GV-Video Server

More documents

Recommendations

Info

4.7.4 UMTSUMTS stands for Universal Mobile Telephone System. UMTS is a third-generation (3G)broadband, packet-based transmission of text, digitized voice, video, and multimedia atdata rates up to 2 megabits per second. UMTS offers a consistent set of services to mobilecomputer and phone users, no matter where they are located in the world.After a mobile broadband device (supporting UMTS, HSDPA, etc.) is attached to the USBport on the rear panel and the UMTS function is enabled, the GV-Video Server can havewireless broadband access. For supported mobile broadband devices, see Appendix B.Figure 4-33• PIN number: Type the PIN number that is provided by your network operator.• Access Point Name (APN): Type Access Point Name that is provided by yournetwork operator.• Username: Type a valid username to enable the UMTS service from your networkoperator.• Password: Type a valid password to enable the UMTS service from your networkoperator.74
4Administrator Mode• IP Address: The IP address of the GV-Video Server will be displayed after enablingthe UMTS service. The next time when you want to log in the GV-Video Server, youneed to enter the IP address into your browser. If you use the UMTS connection withdynamic IP addresses, first use the DDNS function to get a domain name linking to theGV-Video Server’s changing IP address. For details on the DDNS, see 4.7.3 AdvancedTCP/IP.• Maximum Transmission Unit: Type the Maximum Transfer Unit (MTU). The defaultvalue is 1500.• Retain UMTS Connection: Select this option to check the UMTS connection statusand use the drop-down list to specify the desired time length for check frequency. TheGV-Video Server will rebuild the connection if disconnection is detected.• Check VPN Connection: (Note this option is only available for GV-VS02A, GV-VS04Aand GV-VS12.) Select this option to check the VPN (Virtual Private Network)connection status. To check the IP address, type the target IP address in the CheckTarget IP Address field.• 3G Connection Status: (Note this option is only available for GV-VS02A, GV-VS04Aand GV-VS12.) Indicates the connection status of UMTS or VPN.4.7.5 MulticastNote this function is only available for GV-VS02 (Firmware Version 1.46), GV-VS02A(Firmware Version 1.01 or later) and GV-VS04A.The multicast provides a mechanism for sending a single video and audio stream to agroup of hosts. Only the hosts that have joined a multicast group can send and receive themulticast streams. The multicast streams are only sent to hosts on a local network.This configuration page provides two settings. One is to allow the GV-Video Server to joina multicast group. The other is to allow the GV-Video Server to receive audio broadcastingfrom other hosts in a multicast group.IMPORTANT: For GV-VS02 users, the Multicast function only works when the videoresolution is set to CIF (360 x 240 / 360 x 288) or QCIF (176 x 112 / 176 x 144).75
Page 1 and 2:
GV-Video ServerUser's ManualBefore
Page 3 and 4:
PrefaceWelcome to the GV-Video Serv
Page 5 and 6:
3.2.13 I/O Control.................
Page 7 and 8:
7.2 Receiving Cardholder Data from
Page 10 and 11:
1.1.3 GV-VS12Figure 1-31. AC Power
Page 12 and 13:
1.5 OptionsOptional devices can exp
Page 14 and 15:
1.6.1.2 GV-VS02A8761 2 3 4 5Figure
Page 16 and 17:
1.6.1.4 GV-VS04AFigure 1-8No. NameF
Page 18 and 19:
1.6.2.2 GV-VS02AFigure 1-10No. Name
Page 20 and 21:
1.6.2.4 GV-VS04AFigure 1-12No. Name
Page 22 and 23:
1. Open your web browser, and type
