Operating Manual R&S SMIQ - Volume 1 - Rohde & Schwarz

More documents

Recommendations

Info

<strong>SMIQ</strong>SOURce:NADC Subsystem[:SOURce]:NADC:SLOT:TYPE TCH | SHORt | ADATaThe command selects the type of burst (slot) defined in the standard.TCH Normal communication channel with the fields defined by the standard.ADATa All data (without predefined SYNC, SACCh, CDVCc and RSVD fields)SHORt Only used for uplink to set up TCH.Example: :SOUR:NADC:SLOT2:TYPE TCH *RST value is TCH[:SOURce]:NADC:SLOT:LEVel OFF | ATT | FULLThe command determines the power stage of the slot.OFF The slot is inactive.For UPLINK, the source is always at full power. Therefore, in the case of aDOWNLINK TCH burst, only a series of 1's is sent instead of the data.ATT The power is reduced by the amount defined by :NADC:SLOT:ATTFor a DOWNLINK TCH burst this setting is not valid.FULL Full power (predefined by level setting)Example: :SOUR:NADC:SLOT2:LEV ATT *RST value is FULL[:SOURce]:NADC:SLOT:PRESetThe command sets all the parameters of the slot to the values defined by the standard as afunction of the type set above and the direction (LINK). This command triggers an event andhence has no *RST value and no query.Example: :SOUR:NADC:SLOT2:PRES[:SOURce]:NADC:SLOT[:SOURce]The commands for determining the source for the data contents are under this node. The sourceis either a PRBS generator (with different sequence length), the data input SER DATA or a datalist.Selection of data source for the data fields of the burst:PN9 to 23 PRBS generator has been selectedDLISt Data of a programmable data listSDATa Data from data input SER DATA[:SOURce]:NADC:SLOT[:SOURce]:SACChannel PN9 | PN11 | PN15 | PN16 | PN20 | PN21 |PN23 | DLISt | SDATaThe command determines the data source for the data words.Example: :NADC:SLOT3:SACC PN15 *RST value is PN9[:SOURce]:NADC:SLOT[:SOURce]:SACChannel:DLISt ‘name’The command selects a data list. This list will not be used unless it is set as a data source bymeans of the :NADC:SLOT:SACC DLIS command. This command triggers an event and hencehas no *RST value.Example: :NADC:SLOT:SACC:DLIS ’test’[:SOURce]:NADC:SLOT[:SOURce]:DATA PN9 | PN11 | PN15 | PN16 | PN20 | PN21 | PN23 |DLISt | SDATaThe command determines the data source for the data words.Example: :SOUR:NADC:SLOT2:DATA DLIS *RST value is PN91125.5555.03 3.121 E-9
SOURce:NADC Subsystem<strong>SMIQ</strong>[:SOURce]:NADC:SLOT[:SOURce]:DATA:DLISt ‘name’The command selects a data list. This list will not be used unless it is set as a data source bymeans of the :NADC:SLOT:DATA DLIS command. This command triggers an event and hencehas no *RST value.Example: :NADC:SLOT:DATA:DLIS ’test’[:SOURce]:NADC:SLOT:SYNC #H0 to #HFFFFFFF (28 bit)The command changes the sync word predefined by the standard.Example: :SOUR:NADC:SLOT2:SYNC #HC7E3C0C *RST value depends on SLOT:TYPE[:SOURce]:NADC:SLOT:CDVCc #H1 to #HFFF (8 bit)This command sets the Coded Digital Verification Color Code.Example: :SOUR:NADC:SLOT2:CDVCc #H3F *RST value is 1[:SOURce]:NADC:SLOT:RSVD #H800 to #HFFF (12/11 bit)The command sets the reserved word (only for TCH and LINK DOWN). The MSBit is normallyset.Example: :SOUR:NADC:SLOT2:RSVD #H80F *RST value is #H8001125.5555.03 3.122E-9
Page 1:
Test and MeasurementDivisionOperati
Page 4 and 5:
Introduction on how to use the manu
Page 7 and 8:
Safety InstructionsWARNINGDanger of
Page 13 and 14:
ContentsSMIQ2.21 Arbitrary Waveform
Page 15 and 16:
ContentsSMIQ3 Remote Control.......
