Modification A00064 - US Coast Guard Response Boat-Medium

HSCG23-06-D-ARB001 Page 2 of 22 

BLOCK 14 – DESCRIPTION OF MODIFICATION (CONTINUED) 

A. This Modification incorporates and fully definitizes the following Engineering Change 

Proposals (ECPs): ECP-056 Forward Gun Mount; ECP-075 Tool Box Replacement; ECP-175 

Tow Reel Modification; and ECP-177 Air Separator. This Modification adds Sub-CLIN 5003fp for 

ECP Partial Boat Grouping Lot Hulls 98-115. The funds for the definitization of non-recurring 

prices and recurring prices for ordered Hulls will be awarded by forthcoming Delivery Orders. 

B. This Modification incorporates and fully definitizes the Cost to Prepare (CTP) and Non- 

Recurring Engineering (NRE) prices as follows: 

CLIN Labor Effort Price 

6002 CTP, ECP-056 Forward Gun Mount $1,966 

CTP, ECP-075 Tool Box Replacement $1,849 

CTP, ECP-175 Tow Reel Modification $954 

CTP, ECP-177 Air Separator $3,231 

TOTAL $8,000 

6002 NRE, ECP-056 Forward Gun Mount $17,130 

NRE, ECP-075 Tool Box Replacement $12,647 

NRE, ECP-175 Tow Reel Modification $9,270 

NRE, ECP-177 Air Separator $29,530 

TOTAL $68,577 

C. This Modification incorporates and fully definitizes the recurring (RE) credits for ordered Hulls 

45706 – 45766 in the amount of $618 per hull for ECP-056, Forward Gun Mount. The following 

table shows the breakdown of definitized credits. 

Sub-CLIN 

Hull 

Numbers 

Quantity 

Negotiated 

Credit Per 

Hull 

Extended 

Price 

5003fp ECP-056 Forward Gun Mount 45706-45715 10 -$618 -$6,180 

6003fc ECP-056 Forward Gun Mount 45716-45726 11 -$618 -$6,798 

6003gc ECP-056 Forward Gun Mount 45727-45756 30 -$618 -$18,540 

6003hc ECP-056 Forward Gun Mount 45757-45766 10 -$618 -$6,180 

Total Definitized Value: -$37,698



D. This Modification incorporates and fully definitizes the recurring (RE) costs for ordered Hulls 

45706 – 45766 in the amount of $962 per hull for ECP-075, Tool Box Replacement. The 

following table shows the breakdown of definitized costs. 

Sub-CLIN 

Hull 

Numbers 

Quantity 

Negotiated 

Price Per 

Hull 

Extended 

Price 

5003fp ECP-075 Tool Box Replacement 45706-45715 10 $962 $9,620 

6003fc ECP-075 Tool Box Replacement 45716-45726 11 $962 $10,582 

6003gc ECP-075 Tool Box Replacement 45727-45756 30 $962 $28,860 

6003hc ECP-075 Tool Box Replacement 45757-45766 10 $962 $9,620 

Total Definitized Value: $58,682 

E. This Modification incorporates and fully definitizes the recurring (RE) costs for ordered Hulls 

45698 – 45715 in the amount of $78 per hull for ECP-175 Tow Reel Modification. There will be 

no change in price for ordered Hulls 45716 – 45766. The following table shows the breakdown 

of definitized costs. 

Sub-CLIN 

Hull 

Numbers 

Quantity 

Negotiated 

Price Per 

Hull 

Extended 

Price 

5003fp ECP-175 Tow Reel Modification 45698-45715 18 $78 $1,404 

F. This Modification incorporates and fully definitizes the recurring (RE) costs for ECP-177, Air 

Separator, for ordered Hulls 45716– 45766 at no cost to the Government. 

G. This Modification establishes and incorporates the negotiated price per hull, by price period, 

for Hulls 45767 – 45850 for ECP-056, ECP-075, ECP-175 and ECP-177. Actual costs will be 

based on the Price Period in which boats are ordered. The negotiated prices are as follows: 

Price Period 

ECP-056, 

Forward Gun 

Mount 

Hulls 45767 - 

45850 

ECP-075, 

Tool Box 

Replacement 

Hulls 45767 - 

45850 

ECP-175, 

Tow Reel 

Modification 

Hulls 45767 - 

45850 

ECP-177, 

Air Separator 

Hulls 45767 - 

45850 

PP6 -$618 $962 $0 $0 

PP7 -$630 $957 $0 $0 

PP8 -$653 $987 $0 $0



H. This Modification incorporates the Scope of Work for ECP-056 Forward Weapon Mount into 

the Contract. 

