ATTO ExpressSAS Host and RAID Adapter Installation and Operation Manual

More documents

Recommendations

Info

6 Make sure the NV Memory Card is firmlyseated by gently pushing the card down ontothe ATTO RAID Adapter, as shown:7 Turn the Host Adapter over so that you can seethe back of the printed circuit board. Use thetwo supplied screws to finish secure the NVMemory Card onto your RAID adapter.8 Use an ESD-safe crosshead screwdriver tosecure the screws.Power Module Installation-----------------------------------------------------------------------NoteIt is the user’s preference to install the PowerModule while the ATTO Host Adapter isoutside of the computer, or install the PowerModule while the Host Adapter is seated init’s PCI Express slot. If you have questionsabout how to remove an expansion cardfrom your system, consult your computer’sdocumentation. In these directions, we willassume the card is seated in its PCI Expressslot.1 Remove the Power Module from itselectrostatic safe packaging.2 Select an area for placement of the PowerModule inside of the computer. Make sure itcan be mounted securely and that the PowerModule’s power cord can reach the HostAdapter, specifically the NV Memory Card’spower jack.3 Use the heavy-duty, industrial adhesive, shownin Exhibit 3-3 to mount the module. Removeone side of the paper backing and apply it to thePower Module.Exhibit 3-3 Applying mount adhesive-----------------------------------------------------------------------4 Remove and expose the other side of theadhesive.5 Mount the Power Module into the computer.6 Plug the Power Module power cord into theNon-Volatile Module (on the RAID adapter).The plug is keyed so that it can only be pluggedin one way. Make sure that the plug is fullyinserted.7 Close your computer case.8 You may power on your system.WARNINGBe careful handling the Power Module after ithas been installed and powered. It may be livewith power. If the board is mishandled while it isattached it may become shorted and/or damaged.18 ATTO Technology Inc. ATTO ExpressSAS Host & RAID Adapter Installation and Operation Manual
Bracket detailsExhibit 3-4 ExpressSAS H644 Adapter brackets.Exhibit 3-6 ExpressSAS H680 Adapter brackets.Exhibit 3-5 ExpressSAS H608 Adapter brackets.Exhibit 3-7 ExpressSAS H60F Adapter brackets.19 ATTO Technology Inc. ATTO ExpressSAS Host & RAID Adapter Installation and Operation Manual
Page 1 and 2: ATTO ExpressSAS Host and RAID Adapt
Page 3 and 4: Contents1 ATTO Provides Storage Sol
Page 5 and 6: 1 ATTO Provides Storage SolutionsAT
Page 7 and 8: H60F technical specifications• 16
Page 9 and 10: R608 technical specifications• Ei
Page 11 and 12: WindowsInstalling from the ExpressS
Page 13 and 14: VMware ESX/ESXi 4.1 (ExpressSAS H6x
Page 15 and 16: 2.1 New Windows OS InstallationWhen
Page 17 and 18: 2.2 New OS X InstallationBoot suppo
Page 19 and 20: 3 Install HardwareUse this chapter
Page 21: Installing CacheAssure (6Gb RAID Ad
Page 25 and 26: Exhibit 3-12 ExpressSAS R680 Adapte
Page 27 and 28: Exhibit 3-18 ExpressSAS H6F0 Adapte
Page 29 and 30: Exhibit 3-23 ExpressSAS R60F Adapte
Page 31 and 32: Connections on the R608 and R60FThe
Page 33 and 34: Exhibit 3-3 Connect an H608 or H60F
Page 35 and 36: Exhibit 3-4SES-I2C Wire chart for R
Page 37 and 38: Example ConfigurationsExample 1 R60
Page 39 and 40: 4 TroubleshootingThis chapter conta
Page 41 and 42: TermSES-I2CSGPIOSidebandConnectorTr
Page 43 and 44: PARAMETERDESCRIPTIONnum_targets Max
Page 45 and 46: Appendix C Standards and Compliance

ATTO ExpressSAS Host and RAID Adapter Installation and Operation Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?