Page 24 and 25:
Chapter 3 Accessing the GV-Video Se
Page 26 and 27:
1110981 2 3 4 5 6 7Figure 3-3No. Na
Page 28 and 29:
3.2.3 Snapshot of a Live VideoTo ta
Page 30 and 31:
Picture-and-Picture ViewWith the Pi
Page 32 and 33: • Auto Snapshot: The snapshot of
Page 34 and 35: 3.2.11 PTZ ControlTo open the PTZ c
Page 36 and 37: 3.2.13 I/O ControlThe I/O Control w
Page 38 and 39: Chapter 4 Administrator ModeThe Adm
Page 40 and 41: 4.1 Video & MotionThis section incl
Page 42 and 43: 4.1.2 Video SettingsFigure 4-334
Page 44 and 45: [Video Signal Type]• Auto detect
Page 46 and 47: 4.1.3 Motion DetectionMotion detect
Page 48 and 49: 4.1.5 Text OverlayNote this option
Page 50 and 51: To configure the tampering alarm:1.
Page 52 and 53: 4.1.8 Video Channel Source Settings
Page 54 and 55: 4.2.2 Input/Output SettingsInput Se
Page 56 and 57: 4.2.3 GPS/WiegandYou can select eit
Page 58 and 59: 4.2.4 BuzzerNote this function is o
Page 60 and 61: • Send to: Type the e-mail addres
Page 62 and 63: [Alarm Settings]• Motion Detectio
Page 64 and 65: To enable the Center V2 connection:
Page 66 and 67: 3. Port Number: Match the port to P
Page 68 and 69: To enable the GV-GIS connection:1.
Page 70 and 71: 3. Port Number: Match the communica
Page 72 and 73: 4.3.8 ViewLog ServerThe ViewLog Ser
Page 74 and 75: 4.5 Recording ScheduleThe schedule
Page 76 and 77: 4.7 NetworkThe Network section incl
Page 78 and 79: 4.7.2 Wireless-Client ModeTo use th
Page 80 and 81: 4.7.3 Advanced TCP/IPThis section i
Page 84 and 85: Figure 4-34• Multicast Host Name:
Page 86 and 87: 4.8 ManagementThe Management sectio
Page 88 and 89: 4.8.2 GPS Maps SettingsNote this fu
Page 90 and 91: • Keep days (1-255): Specify the
Page 92 and 93: 4.8.5 Log InformationThe System Boo
Page 94 and 95: 4.8.7 ToolsThis section allows you
Page 96 and 97: 5.2.1 Playback Using USB Mass Stora
Page 98 and 99: 5.2.3 Playback of GPS TracksOn GV-S
Page 100 and 101: 5.2.4 Playback of Daylight Saving T
Page 102 and 103: 6.1.1 Using the Web Interface1. In
Page 104 and 105: 5. Click the Firmware Upgrade tab.
Page 106 and 107: 6.3 GPS TrackingNote this function
Page 108 and 109: 6.4 Restoring to Factory Default Se
Page 110 and 111: 6.5.3 The Watermark Proof Window1 3
Page 112 and 113: 7.1 Setting Up IP CamerasTo set up
Page 114 and 115: Previewing Video and Setting AudioT
Page 116 and 117: [GV-GIS Setting]Receive the GPS dat
Page 118 and 119: 2. At the local computer, open the
Page 120 and 121: For details on creating an E-Map fi
Page 122 and 123: To define how to display the receiv
Page 124 and 125: 8.3 Dispatch ServerThe Dispatch Ser
Page 126 and 127: 9.1.2 Relay OutputThe relay outputs
Page 128 and 129: 9.2.2 RS-232 Terminal BlockThe RS-2
Page 130 and 131: 10.1 PDAGView V2 is a remote view a
Page 132 and 133:
2. Click the button located at the
Page 134 and 135:
10.1.5 Other FunctionsIn addition t
Page 136 and 137:
Viewing Input-Triggered EventsAll i
Page 138 and 139:
Viewing Camera StatusTo view the ca
Page 140 and 141:
10.2.3 Connecting to GV-Video Serve
Page 142 and 143:
10.2.4 Playing Back the Recordings
Page 144 and 145:
10.3.3 Connecting to GV-Video Serve
Page 146 and 147:
10.4 3G Mobile PhoneWithout install
Page 148 and 149:
4. Select Live to receive the Live
Page 150 and 151:
SpecificationsVideoModel GV-VS02 GV
Page 152 and 153:
EnvironmentModel GV-VS02 GV-VS02A G
Page 154:
C. Settings for Internet Explore 8I
show all

GV-Video Server

Create successful ePaper yourself

Delete template?

Save as template?