SCOPE OF WORK ECP-056 

Forward Weapon Mount 

1.0 Current Configuration 

1.1. Issue – The RB-M’s forward weapon mount stand is too high, does not provide a 

suitable harness interface, does not include handholds for working on the foredeck, and 

makes access to the anchor hawse pipe difficult. 

2.0 New Desired Configuration 

2.1. De-scope - No longer manufacture the current forward weapon mount identified in 

drawing 45RBM-710-002 (Figure 1). 

Figure 1 Existing Weapons Mount. 

2.2. New Configuration – The RB-M will not be outfitted with a weapons mount. The 

contractor shall continue to provide the 3/8” deck insert as per drawing 45RBM-710-001. 

The thru holes in the deck to install the weapons mount shall continue to be drilled as per 

drawing 45RBM-110-083 see Figure 2. These holes shall be temporarily sealed for 

testing and shipping of the RB-M to maintain watertight integrity. 

2.3. Drawings- Update 3D model and 2D drawings 45RBM-710-001 and 45RBM-710- 

002 to reflect the Government provided Weapons Mount. The Government will provide 

details of the mount as drawing 45RBM-ECP056-710 Rev (A) as (enclosure 4).



Figure 2- Weapons Mount Bolt Pattern 

3.0 CDRL Deliverable Impact List – The DD Form 1692 and CDRL Impact Spreadsheet 

includes a list of Configuration Items, ILS CDRL Deliverables, and other baseline documents 

that may be impacted by the change. Other related changes that are within the scope of this 

change include modifications to other contractually required documents. The effort to 

perform these tasks, or others, should be contemplated, planned for and included in the 

ECP.



I. This Modification incorporates the Scope of Work for ECP-175 Tow Reel Modification into the 

Contract. 

SCOPE OF WORK ECP-175 

Tow Reel Modification 

1.0 Description 

1.1. The Tow Reel will have 7 evenly spaced holes match drilled with the foundation 

locking piece which matches up with the other half of the pin. These holes will allow the 

reel to be locked in a total of 7 locking positions. 

1.2. Desired Configuration- The desired configuration is shown in Figure 1. 

Figure 1 – Desired Tow Reel Configuration.



2.0 Retrofit Instructions – 

2.1. The Contractor shall develop and provide retrofit instructions for this engineering 

change using the Coast Guard’s Time Compliance Technical Order (TCTO) format. 

Submit a copy of the TCTO created for this ECP for Government review and approval 45 

number of days after ECP implementation. Allow 30 days for Government review and 

approval. 

3.0 Configuration Status Accounting – 

3.1. Configuration Status Accounting (SOW 068-2.1.4) shall be updated for this ECP 

no later than 45 days after implementation into production. Upon approval of the retrofit 

instructions, the Contractor’s CSA effort shall include capturing the retrofit instructions into 

the configuration. 

J. PART I – THE SCHEDULE, SECTION B - SUPPLIES OR SERVICES AND PRICES: 

This Modification revises the attached pages in Section B. The negotiated Sub-CLIN values, 

inclusive of all negotiated Post Award Changes to the affected Hulls to date are summarized in 

the tables below. 

. 

Changes to Sections B.1.1.b. and B.1.2.c., Firm Fixed Price Line Items are summarized in the 

following table: 

Price 

Period 

ECP-056 

Forward Gun 

Mount 

ECP-075 

Tool Box 

Replacement 

Sub- 

CLIN Hulls 

Previous 

Price 

ECP-175 

Tow Reel 

Revised 

Price 

5 5003fp LOT * $0 -$6,180 $9,620 $1,404 $4,844 

6 6003fc 45716-45726 $35,148 -$618 $962 $0 $35,492 

6 6003gc 45727-45756 $35,148 -$618 $962 $0 $35,492 

6 6003hc 45757-45780 $35,148 -$618 $962 $0 $35,492 

6 6003ic 45781-45750 $35,148 -$618 $962 $0 $35,492 

7 7003hc 45757-45780 $36,767 -$630 $957 $0 $37,094 

7 7003ic 45781-45750 $36,767 -$630 $957 $0 $37,094 

8 8003hc 45757-45780 $38,516 -$653 $987 $0 $38,850 

8 8003ic 45781-45750 $38,516 -$653 $987 $0 $38,850 

*New Sub-CLIN for incorporation of this and future ECPs for which the point of incorporation is 

between Hulls 45698 – 45715. Price is for entire LOT.



K. PART III – SECTION J, Attachment 2 – SPECIFICATION: 

Section 234-4 entitled “Crankcase Fumes” is revised in accordance with ECP-177. 