Page 17 and 18:
ContentsSMIQ3.7.4 Application of th
Page 19 and 20:
ContentsSMIQ5.3.9.2 AM Distortion .
Page 21 and 22:
ContentsSMIQC Annex C..............
Page 23 and 24:
ContentsSMIQFiguresFig. 1-1 SMIQ, v
Page 25 and 26:
ContentsSMIQFig. 2-81 Menu DIGITAL
Page 27 and 28:
ContentsSMIQFig. 2-168 DIGITAL STD
Page 29 and 30:
ContentsSMIQFig. 2-244 Menu MEM SEQ
Page 31 and 32:
Switchover to Remote ControlSMIQ3.1
Page 33 and 34:
MessagesSMIQ3.2.2 Remote Control vi
Page 35 and 36:
Structure and Syntax of the Device
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Description of CommandsSMIQ3.5 Desc
Page 43 and 44:
Description of CommandsSMIQ3.5.2 Co
Page 45 and 46:
Description of CommandsSMIQ*PRE 0 t
Page 47 and 48:
ARB SystemSMIQ3.5.4 ARB SystemRefer
Page 49 and 50:
ARB SystemSMIQ:ARB:WAVeform:FREE?Th
Page 51 and 52:
ARB SystemSMIQ:ARB:CLOCk:SOURce INT
Page 53 and 54:
ARB SystemSMIQ{CLOCK: frequency}(in
Page 55 and 56:
ARB SystemSMIQTo be read by the SMI
Page 57 and 58:
ARB SystemSMIQC-program for creatin
Page 59 and 60:
BERT SystemSMIQ3.5.5 BERT SystemCom
Page 61 and 62:
BERT SystemSMIQ:BERT:SETup:DENable
Page 63 and 64:
BLER SystemSMIQ3.5.6 BLER SystemCom
Page 65 and 66:
BLER SystemSMIQ:BLER:RESult?This co
Page 67 and 68:
CALibration SystemSMIQ:CALibration:
Page 69 and 70:
DIAGnostic SystemSMIQ3.5.8 DIAGnost
Page 71 and 72:
DIAGnostic SystemSMIQ:DIAGnostic:IN
Page 73 and 74:
FORMat SystemSMIQ3.5.10 FORMat Syst
Page 75 and 76:
OUTPut SystemSMIQ3.5.12 OUTPut Syst
Page 77 and 78:
OUTPut2 SystemSMIQ3.5.13 OUTPut2 Sy
Page 79 and 80:
SOURce:AM SubsystemSMIQ3.5.14.1 SOU
Page 81 and 82:
SOURce:CORRection SubsystemSMIQ[:SO
Page 83 and 84:
SOURce:DECT SubsystemSMIQCommand Pa
Page 85 and 86:
SOURce:DECT SubsystemSMIQ[:SOURce]:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
SOURce:DIST SubsystemSMIQ[:SOURce]:
Page 93 and 94:
SOURce:DIST SubsystemSMIQ[:SOURce]:
Page 95 and 96:
SOURce:DM SubsystemSMIQ[:SOURce]:DM
Page 97 and 98:
SOURce:DM SubsystemSMIQCommand Para
Page 99 and 100: SOURce:DM SubsystemSMIQ[:SOURce]:DM
Page 107 and 108: SOURce:FM SubsystemSMIQ3.5.14.6 SOU
Page 109 and 110: SOURce:FREQuency SubsystemSMIQ3.5.1
Page 111 and 112: SOURce:FSIM-SubsystemSMIQ3.5.14.8 S
Page 113 and 114: SOURce:FSIM-SubsystemSMIQ[:SOURce]:
Page 123 and 124: SOURce:GPS SubsystemSMIQ[:SOURce]:G
Page 125 and 126: SOURce:GSM Subsystem (Digital Stand
Page 131 and 132: SOURce:IS95 Subsystem (Digital Stan
Page 139 and 140: SOURce:LIST SubsystemSMIQ3.5.14.12
Page 141 and 142: SOURce:MARKer SubsystemSMIQ3.5.14.1
Page 143 and 144: SOURce:MODulation SubsystemSMIQ3.5.
