Chapter 3 Accessing the GV-DSP LPR

More documents

Recommendations

Info

Relay OutputThe relay outputs on the terminal block can only drive a maximum load of 5V. Working inconjunction with the GV-Relay V2 module, it can drive heavier loads. Refer to the figureand table below to connect the GV-Relay V2 module to the GV-DSP LPR.Output Devices 1-4Figure 6-2GV-Relay V2 I/O Terminal BlockDO 1 Pin 1DO 2 Pin 3DO 3 Pin 5DO 4 Pin 7+ 5V Pin 9Note that you don’t need to use the DC 5V connector on the GV-Relay V2 module forpower supply, since the power is supplied from the GV-DSP LPR.Note: The GV-Relay V2 module is an optional product.36
SpecificationsSpecificationsVideo Input/OutputAudio Input/OutputVideo Compression1 Video In, 1 TV Out1 Audio In, 1 Audio OutGJPEGAudio Compression G.723Live ResolutionsLive Frame RateImage SettingAlarm and EventManagementConnectorsSecurityInstallationManagement MaintenanceProtocolStorageOperation TemperatureDimensions (W x D x H)WeightD1, CIFUp to 10 fpsBrightness, Contrast, Saturation, Hue• Events triggered by motion detection or sensorinputs• Central monitoring by LPR Center• Relay outputs triggered by sensor inputs orremotely by LPR Center• Video Input/TV Ouput: BNC ports• Audio Input/Output: Mini stereo jacks• Ethernet: 10/100Base-T• USB: 2.0• SD Card Slot: standard SD cards (Not supportSDHC cards)• Terminal Block: 4 Digital Inputs, 4 Relay Outputs,RS-232, WeigandIP address filteringWeb-based configurationFirmware upgrade through Web BrowserHTTP, TCP, UDP, DHCP, NTP, DynDNSSD Card-20~70°C174 x 145 x 40 (mm)0.75Kg37
Page 1 and 2: GV-DSP LPRUser's Manual V1.0Before
Page 3 and 4: ContentsChapter 1 Introduction ....
Page 5 and 6: 1IntroductionChapter 1 Introduction
Page 8 and 9: 1.4.2 Rear View1 2 34Figure 1-2No.
Page 10 and 11: 1. Open your web browser, and type
Page 12 and 13: Chapter 3 Accessing the GV-DSP LPRT
Page 14 and 15: 3.2.1 The Live View Window189234567
Page 16 and 17: 3.2.4 Video RecordingYou can record
Page 18 and 19: Chapter 4 Administrator ModeThe Adm
Page 20 and 21: [Video Signal Type] The GV-DSP LPR
Page 22 and 23: 4.1.3 LPR CenterWhen the alarm even
Page 24 and 25: 4.2.2 Output SettingThe GV-DSP LPR
Page 26 and 27: [UMTS Setting] UMTS stands for Univ
Page 28 and 29: To enable the DDNS function:1. Enab
Page 30 and 31: 4.4 ManagementThe Management sectio
Page 32 and 33: [Storage Settings]• Enable saving
Page 34 and 35: 4.4.5 ToolsThis section allows you
Page 36 and 37: 5.1.2 Upgrading Firmware by Using t
Page 38 and 39: 3. Click the Export Settings button
Page 42: Country SupportAustralia, Austria,

Chapter 3 Accessing the GV-DSP LPR

Create successful ePaper yourself

Delete template?

Save as template?