Technical Data - ChemCenters

Product Description Sheet1001 Trout Brook CrossingRocky Hill, CT 06067-3910Telephone: (860) 571-5100FAX: (860) 571-5465Hysol® Product 1CIndustrial Products, August 2001DescriptionLoctite® Hysol® 1C is a general purpose adhesive and sealantthat bonds, seals, and repairs a wide variety of materialsincluding metals, most plastics, and wood. Hysol 1C is alsoavailable in gray (6C) and black (11C).FeaturesWhite Color (See Above)Machineable, SandableWithstands Severe EnvironmentsHigh Service TemperatureRoom Temp or Heat CureLow Outgassing PropertiesTypical UncuredPart A Part B MixedPropertiesPot Life @ 77°F, 100-- -- 20 to 25grams minsColor White Beige WhiteViscosity, cP140,000 to330,000550,000 to870,000200,000 to500,000Specific Gravity 1.55 1.65 1.55Mix RatioBy weight 100 44 --By volume 2.5 1 --Shear Strength, psi, ASTM D 1002 Etched AluminumCure Schedule Test Temp o F Typical Value3 Days @ 77 o F -67 100077 1750180 1500250 700300 5002 Hours @ 140 o F -67 150077 2100180 1700250 750300 550Typical PropertiesTypical ValueHardness, Shore D 80Tg, °C 98CTE, ASTM D 696, in/in/ °C 63 x 10 -6Thermal Conductivity, cal x cm/cm 2 x 13 x 10 -4secs x °CElectrical PropertiesTypical ValueDielectric Strength, ASTM D149, V/mil 350Dielectric Constant, MIL 1-16923. K 1kHz 6.1Dissipation Factor, ASTM D 150 1kHz 0.09Outgassing Performance NASA 1124Total Mass Loss, % 0.81Collected Volatile Condensable Material, % 0,02HandlingMixing: This product requires mixing two components togetherjust prior to application. Complete mixing is necessary. Thetemperature of the separate components prior to mixing is notcritical, but they should be close to room temperature.Mixing - Bulk: Combine Part A (resin) and Part B (hardener) inthe correct ratio and mix thoroughly until the color andconsistency are uniform. EPOXI-PATCH® Tube Kits have beendesigned so that squeezing EQUAL LENGTH BEADS of Part A& Part B will give proper ratio. Ratios given above can be usedfor measuring larger amounts. Mixing the adhesive just prior touse is recommended. Heat buildup during or after mixing isnormal. Do not mix quantities greater than two pounds asdangerous heat buildup can occur causing uncontrolleddecomposition of the mixed adhesive. Mixing smaller quantitieswill minimize the heat buildup.Application: Bonding surfaces should be clean and dry. Oncethe adhesive is applied, the bonded parts should be held incontact until the part has developed handling strength. It is notnecessary to clamp the parts unless movement during cure islikely.Cure: Complete cure is obtained after three days at roomtemperature. After 24 hours, approximately 90% of full cureproperties are attained. When in a bonded joint, Hysol 1C willachieve handling strength in 3-4 hours at 77°F (note: this canvary with different bond configurations). Hysol 1C can also becured with heat such as; 2 hours at 140°F, 1 hour at 180°F, or20-30 minutes at 250°F. Heat cures can be modified to achievea desired degree of cure from handling strength to full cure.Clean Up: It is important to remove excess adhesive from thework area and application equipment before it hardens. Manycommon solvents and citrus cleaners are suitable for removinguncured adhesive.Packaging4.0 oz. Epoxi-Patch Tube KitsQuart, One Gallon and Five Gallon and Drum SystemsGENERAL INFORMATIONThis product is not recommended for use in pure oxygenand/or oxygen rich systems and should not be selected asa sealant for chlorine or other strong oxidizing materials.For safe handling information on this product, consult theMaterial Safety Data Sheet, (MSDS).NOT FOR PRODUCT SPECIFICATIONSTHE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.PLEASE CONTACT LOCTITE CORPORATION QUALITY DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS ON SPECIFICATIONS FOR THIS PRODUCT.ROCKY HILL, CT FAX: +1 (860)-571-5473 DUBLIN, IRELAND FAX: +353-(1)-451 - 9959Loctite and Hysol are Trademarks of Loctite Corporation USA

Hysol 1C August 2001StorageStore product in unopened container in a cool dry location. Idealconditions are within the range 8 to 21 degrees C (46 to 70degrees F) and are recommended for long term storage.Exposure to higher temperatures (greater than 28 degrees C)for prolonged periods should be avoided as extended exposureto warm conditions can adversely affect product properties. Forfurther specific shelf life information, contact your local TechnicalService Center.NoteThe data contained herein are furnished for information only andare believed to be reliable. We cannot assume responsibility forthe results obtained by others over whose methods we have nocontrol. It is the user's responsibility to determine suitability forthe user's purpose of any production methods mentioned hereinand to adopt such precautions as may be advisable for theprotection of property and of persons against any hazards thatmay be involved in the handling and use thereof. In light of theforegoing, Loctite Corporation specifically disclaims allwarranties expressed or implied, including warranties ofmerchantability or fitness for a particular purpose, arisingfrom sale or use of Loctite Corporation’s products. LoctiteCorporation specifically disclaims any liability forconsequential or incidental damages of any kind, includinglost profits. The discussion herein of various processes orcompositions is not to be interpreted as representation that theyare free from domination of patents owned by others or as alicense under any Loctite Corporation patents that may coversuch processes or compositions. We recommend that eachprospective user test his proposed application before repetitiveuse, using this data as a guide. This product may be covered byone or more United States or foreign patents or patentapplications.Loctite and Hysol are Registered Trademarks of Loctite Corporation U.S.A.