Page 145 and 146: SOURce:NADC SubsystemSMIQCommand Pa
Page 147 and 148: SOURce:NADC SubsystemSMIQ[:SOURce]:
Page 149: SOURce:NADC SubsystemSMIQ[:SOURce]:
Page 153 and 154: SOURce:PDC SubsystemSMIQ3.5.14.17 S
Page 155 and 156: SOURce:PDC SubsystemSMIQ[:SOURce]:P
Page 163 and 164: SOURce:PHS SubsystemSMIQ3.5.14.19 S
Page 165 and 166: SOURce:PHS SubsystemSMIQ[:SOURce]:P
Page 171 and 172: SOURce:PM SubsystemSMIQ3.5.14.20 SO
Page 173 and 174: SOURce:POWer SubsystemSMIQ3.5.14.21
Page 175 and 176: SOURce:POWer SubsystemSMIQ[:SOURce]
Page 177 and 178: SOURce:ROSCillator SubsystemSMIQ3.5
Page 179 and 180: SOURce:SWEep SubsystemSMIQ[:SOURce]
Page 181 and 182: SOURce:WCDMa Subsystem (NTT DoCoMo/
Page 189 and 190: SOURce:W3GPp-SubsystemSMIQCommand P
Page 191 and 192: SOURce:W3GPp-SubsystemSMIQCommand P
Page 193 and 194: SOURce:W3GPp-SubsystemSMIQ[:SOURce]
Page 201 and 202:
SOURce:W3GPp-SubsystemSMIQ[:SOURce]
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
SOURce:W3GPp:ENHanced/OCNS/ADDition
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
SOURce2:FREQuency SubsystemSMIQ3.5.
Page 225 and 226:
SOURce2:MARKer SubsystemSMIQ3.5.15.
Page 227 and 228:
SOURce2:SWEep SubsystemSMIQ:SOURce2
Page 229 and 230:
STATus SystemSMIQ:STATus:OPERation:
Page 231 and 232:
SYSTem SystemSMIQ:SYSTem:BEEPer:STA
Page 233 and 234:
SYSTem SystemSMIQ:SYSTem:MSEQuence:
Page 235:
SYSTem SystemSMIQ:SYSTem:SERRor?Thi
Page 238:
SMIQTEST System:TEST:MCOD?The comma
Page 242 and 243:
SMIQTRIGger System:TRIGger:MSEQuenc
Page 244 and 245:
SMIQInstrument Model and Command Pr
Page 246 and 247:
SMIQInstrument Model and Command Pr
Page 248 and 249:
SMIQStatus Reporting SystemCONDitio
Page 250 and 251:
SMIQStatus Reporting System3.7.3 De
Page 252 and 253:
SMIQStatus Reporting System3.7.3.4
Page 254 and 255:
SMIQStatus Reporting System3.7.4 Ap
Page 256 and 257:
SMIQStatus Reporting System3.7.5 Re
Page 258 and 259:
SMIQFast Restore Mode3.8.2 Call-Up
Page 260 and 261:
SMIQMaintenance and Troubleshooting
Page 262 and 263:
SMIQTest Equipment and Test Assembl
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
SMIQPreparation, Recommended Test F
Page 270 and 271:
SMIQTest Procedures5.3.2.2 Settling
Page 272 and 273:
SMIQTest Procedures5.3.2.3 Setting
Page 274 and 275:
SMIQTest ProceduresRecommended test
Page 276 and 277:
SMIQTest ProceduresPassive measurem
Page 278 and 279:
SMIQTest Procedures5.3.4.4 Non-Inte
Page 280 and 281:
SMIQTest Procedures5.3.5.2 Subharmo
Page 282 and 283:
SMIQTest ProceduresNonharmonics of
Page 284 and 285:
SMIQTest Procedures5.3.5.5 SSB Phas
Page 286 and 287:
SMIQTest Procedures5.3.7 Internal M
Page 288 and 289:
SMIQTest Procedures5.3.8.3 Error Ve
Page 290 and 291:
