Richter Bass
RB5 RB6 RB7 Manual - 2011 - Issue 1.cdr - Laney RB5 RB6 RB7 Manual - 2011 - Issue 1.cdr - Laney
L Z B1 2 3 4L Z B1 2 3 4L Z B1 2 3 4REAR PANEL CONTROLSAll controls common - unless otherwise stated112123456Power inlet socket. Connect to yourpower source. Make sure thespecified voltage is correct for yourcountry!This drawer contains the main safetyfuse for the unit. USE ONLY THECORRECT SIZE AND RATING OFFUSE AS SPECIFIED ON THEPANEL.Serial Number and model of yourunit.This socket should be used toconnect an extension-cabinet. Theimpedance of the extension-cabinetmust not be less than 8 Ohms.Connecting cabinets that have alower impedance than 8 Ohms willresult in the amplifier overheating.T6.3A L 250VContinual use in this manner maycause permanent damage.Connecting a cabinet with animpedance of greater than 8 Ohmswill cause no damage to the amplifierbut will result in a reduced outputlevel. (When using an extension cabinet the internal speaker remains connected)23Send and return sockets are provided for connecting external effects-units. You can also use the Send socket as a line out ifyou wish.4Socket for connecting external tuner. This output is taken before any processing so the Volume control may be turned downfor silent tuning.56
BLOCK DIAGRAMINPUTNORMALHIGHPADTUNER OUTGAIND.I. OUTONACTIVECOMPRESSORSECTIONEQ SECTIONVOLUMESENDFX LOOPRETURNThis loop is a series type so allyour signal will go through your FX unit.POWERAMPOUTPUTACTIVEX-OVERH.F HORNLIMITERSECTIONINTERNALLOUDSPEAKERAmplifier connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off yourequipment. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc. BEFOREturning on your Bass Amplifier. Many products have large transient surges at turn on and off which can cause damage to yourspeakers. By turning on your Bass Amplifier LAST and making sure its Volume control is set to minimum any transients from otherequipment will not reach your loudspeakers. Wait until all system parts have stabilised; usually a couple of seconds. Similarly whenturning off your system always turn down the Volume control on your Bass Amplifier and then turn off its power before turning offother equipment.Cables: Never use shielded or microphone cable for any speaker connections as this will not be substantial enough to handle theamplifier load and could cause damage to your amplifier system.Servicing: The user should not attempt to service these products. Refer all servicing to qualified service personnel.13
- Page 1 and 2: Richter Bass
- Page 3 and 4: INSTRUCTIONS IMPORTANTES DE SECURIT
- Page 5 and 6: INSTRUCCIONES IMPORTANTES PARA SU S
- Page 7: SPECIFICATIONSSupply Voltage on all
- Page 10 and 11: FRONT PANEL CONTROLSAll controls co
- Page 14 and 15: L Z B1 2 3 4RB5SAMPLE SYSTEMSYour C
- Page 16: OPERATING INSTRUCTIONS - Issue: 1
L Z B1 2 3 4L Z B1 2 3 4L Z B1 2 3 4REAR PANEL CONTROLSAll controls common - unless otherwise stated112123456Power inlet socket. Connect to yourpower source. Make sure thespecified voltage is correct for yourcountry!This drawer contains the main safetyfuse for the unit. USE ONLY THECORRECT SIZE AND RATING OFFUSE AS SPECIFIED ON THEPANEL.Serial Number and model of yourunit.This socket should be used toconnect an extension-cabinet. Theimpedance of the extension-cabinetmust not be less than 8 Ohms.Connecting cabinets that have alower impedance than 8 Ohms willresult in the amplifier overheating.T6.3A L 250VContinual use in this manner maycause permanent damage.Connecting a cabinet with animpedance of greater than 8 Ohmswill cause no damage to the amplifierbut will result in a reduced outputlevel. (When using an extension cabinet the internal speaker remains connected)23Send and return sockets are provided for connecting external effects-units. You can also use the Send socket as a line out ifyou wish.4Socket for connecting external tuner. This output is taken before any processing so the Volume control may be turned downfor silent tuning.56
Change language