Section 582-3 entitled “Towline Reel” is revised in accordance with ECP-175. 

Section 600 entitled “General Outfit” is revised in accordance with ECP-056. 

Section 670-12 entitled “Tools, Tool Storage, and Onboard Spares Outfit” is revised in 

accordance with ECP-075. 

Section 710 entitled “Weapon Mounts” is revised in accordance with ECP-056. 

L. PART III – SECTION J, Attachment 11 – APPENDIX TO THE SCHEDULE, SECTION B: 

Attachment 11, Appendix to the Schedule, Section B, is revised to incorporate Page 2 for Sub- 

CLIN 5003fp, Partial Boat Grouping Lot. The following ECPs are added to the CLIN 5003fp Lot: 

ECP-056 Forward Gun Mount beginning with Hull 45706, ECP-075 Tool Box Replacement 

beginning with Hull 45706 and ECP-175 Tow Reel Modification beginning with Hull 45698. 

Sub- 

CLIN 

Hulls 

ECP-056 

Forward 

Gun Mount 

ECP-075 

Tool Box 

Replacement 

ECP-175 

Tow Reel 

Modification 

Quantity 

Extended 

Lot Price 

5003fp 45698-45715 $78 18 $1,404 

5003fp 45706-45715 -$618 10 -$6,180 

5003fp 45706-45715 $962 10 $9,620 

$4,844 

M. This Modification, arrived at by mutual agreement of the parties, constitutes full and final 

adjustment of the CLIN values for any direct, indirect, and consequential effects of this 

Modification including, but not limited to, cost incurred and extension of time due to delay, 

disruption, and suspension of work. 

N. This Modification does not obligate Government funds. The change in Contract value 

associated with this definitization will be awarded by forthcoming Delivery Orders. 

O. It is agreed that all other Contract requirements remain unchanged. 

P. This completes block 14.

USCG Response Boat – Medium (RB-M) 

HSCG23-06-D-ARB001 

ITEM # SUPPLIES/ SERVICES UNIT PRICE 

4005 [Orig] Display Model (as described in C.8) EACH $16,515 

PRICE PERIOD FIVE 

5001 [A00003] Project Management (as described in 

Section C.4). This CLIN is required 

whenever work, other than that 

associated with warranty 

administration, under 1002, 1009, 

1010, x003, x004, x005, x006, x007, or 

x008 is ongoing. The Government 

may order any quantity of months 

under this CLIN provided that the 

performance period is limited to the 

date established in FAR 52.216-22, 

incorporated at I.1, or, if Option Period 

1 is exercised, this price period. 

MONTH $522,052 

5002 [Orig] Vacant N/A __ N/A ___ 

5003 [Orig] Response Boat - Medium (as 

described in Section C.6). Hulls refers 

to a range of total consecutive RB-Ms 

ordered under this contract (i.e. hull 9 

cannot be ordered until hull 8 is 

ordered). The Government may order 

all or any part of this CLIN during this 

price period, provided that an 

individual hull may not be ordered 

more than once under this contract. 

5003a [A00047] Hulls 1-8 (UNUSED) EACH $2,295,417 

5003b [A00047] Hulls 9-20 (UNUSED) EACH $2,227.005 

5003c [A00047] Hulls 21-36 (UNUSED) EACH $2,210,954 

5003d [A00047] Hulls 37-66 (UNUSED) EACH $2,209,254 

5003e [A00047] Hulls 67-96 (UNUSED) EACH $1,900,483 

5003f [Orig] 

5003fc [A00062] 

Hulls 97-126 

Post Award Changes to Hulls 97-105 

EACH 

EACH 

$1,941,551 

$36,542 

Revised Price of Post Award Changes EACH 

$33,036 

to Hulls 106-126 as a result of 

incorporation of credits due the 

Government incorporated by A00059 

5003fp [A00064] 

Engineering Change Proposals 

(ECPs) on Partial Boat Grouping Lot 

98-115 (as described in Section J, 

Attch 11: Appendix A to The 

Schedule, Section B) 

LOT 

$4,844 

PART I, SECTION B A00064 Page 9 of 22 Supplies or Services and Prices







6003f [Orig] 

6003fc [A00064] 

Hulls 97-126 


EACH 

EACH 

$1,941,551 

$35,492 

6003g [Orig] 

Hulls 127-156 

EACH 

$1,987,131 

6003gc [A00064] 

Post Award Changes to Hulls 127- 

EACH 

$35,492 

156 

6003h [Orig] 

Hulls 157-180 

EACH 

$2,038,564 

6003hc [A00064] 


EACH 

$35,492 

180 

6003i [Orig] 

Hulls 181-250 

EACH 

$2,091,500 

6003ic [A00064] 


EACH 

$35,492 

250 

6004 [A00050] Stowage Cradle (as described in 

Section C.7) 

6005 [Orig] 

6010 [A00063] 

PRICE PERIOD SEVEN 

Display Model (as described in C.8) 

Spare/Repair Parts (as described in 

C.11) 






1010, x003, x004, x005, x006, x007, 

or x008 is ongoing. The Government 



performance period is limited to this 

price period. 