SMIQTest Procedures5.3.8.6 I/Q Imba
Page 292 and 293:
SMIQTest Procedures5.3.9 Amplitude
Page 294 and 295:
SMIQTest Procedures5.3.10 Broadband
Page 296 and 297:
SMIQTest Procedures5.3.12.3 FM Freq
Page 298 and 299:
SMIQTest Procedures5.3.12.7 Level M
Page 300 and 301:
SMIQTest Procedures5.3.14.2 Analog
Page 302 and 303:
SMIQTest Procedures5.3.15 Data Gene
Page 304 and 305:
SMIQTest ProceduresSELECT CONTROL L
Page 306 and 307:
SMIQTest Procedures5.3.16 Digital S
Page 308 and 309:
SMIQTest ProceduresEDGE measurement
Page 310 and 311:
SMIQTest Procedures The adjacent-ch
Page 312 and 313:
SMIQTest Procedures5.3.17 IS-95 CDM
Page 314 and 315:
SMIQTest Procedures5.3.19 3GPP W-CD
Page 316 and 317:
SMIQTest Procedures Settings on dem
Page 318 and 319:
SMIQTest Procedures For 5 MHz offse
Page 320 and 321:
SMIQTest Procedures Channel table:-
Page 322 and 323:
SMIQTest ProceduresCHNO CHAN. CODE
Page 324 and 325:
SMIQTest Procedures Menu Select BS/
Page 326 and 327:
SMIQTest Procedures5.3.23.2 Additio
Page 328 and 329:
SMIQTest Procedures The result is a
Page 330 and 331:
SMIQTest Procedures5.3.23.6 Doppler
Page 332 and 333:
SMIQTest Procedures5.3.24.2 Additio
Page 334 and 335:
SMIQTest Procedures5.3.24.5 Signal/
Page 336 and 337:
SMIQTest Procedures5.3.24.6 Signal/
Page 338 and 339:
SMIQTest Procedures5.3.25 Arbitrary
Page 340 and 341:
SMIQTest Procedures5.3.25.4 Level D
Page 342 and 343:
SMIQTest ProceduresExample of a mea
Page 344 and 345:
SMIQPerformance Test ReportSection
Page 346 and 347:
SMIQPerformance Test ReportSection
Page 348 and 349:
SMIQIEC/IEEE Bus InterfaceAAnnex AA
Page 350 and 351:
SMIQIEC/IEEE Bus InterfaceA.1.4Inte
Page 352 and 353:
SMIQRS-232-C InterfaceA.2.2.1Transm
Page 354:
SMIQAsynchronous Interface SERDATAA
Page 357 and 358:
List of Error MessagesSMIQContinuat
Page 359 and 360:
List of Error MessagesSMIQDevice Sp
Page 361 and 362:
Page 363 and 364:
Page 366 and 367:
SMIQList of CommandsCAnnex CC.1 Lis
Page 368 and 369:
SMIQList of CommandsCommand Paramet
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
Page 376 and 377:
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Page 390 and 391:
SMIQProgramming ExamplesDAnnex DD.1
Page 392 and 393:
SMIQProgramming Examples6. List Man
Page 394:
SMIQProgramming ExamplesReading out
Page 397 and 398:
IndexSMIQvalue range ..............
Page 399 and 400:
IndexSMIQDisplaybrightness.........
Page 401 and 402:
IndexSMIQBIT CLOCK ................
Page 403 and 404:
IndexSMIQadditional................
Page 405 and 406:
IndexSMIQQAM modulation............
Page 407 and 408:
IndexSMIQbroadband AM..............
show all

Operating Manual R&S SMIQ - Volume 1 - Rohde & Schwarz

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?