and 41: Operation and parameters Quick Star
Page 42 and 43: Recovery of Speedy communications i
Page 44 and 45: 3) Auxiliary Display, scrolling twe
Page 46 and 47: Hot Keys There are five hot keys on
Page 48 and 49: There are two means of editing para
Page 50 and 51: Test Mode Test mode is used to simu
Page 52 and 53: Other commands you can use are: /LE
Page 54 and 55: Page 44 This page left blank intent
Page 56 and 57: Choose Your Application There are s
Page 58 and 59: Quick Setup Menu Quick Setup PMD Ty
Page 60 and 61:
Parameter Default Description P823
Page 62 and 63:
Exponential Devices (P700 = 1) If t
Page 64 and 65:
For a Leopald Lagco flume the head
Page 66 and 67:
Exponent Type Formula Exponent K Fa
Page 68 and 69:
To program the FlowCERT for Example
Page 70 and 71:
Calculations Rectangular Flume ABSO
Page 72 and 73:
Example 2 BS3680 U-Throated Flume I
Page 74 and 75:
BS3680 Weirs (P700 = 3) Point of Me
Page 76 and 77:
Example 3 BS3680 Rectangular Weir P
Page 78 and 79:
BS3680 Rectangular Broad Crested We
Page 80 and 81:
Velocity Area (P700 = 4) The calcul
Page 82 and 83:
Trapezoidal Page 72 If the flow cal
Page 84 and 85:
Special Devices (P700 = 5) Point of
Page 86 and 87:
RATIOMETRIC V-Notch Angle Weir (Non
Page 88 and 89:
Application Menu Operation Distance
Page 90 and 91:
Data Logs Menu Totaliser Audit P460
Page 92 and 93:
Display Menu Options Fail Safe Auxi
Page 94 and 95:
Compensation Offset Temperature Vel
Page 96 and 97:
System Menu Passcode Backup System
Page 98 and 99:
Test Menu Simulation Hardware P980
Page 100 and 101:
Dimensions P104 Measurement Units T
Page 102 and 103:
mA Input The 4-20 mA (Auxiliary) in
Page 104 and 105:
P210, P220, P230, P240, P250 - Rela
Page 106 and 107:
The third parameter for each relay
Page 108 and 109:
Important Information Setpoints are
Page 110 and 111:
Page 100 Pump Duty Description 5= D
Page 112 and 113:
The fourth parameter and the fifth
Page 114 and 115:
The third parameter for each relay
Page 116 and 117:
Important Information When using a
Page 118 and 119:
Data Log Parameters The data log pa
Page 120 and 121:
OCM Parameters PMD Setup P700 Prima
Page 122 and 123:
P702 Calculation Select the require
Page 124 and 125:
Dimensions P710 Dimension A This pa
Page 126 and 127:
P714 Roughness Coefficient (Ks) Whe
Page 128 and 129:
Calculations The following paramete
Page 130 and 131:
When P130 Device Mode = 2 Speedy, u
Page 132 and 133:
P691 High level trigger This parame
Page 134 and 135:
P804 Display Conversion The reading
Page 136 and 137:
P814 Miscellaneous Messages This pa
Page 138 and 139:
Bargraph P829 Bargraph By default t
Page 140 and 141:
Limits P836 mA 1 Low Limit This par
Page 142 and 143:
Setpoint By default the mA Output w
Page 144 and 145:
Temperature P852 Temperature Source
Page 146 and 147:
P876 Rate Distance This parameter i
Page 148 and 149:
System Parameters Passcode P921 Ena
Page 150 and 151:
LED Colour Each relay has an associ
Page 152 and 153:
Daylight Saving Time Important Info
Page 154 and 155:
P977 End Day Use this parameter to
Page 156 and 157:
Device Comm. RS232 Set Up P061 Comm
Page 158 and 159:
Example Telephone number to be dial
Page 160 and 161:
Hardware P990 Self Test If you ente
Page 162 and 163:
Page 152 This page left blank inten
Page 164 and 165:
Page 154 This page left blank inten
Page 166 and 167:
RELAYS Relay 1 Parameter Details En
Page 168 and 169:
Totaliser Audits Parameter Details
Page 170 and 171:
Breakpoints Parameter Details Enter
Page 172 and 173:
Velocity (current) Parameter Detail
Page 174 and 175:
Limits Parameter Details Entered Va
Page 176 and 177:
Rate Parameter Details Entered Valu
Page 178:
DEVICE COMM RS232 Setup Parameter D
show all

FlowCERT

Create successful ePaper yourself

Delete template?

Save as template?