7002 [A00057] Post-DCB Detailed Design 

Improvements (as described in 

Section C.5.2.) 

EACH $12,389 

EACH 

$17,357 

NTE $5,000,000 

MONTH $521,467 

NTE $1,100,000 


described in Section C.6). Hulls 

refers to a range of total consecutive 

PART I, SECTION B, A00064 Page 10 of 22 Supplies or Services and Prices




RB-Ms ordered under this contract 

(i.e. hull 9 cannot be ordered until 

hull 8 is ordered). The Government 

may order all or any part of this CLIN 

during this price period, provided that 

an individual hull may not be ordered 



7003b [A00047] Hulls 9-20 (UNUSED) EACH $2,378,524 




7003f [Orig] 

7003fc [A00059] 

Hulls 97-126 


(UNUSED) 

EACH $2,312,134 

$36,153 

7003g [Orig] 

Hulls 127-156 

EACH 

$1,987,131 

7003gc [A00062] 


EACH 

$36,153 

156 (UNUSED) 

7003h [Orig] 

Hulls 157-180 

EACH 

$2,038,564 



EACH 

$37,094 

180 

7003i [Orig] 

Hulls 181-250 

EACH 

$2,091,500 



EACH 

$37,094 

250 

7004 [A00050] Stowage Cradle (as described in 

Section C.7) 

7005 [Orig] Display Model (as described in C.8) 

EACH $12,763 

EACH 

$17,792 

7010 [A00063] 

Spare/Repair Parts (as described in 

C.11) 

NTE 

$4,000,000 

PRICE PERIOD EIGHT 






MONTH $549,920 





1010, x003, x004, x005, x006, x007, 

or x008 is ongoing. The Government 



performance period is limited to the 

date established in FAR 52.216-22, 

incorporated at I.1 

8002 [A00057] Post-DCB Detailed Design 

Improvements (as described in 

Section C.5.2.) 

NTE $2,900,000 


described in Section C.6). Hulls 

refers to a range of total consecutive 

RB-Ms ordered under this contract 

(i.e. hull 9 cannot be ordered until 

hull 8 is ordered). The Government 

may order all or any part of this CLIN 

during this price period, provided that 

an individual hull may not be ordered 



8003b [A00047] Hulls 9-20 (UNUSED) EACH $2,458,513 




8003f [Orig] 

8003fc [A00059] 

Hulls 97-126 


(UNUSED) 

EACH 

EACH 

$2,352,782 

$37,874 

8003g [Orig] 

Hulls 127-156 

EACH 

$2,358,268 

8003gc [A00062] 


EACH 

$37,874 

156 (UNUSED) 

8003h [Orig] 

Hulls 157-180 

EACH 

$2,038,564 



EACH 

$38,850 

180 

8003i [Orig] 

Hulls 181-250 

EACH 

$2,091,500 



EACH 

$38,850 

250 




233-4 [Orig] Crankcase Fumes 

233-4.1 [A00064] An oil mist separator system utilizing centrifugal separation 

technology shall be provided with each engine to collect all oil mist and oil fumes 

generated and return it to the oil sump. The clean blow-by gases shall be 

dissipated through each engine’s air intake. 

233-5 [Orig] Engine Cooling System 

233-5.1 [Orig] Engine jacket water shall be cooled with raw water through an inboard heatexchanger 

system. 

233-5.1.1 [A00047] Raw water shall be strained through a duplex-type strainer fabricated 

from 70/30 copper nickel material with bronze valves. The strainers shall have 

the provision to clean one bowl, while operating the engine on the adjacent 

bowl. Strainer bowls shall be clear to allow for visual inspection. The basket 

shall be removable from the top of the strainer, without dismantling the strainer 

or disconnecting the piping. Access to the basket shall be via a quick access 

and all retaining mechanisms shall be captured to the strainer to prevent loss. 

233-5.1.2 [A00047] Each engine shall have separate sea suctions, and shall be fitted 

with bronze ball type seacocks. 

