Chapter 3 Accessing the GV-DSP LPR
Chapter 3 Accessing the GV-DSP LPR Chapter 3 Accessing the GV-DSP LPR
3. Click the Export Settings button. This dialog box appears.Figure 5-54. Click the Browse button to assign a file path.5. Type Password, and click Export Settings to save the backup file.To restore the settings:1. In Figure 5-3, click the Import Settings tab. This dialog box appears.Figure 5-62. Click the Browse button to locate the backup file (.dat).3. Click Update Settings to start restoring.34
6The I/O Terminal BlockChapter 6 The I/O Terminal BlockThe 16-pin terminal block, located on the rear panel, provides the interface to: four digitalinputs, four relay outputs, an RS-232 interface, a Wiegand interface and auxiliary power.The I/O terminal block can be used to develop applications for motion detection, eventalerts, access control and a variety of other functions.Note: RS-232 and Wiegand Interface are NOT functional now.Figure 6-1Pin AssignmentThe pin assignment for the terminal block is described in the table below.Pin Function Pin Function1 Relay Output 1 9 DC 5V Out for GV-Relay Module2 Digital Input 1 10 Ground3 Relay Output 2 11 RS-232 (TX)4 Digital Input 2 12 Wiegand D05 Relay Output 3 13 RS-232 (RX)6 Digital Input 3 14 Wiegand D17 Relay Output 4 15 Ground8 Digital Input 4 16 DC 12V Out for Wiegand Card Reader35
- Page 1 and 2: GV-DSP LPRUser's Manual V1.0Before
- Page 3 and 4: ContentsChapter 1 Introduction ....
- Page 5 and 6: 1IntroductionChapter 1 Introduction
- Page 8 and 9: 1.4.2 Rear View1 2 34Figure 1-2No.
- Page 10 and 11: 1. Open your web browser, and type
- Page 12 and 13: Chapter 3 Accessing the GV-DSP LPRT
- Page 14 and 15: 3.2.1 The Live View Window189234567
- Page 16 and 17: 3.2.4 Video RecordingYou can record
- Page 18 and 19: Chapter 4 Administrator ModeThe Adm
- Page 20 and 21: [Video Signal Type] The GV-DSP LPR
- Page 22 and 23: 4.1.3 LPR CenterWhen the alarm even
- Page 24 and 25: 4.2.2 Output SettingThe GV-DSP LPR
- Page 26 and 27: [UMTS Setting] UMTS stands for Univ
- Page 28 and 29: To enable the DDNS function:1. Enab
- Page 30 and 31: 4.4 ManagementThe Management sectio
- Page 32 and 33: [Storage Settings]• Enable saving
- Page 34 and 35: 4.4.5 ToolsThis section allows you
- Page 36 and 37: 5.1.2 Upgrading Firmware by Using t
- Page 40 and 41: Relay OutputThe relay outputs on th
- Page 42: Country SupportAustralia, Austria,
3. Click <strong>the</strong> Export Settings button. This dialog box appears.Figure 5-54. Click <strong>the</strong> Browse button to assign a file path.5. Type Password, and click Export Settings to save <strong>the</strong> backup file.To restore <strong>the</strong> settings:1. In Figure 5-3, click <strong>the</strong> Import Settings tab. This dialog box appears.Figure 5-62. Click <strong>the</strong> Browse button to locate <strong>the</strong> backup file (.dat).3. Click Update Settings to start restoring.34