ATTO ExpressSAS Host and RAID Adapter Installation and Operation Manual

More documents

Recommendations

Info

Driver Parameters:------------------num_sas_addr=1, sgl_page_size=512,num_targets=256, event_log_mask=0x00000001,num_sg_lists=1024, cmd_per_lun=7,can_queue=128, sg_tablesize=255,atto_max_sectors=65535, cmd_retry_count=20,io_time_out=30, change_notification=1,old_device_reset=0Adapter Information:--------------------Model: ATTO ExpressSAS H680SAS Address: 50010860:00104a40Discovered Devices:# TargID SAS Address----------------------------------NoneStatistics:-----------Time elapsed (ms) : 86530Commands completed : 0Outstanding commands : 0Max outstanding commands: 0ATTO CLI ToolsATTO provides a set of Command Line Interface (CLI)tools for managing ATTO adapters from the ServiceConsole of an ESX/ESXi host. These tools aredistributed in a compressed TAR file with the name:vmw_app_hbacli_{date}.tgz. Replace {date} with theactual date-string.To install ATTO CLI Tools on an ESX/ESXi host:1 Copy the TAR file to the ESX/ESXi host.2 Extract the contents of the tar file using: tar xvzf3 Change to the extracted directory using cdvmw_app_hbacli_{date}4 Run the installer: ./cli_install.sh5 Follow the instructions to complete theinstallation.The following ATTO CLI tools are available:atinfo - View basic information about ATTO adaptersand their attached devices.atflash - View and update the flash version of ATTOadapters.atfcnvr - View and modified parameters in theNVRAM of ATTO Celerity adapters to fine-tuneadapter performance and behavior. You can save andrestore NVRAM settings from a file using this tool.atsasnvr - View and modify parameters in the NVRAMof ATTO ExpressSAS adapters to fine-tune adapterperformance and behavior. You can save and restoreNVRAM settings from a file using this toolNoteOn ESX 4.x, the ATTO CLI Tools shouldNOT be installed on a VMFS volume.Instead, they should be installed in anappropriate location on the local disk, suchas /usr/sbin. On ESXi 4.x and ESXi 5.0, theCLI tools should be installed on permanentstorage, such as a VMFS volume.v ATTO Technology Inc. ATTO ExpressSAS Host & RAID Adapter Installation and Operation Manual
Appendix C Standards and CompliancesThe equipment described in this manual generates and uses radio frequency energy. The Technical Specificationsheet for the ATTO ExpressSAS Host Adapter shows certifications for each model.FCC standards: radio and television interferenceThis equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed andused in accordance with the instruction manual, may cause interference to radio communications. However, thereis no guarantee that interference will not occur in a particular installation. If this equipment does causeinterference to radio or television reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna• Increase the separation between the equipmentand receiver• Connect the equipment into an outlet on a circuitdifferent from that to which the receiver isconnected• Consult the dealer or an experienced radio/TVtechnician for helpCanadian standardsThis Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.European standardsDeclaration of ConformityThis following statement applies to the ATTO ExpressSAS Host Adapter.This device has been tested in the basic operating configuration and found to be compliant withthe following European Union standards: Application of Council Directive: 89/336/EECStandard(s) to which conformity is declared:EN55024:2002; EN55022:2002 CLASS BThis Declaration will only be valid when this product is used in conjunction with other CE approved devices andwhen the entire system is tested to the applicable CE standards and found to be compliant.The ATTO ExpressSAS Host Adapter cards comply with Directive 2002/95/EC on theRestriction of the Use of Hazardous Substances in Electrical and Electronic Equipment(RoHS). Contact your ATTO representative regarding RoHS compliant products.vi ATTO Technology Inc. ATTO ExpressSAS Host & RAID Adapter Installation and Operation Manual
Page 1 and 2: ATTO ExpressSAS Host and RAID Adapt
Page 3 and 4: Contents1 ATTO Provides Storage Sol
Page 5 and 6: 1 ATTO Provides Storage SolutionsAT
Page 7 and 8: H60F technical specifications• 16
Page 9 and 10: R608 technical specifications• Ei
Page 11 and 12: WindowsInstalling from the ExpressS
Page 13 and 14: VMware ESX/ESXi 4.1 (ExpressSAS H6x
Page 15 and 16: 2.1 New Windows OS InstallationWhen
Page 17 and 18: 2.2 New OS X InstallationBoot suppo
Page 19 and 20: 3 Install HardwareUse this chapter
Page 21 and 22: Installing CacheAssure (6Gb RAID Ad
Page 23 and 24: Bracket detailsExhibit 3-4 ExpressS
Page 25 and 26: Exhibit 3-12 ExpressSAS R680 Adapte
Page 27 and 28: Exhibit 3-18 ExpressSAS H6F0 Adapte
Page 29 and 30: Exhibit 3-23 ExpressSAS R60F Adapte
Page 31 and 32: Connections on the R608 and R60FThe
Page 33 and 34: Exhibit 3-3 Connect an H608 or H60F
Page 35 and 36: Exhibit 3-4SES-I2C Wire chart for R
Page 37 and 38: Example ConfigurationsExample 1 R60
Page 39 and 40: 4 TroubleshootingThis chapter conta
Page 41 and 42: TermSES-I2CSGPIOSidebandConnectorTr
Page 43: PARAMETERDESCRIPTIONnum_targets Max

ATTO ExpressSAS Host and RAID Adapter Installation and Operation Manual

Create successful ePaper yourself

Delete template?

Save as template?