233-5.2 [Orig] Raw water systems shall have vents and drains so that the system can be 

completely drained, flushed and completely winterized without disassembling 

piping system joints. 

233-5.3 [Orig] Engine components, except charge air aftercoolers and fuel coolers, shall 

be cooled with jacket water. The jacket water shall meet the requirements on 

COMDTINST M9000.6E, Naval Engineering Manual, Chapter 233. Jacket water 

may be used as a heat source for cabin heating. 

233-6 [Orig] Emergency Shut Down 

233-6.1 [Orig] Each engine shall be provided with an emergency shut down control to 

activate an emergency shutoff for the fuel or air supply. The emergency shut down 

device shall be of the type which requires manual resetting before the engine can 

be restarted. It shall be operated remotely from the pilothouse. The actuator for 

the port engine shall be placed to the port side of the corresponding actuator for 

the starboard engine. 

233-7 [Orig] Jacket Water Heating System 

233-7.1 [Orig] Engine jacket water shall be heated to provide for rapid starting in colder 

climates. The jacket water heating system shall be powered by shore power only. 

The jacket water heating system shall be thermostatically controlled to heat the 

jacket water to a minimum temperature of 90 degrees Fahrenheit when the outside 

air temperature is at zero degrees Fahrenheit. The temperature shall be measured 

at the jacket water temperature gauge sending unit. 

233-8 [Orig] Lube Oil Sample Valve 

233-8.1 [Orig] Each engine shall have a lube oil sample valve installed as per 

COMDTINST M9000.6E, Naval Engineering Manual, Chapter 262.C.5. 

PART III, SECTION J, ATTACHMENT 2, A00064 PAGE 13 OF 22 SPECIFICATION



582 [Orig] MOORING, TOWING AND TIE DOWN FITTINGS 

582-1 [Orig] General 

582-1.1 [Orig] All towing bitts, mooring bitts and chocks shall be free of sharp edges that 

might cause damage to mooring lines or personnel. The working surface of each 

bitt and chock shall be polished. 

582-2 [Orig] Towing Fittings 

582-2.1 [Orig] An aft towing bitt shall be provided on the centerline. The towing bitt shall 

be sized to accept one round turn and three figure eights of the towline. 

582-2.2 [Orig] The RB-M towing bitt and fittings shall be designed with a factor of safety of 

1.1 on the as welded yield strength of the fitting material under an applied load, 

equal to the breaking strength of the towing line supplied, as per Section 582-3, 

applied at the highest point of the fitting. 

582-3 [Orig] Towline Reel 

582-3.1 [A00014] A towline reel shall be provided and outfitted with 2-3/4-inch 

circumference, Double Braided Nylon Line with 12" eye splices at each end so the 

total length of the line is 600 feet to the center of each eye splice. The reel shall be 

installed in a location that is readily accessible to the towing bitt. The bitter end of 

the line shall be attached to the reel using a light line or other means to provide a 

weak link. 

582-3.2 [A00064] The towline reel shall be provided with a removable crank handle and a 

locking mechanism that prevents it from free wheeling when not in use, the reel 

shall have seven evenly spaced holes to allow the wheel to be locked in 

multiple positions. 

582-4 [Orig] Mooring and Securing Fittings 

582-4.1 [Orig] The RB-M shall have a minimum of 4 sets of mooring bitts (or cleats) and 

chocks (as necessary), sized for the towline, around the perimeter of the RB-M to 

allow for mooring and alongside towing of a variety of craft types. The working 

surface of each bitt and chock shall be polished. 

582-5 [Orig] Hoisting by Slings Under Hull (Travel – Lift) 

582-5.1 [Orig] The RB-M shall be designed to allow lifting of the boat without damage by 

dual sling lifts, commonly referred to as a Travel Lift, where the slings pass under 

the hull. 

582-5.2 [Orig] When using this type of lift the load on each sling shall not exceed 20,000 

pounds in the hoisting condition. 

582-5.3 [Orig] The use of dual sling lifts shall not require any protective blocking to be 

installed. 

582-5.4 [Orig] Sling positions shall be permanently marked on the exterior of the boat in 

locations that can be easily seen from the main deck. 




SECTION 6: [Orig] OUTFIT AND FURNISHINGS 

600 [Orig] GENERAL OUTFIT 


600-1.1 [A00064] The Contractor shall provide the RB-M fully outfitted with the items 

identified in Table 600-1, 600-2, 600-3, and 600-4. 

Table 600-1 General Outfit 

General Outfit Quantity Additional Information 

Ensign, National (16”x24”) 1 Ea NSN 8345-00-245-2040 

Ensign, US Coast Guard (15”x24”) 1 Ea NSN 8345-00-242-0275 

RB-M Operator’s Handbook 1 Ea In accordance with SOW Section 

086 

Hearing Protectors, Ear Muff Style (pair) 2 Ea Peltor H10 Series Twin Cup Ear 

Muff or equal 

Hearing Protectors, Foam Insert Type, Disposable, 

Corded 

1 Box NSN 6515-00-137-6345 

Flashlight, Pelican non-explosive 2 Ea Lifesaving Systems P/N-LS #605 

(Pelican Saberlite) 

Battery, “C” Cell, Alkaline 6Ea For Pelican Flashlights 

Searchlight, Weather resistant, Hand-Held, 

Rechargeable Battery 

1 Ea Galls model SL078 or equivalent 

(See Section 332-6) 

Blankets, Wool 2 Ea NSN 7210-00-082-5668 

Blankets, Emergency 2 Ea Life Savings Systems Model 387P 

(SPACE ® Emergency Blanket) or 

equal 

Pillows 2 Ea NSN 7210-01-015-5190 

Binoculars, 7 x 50 Marine Waterproof 2 Ea NSN 6650-01-224-2555 

Push-Button Portable Signal Horn, Air, with 8oz 

Propellant 

Spare 8oz Propellant for the portable signal horn 

PART III, SECTION J, ATTACHMENT 2, A00064 PAGE 15 OF 22 SPECIFICATION 

1 Ea 

1 Ea 

Handi-wipes 2 Pkg To fit dispensers, see 644 

Medium duty wipes 1 Box NSN 7920-01-448-7053 see 670 

Paper Towels 1 Roll To fit holder, see 644 

Toilet Paper 1 Roll To fit holder, see 644 

5/8” x 2” NC 3/16 Stainless Steel Bolts 4 ea To bolt gun mount pintle to the tow



Stainless Steel Screw Hexcap , 3 1 6 , .3 7 5 -1 6 

x 1 .7 5 0 

bit 

12 ea To bolt weapons mount to deck 

Stainless Steel Washer Flat, 316, .375 24 ea To bolt weapons mount to deck 

Stainless Steel Nut Nylcok, 3 1 6 , .3 7 5 -1 6 12 ea To bolt weapons mount to deck 

Table 600-2 Navigation Equipment Outfit 

Navigation Equipment Quantity Additional Information 

Navigation Rules International- Inland 1 Ea COMDTINST M16672.2 

Parallel Plotter* 1 Ea Weems and Plath #120 or equal 

Dividers* 1 Ea Weems and Plath #176 or equal 

Slide Rule, Nautical* 1 Ea Weems and Plath #105 or equal 

Search Pattern Wheel* 1 Ea Weems and Plath #113 or equal 

Pencils, #2 

Pencil Sharpener 

5 Ea 

1 Ea 

Anemometer, Hand Held # 271 1 Ea CAGEC 18560 

Stop Watch 1 Ea NSN 6645-00-126-0286 

Penlight w/Red Lens 1 Ea Lifesaving Systems Model 601 & 601- 

1 (Pelican MityLite ®) or equal 

*Note: These items are available in a set as the Coast Guard Navigation Kit, Weems and Plath 

#100 

Table 600-3 Rescue and Survival Equipment Outfit 

Rescue, Survival & Safety Equipment Quantity Additional Information 

30” Ring Buoy, Lifesaving 2 Ea NSN 4220-00-275-3157 

Light, Marker, Distress 2 Ea ACR Electronics Inc. Automatic Crew- 

Overboard Marker Light Model SM2 

Snap hook for marker light lanyard 2 Ea Lifesaving Systems P/N 365 or equal 

Throw Bag 2 Ea Lifesaving Systems Model 237P or 

equal 

Snap hook for throw bag 2 Ea Lifesaving Systems P/N 365 or equal 

Pyrotechnics Storage Container 1 Ea Lifesaving Systems P/N 527 or equal 

Personal Flotation Devices, Type I, Adult 5 Ea Stearns Merchant Mate I or equal 




670-12 [Orig] Tools, Tool Storage, and Onboard Spares Outfit 

670-12.1 [A00064] The RB-M shall be provided with an onboard tool kit. Table 670-1 

details the required onboard tool kit. Any parts substituted as “or equal” 

shall meet all salient characteristics of the original part. Each tool bag shall 

contain a laminated inventory sheet including the part number and color 

photo of each tool provided with the kit. 

Manufacturer 

Table 670-1 Onboard Tool Kit 

Part # 

Description 

Quantity 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

211FY D/HEX SET 1 

212FMY 

T72 

TMXK4 

TMXK60 

110TMDY 

111TMMDY 

SHDP42IRO 

Set, Socket, 

Metric, Shallow, 

12-Point (12 pcs.) 

(8 to 19 mm) 

72 TOOTH STD 

HANDLE 

RATCHET 

Extension, 

Knurled, 4" 

Extension, 

Knurled, 6" 

Set, Socket, 

Shallow, 12-Point 

(10 pcs.) (3/16" to 

9/16") 

Set, Socket, 

Metric, Shallow, 

12-Point (11 pcs.) 

(5 to 14 mm) 

HARD GR 

PHILLIPS 

SHD4R HARD GRIP SD 1 

SHD8R 8IN FLAT 1 

7031A 

UIM2LM 

Bar, Close 

Quarter, 16" 

2 1/4IN XL MAG 

MIRROR 

PHT5 Pick-up Tool, 1 

1 

1 

1 

1 

1 

1 

1 

1 

1 




Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

OEX710 

OEXM710B 

BP16B 

85BCP 

95BCP 

49ACP 

91ACP 

HSG325 

Magnetic, 

Telescopic 

10PC COMBO WR 

SET 

Set, Wrench, 

Metric, 

Combination, 12- 

Point (10 pcs. In 

tray) (10-19 mm) 

Hammer, Ball 

Peen, 16 oz. 

Cutters, Diagonal, 

Vinyl Grips, 4 7/8" 

Pliers, Needle 

Nose, Vinyl Grips, 

6" 

Pliers, 

Combination Slip- 

Joint, Industrial 

Finish, Vinyl 

Grips, 9 1/4" 

Pliers, Adjustable 

Joint, Interlocking 

Channel, Industrial 

Finish, 9 1/4" 

Hacksaw, 

Professional 

BHS13A Set, Wrench, L- 

Shape, Ball Hex, 

Standard (13 pcs.) 

(.050" to 3/8') 

BHM9A 

FN100 

FXK6 

Set, Metric, 

Wrench, L-Shape, 

Ball Hex, Standard 

(9 pcs.) (1.5 to 10 

mm) 

Ratchet, Round 

Head, Standard 

Handle, 7 19/32" 

Extension, 

Knurled, Friction 

Ball, 6" 

1 

1 

1 

1 

1 

1 

1 

1 

1 

1 

1 

1 




Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

Snap On (Or 

Equal) 

FXK4 

FXK11 

FAM10E 

AD10A 

A269A 

Extension, 


Ball, 4" 

Extension, 


Ball, 11" 

Socket Driver, 

Metric, Hex, 

Standard, 10 mm 

10IN 

ADJUSTABLE 

WRENCH 

10 3/8IN CLIPS ON 

RAIL 

A271A Socket Clip, 1/4" 

Square Drive 

(package of 25) 

A267A 13 3/8” Clip on rail 2 

CTTOTEA Tote Bag 1 

1 

1 

1 

1 

2 

2 

670-12.2 [Orig] Special tools that are required for underway repairs and frequent preventive 

maintenance shall be provided and stored with the onboard spares. 

670-12.3 [A00064] The RB-M shall be provided with stowage for onboard spares. Table 

670-2 details the required onboard spare parts outfit. These onboard spare parts 

will enable the RB-M crews to correct minor underway casualties and be ready for 

operations. Any parts substituted as “or equal” shall meet all salient characteristics 

of the original part. 

Table 670-2 Onboard Spares Outfit [A00064] 

Store 

these 

items in 

Divided 

Case 

Quantity 

Per RBM Part Nomenclature 

MMC P/N or 

NIIN or Equal P/N or Equal CAGE U/I 

2 PRIMARY FUEL FILTER 01-540-3412 01030 3MHL8 EA 

2 SEPAR LID GASKET MMRBM0029 10362 3MHL8 EA 

1 250 CLASS T FUSE MMRBM0032 5118 1Q449 EA 

1 LIGHT,UTILITY,VEHICULAR 01-519-1678 90400247 61204 EA 

1 

MDE R/W PUMP COVER 

GASKET MMRBM0018 23511828 72582 EA 

1 MDE R/W IMPELLER MMRBM0019 23502086 72582 EA 

2 SECONDARY FUEL FILTER 01-022-8183 23530707 72582 EA 

1 DIVIDED CASE MMRBM0027 2673T52 3A054 EA 

1 COMPASS LED 24VDC MMRBM0012 

GM0093ASY 

(XSP PKG) 50967 EA 

1 FUSE,CARTRIDGE 3 Amp 00-010-6652 AGC-3 71400 EA 




(2673T52) 

1 FUSE,CARTRIDGE 5 Amp 00-284-6787 AGC5 71400 EA 

1 FUSE, CARTRIDGE 6 Amp 00-548-3126 AGC6 71400 EA 




1 FUSE,CARTRIDGE 1 Amp MMRBM0034 AGA1 71400 EA 

1 FUSE,CARTRIDGE 3 Amp 01-123-5210 ATC3 71400 EA 





670-12.3.1 [A00054] The Contractor shall handle, package, mark and deliver onboard 

spares in accordance with packaging instructions in SOW Section 084 and 

Contract Section D. These onboard spares shall be delivered to the 

applicable boat stations. 

670-12.3.2 [A00054] Onboard spare parts may be provided in multiple or 

separate packages, but each package shall only contain onboard spare parts 

and shall not contain any other items. Packages containing onboard spare 

parts shall be clearly marked indicating that the package contains RB-M 

onboard spare parts. 

670-12.3.3 [A00064] All items included in Table 670-2 shall be provided no later than the 

scheduled boat delivery date and no earlier than 10 days prior to the 

scheduled boat delivery date beginning with RB-M 45656. 




SECTION 7: [Orig] ARMAMENT 

703 [Orig] WEAPON STOWAGE 


703-1.1 [Orig] Interior lockable stowage shall be provided for two M240B Light Machine 

Guns (LMG), one M16 rifle, and one Remington 870 shot gun. 

710 [Orig] WEAPON MOUNTS 


710-1.1 [A00064] The RB-M shall be outfitted with one weapon mounting point to 

accommodate up to a M240B LMG. 

710-1.2 [A00064] The RB-M shall have a foundation incorporated into the aft tow bitt for 

the placement of the MK16 MOD 8 pintle type weapon stand. The foundations 

shall be adequate to support a recoil loading of 350 pounds of force and shall be 

designed with a safety factor of two on the yield strength of the material. 

710-1.3 [Orig] The MK 16 MOD 8 mount has provisions to restrict the arc of fire of the 

LMG. The base of the mount requires a foundation which has a horizontal surface 

with bolt holes to accommodate four equally spaced 5/8 inch diameter bolts on a 4- 

3/4” bolt circle with sufficient access below the foundation plate to access the bolts. 

For proper operation this foundation shall be no less than 30-1/2” and no more 

than 39” above the deck on which the gunner will be standing. 

710-1.4 [A00064] The RB-M shall have a pedestal foundation on the bow for the 

placement of a weapons mount provided by the Government. The mounting 

holes for the mount shall be temporarily sealed during testing and shipping 

of the RB-M. 

713 [Orig] AMMUNITION STOWAGE 


713-1.1 [A00037] Secure interior lockable stowage shall be provided for a minimum of four 

M19A1 ammunition containers. Each container is 11” x 3.812” x 7.25”. The weight 

of the container with ammunition is 17.8 lb. 


Section J, Attachment 11 

Appendix A (Page 2 of 2) to: Part 1 ‐ The Schedule, Section B ‐ Supplies or Services and Prices 

5003fp Partial Boat Grouping ECP Lot Hulls 98‐115 

* 

BILLING 

DATE * 

18Oct12 01 NOV 2012 07Feb13 01 MAR 2013 

45698 45699 45700 45701 45702 45703 45704 45705 45706 45707 45708 45709 45710 45711 45712 45713 45714 45715 

ECP‐056 0 0 0 0 0 0 0 0 $0 ‐618 ‐618 ‐618 ‐618 ‐618 ‐618 ‐618 ‐618 ‐618 ‐618 ‐$6,180 

ECP‐075 0 0 0 0 0 0 0 0 $0 962 962 962 962 962 962 962 962 962 962 $9,620 

ECP‐175 78 78 78 78 78 78 78 78 $624 78 78 78 78 78 78 78 78 78 78 $780 

BILLING 

DATE 

ALLOWABLE PARTIAL BILLINGS: $624 $4,220 

Total of Lot 5003fp Hulls 98‐115: 

$4,844 

* Boat delivery date 

LOT 5003fp 98‐115 Billing Schedule: 

01 NOV 2012 

01 MAR 2013 

PART III, SECTION J, ATTACHMENT 11, A00064 Page 22 of 22 Appendix A to Part 1 ‐ The Schedule, Section B, Supplies or Services and Prices

Modification A00064 - US Coast Guard Response Boat-Medium

Create successful ePaper yourself

Delete template?

Save as template?