Huntingdon 25-28-30-35-40 - The Fire Basket

Huntingdon 25-28-30-35-40Free Standing StoveInstructions for Use,Installation and ServicingFor use in GB & IE (Great Britain and Republic of Ireland).This appliance has been certified for use in countries other than those stated. To install this appliance in these countries, it is essential to obtain the translatedinstructions and in some cases the appliance will require modification. Contact Stovax for further information.IMPORTANTThis appliance will become hot whilst in operation, it is therefore recommended that a suitable guard should be used for theprotection of young children, the elderly or infirm. Do not attempt to burn rubbish in this appliance.Please read these Instructions carefully before installation or use.Keep them in a safe place for future reference and when servicing the fire.The commissioning sheet found on page 3 of these instructions should be completed by the Installer.PM228 ENG - Issue 3 (May 2011)

APPLIANCE COMMISSIONING CHECKLISTTo assist us in any guarantee claim please complete the following information.In the unlikely event of a problem, contact your installer or retailer for assistance.Retailer appliance was purchased fromName:..................................................................................................................................................................Address:...........................................................................................................................................................................................................................................................................................................................................Telephone number:..............................................................................................................................................Essential Information - MUST be completedDate installed:......................................................................................................................................................Model Description:..............................................................................................................................................Serial number:......................................................................................................................................................Installation EngineerCompany name:.....................................................................................................................................................................Address:.................................................................................................................................................................................................................................................................................................................................................................................Telephone number:................................................................................................................................................................Commissioning Checks (to be completed and signed)Is flue system correct for the appliance YES NOFlue swept and soundness test complete YES NOSmoke test completed on installed appliance YES NOSpillage test completed YES NOUse of appliance and operation of controls explained YES NOClearance to combustible materials checked YES NOInstruction book handed to customer YES NOSignature:........................................................................................Print name:...............................................................3

USER INSTRUCTIONSAIR CONTROLSMulti-fuel version Huntingdon 25 onlyWood-burning version Huntingdon 35/40 onlyAirwashcontrolClosedOpenAirwashcontrolOpenAirwashClosedMain doorcatchMain doorcatchRiddlingGratePrimaryControlOpenAshlipPR7222ClosedMulti-fuel version Huntingdon 28 onlyPR7533DOOR HANDLE1.13 Use a protected gloved hand to operate.See Diagram 3AirwashcontrolClosedOpenDO NOT OPEN THE DOOR WITH BARE HANDSMain doorcatchPrimaryControlAirwashcontrolMain doorcatchAshpandoor catchAshpandoorClosedOpenMulti-fuel version Huntingdon 30/35/40 onlyPrimary ControlClosedClosedOpenOpenPR7224RiddlingcontrolPR7223WARNINGDoor Handle:Pull forward to openAR2100Properly installed, operated and maintained, thisappliance will not emit fumes into the room.Occasional fumes from de-ashing and refuelling may occur.Persistent fume emission is potentially dangerous andmust not be tolerated.If fume emission does persist:—Open doors and windows to ventilate the room.—Leave the room.—Allow fire to burn out and safely dispose of fuel fromthe appliance.5

USER INSTRUCTIONS—Check for chimney blockage and clean if required.—Do not attempt to relight until the cause of the emissionhas been identified and correctedIf necessary seek expert advice.—All open flued appliances can be affected by temporaryatmospheric conditions which may allow fumes to enter thehouse. Because of this an electronic carbon monoxidedetector conforming to the latest edition of BSEN50291must be fitted in the same room as the appliance.The existence of an alarm must not be considered asubstitute for ensuring regular servicing and maintenanceof the appliance and chimney system.If the alarm sounds follow the instructions given underWarning above.2. USING THE Appliance FOR THE FIRSTTIME2.1 To allow the appliance to settle, and fixing glues and paintto fully cure, operate the appliance at a low temperature forfirst few days.• Dry cut wood for 12 to 18 months before usePoor quality timber:— Causes low combustion efficiency— Produces harmful condensation— Reduces effectiveness of the airwash and life of theapplianceDo not burn construction timber, painted, impregnated/ treated wood, manufactured board products or palletwood.3.2 Solid fuel:• Burn only anthracite or manufactured briquette smokelessfuels listed as suitable for use with closed heating appliancesDo not burn bituminous coal, ‘petro-coke’ or otherpetroleum based fuels as this will invalidate the productguarantee.3.3 Fuel consumption.As tested at nominal heat output to the requirements of EN13240: 2001 for intermittent operation:Fuel Consumption2.2 Do not touch the paint during the first period of use.2.3 During this time the appliance may give off someunpleasant odours. Keep the room well ventilated to avoid abuild-up of fumes.2.4 Please be aware that, during use, rope seals may discolour.This is normal.3.1 Wood Logs3. RECOMMENDED FUELSBurn only seasoned timber with a moisture content of lessthan 20%. To ensure this allow cut wood to dry for 12 to 18months.Wood LengthDescription70577058 Huntingdon 257058BL7058LG70647065 Huntingdon 287065BL7065LG7065PI70547055 Huntingdon 307055BL7055LG7055PIKg/hourWoodKg/hourBriquetteSmokeless fuel1.45 0.691.90 0.921.90 0.92ApplianceHuntingdon 25Huntingdon 28, 30Huntingdon 35Huntingdon 40Wood Length250mmm300mm350mm400mm7063 Huntingdon 35 (wood) 2.05 n/a70607061 Huntingdon 357061BL (multi-fuel)2.05 0.957061LG7061PI7069 Huntingdon 40 (wood) 2.66 n/a70747075 Huntingdon 407075BL (multi-fuel)7075LG7075PI2.66 1.266

USER INSTRUCTIONS5.3 Do not burn large amounts of fuel with the AirwashControl closed for long periods of time. This reduces theglass cleaning effect of the Airwash and causes tars andcreosotes to build-up in the appliance and flue system.5.4 When in use, burning the appliance at a high temperaturefor a short period reduces tars and creosotes.5.5 Experience establishes settings to suit personal preference.5.6 Burning Solid fuel:To burn smokeless fuels a cast iron multi-fuel kit must befitted. This kit also allows the efficient combustion of wood(see Installation Instructions, Section 4).• Set air controls, See Diagram 9(For individual model controls see diagrams on page 5)Air Wash: Fully OpenAir Wash: 50% Open5.11 Only anthracite or smokeless fuels suitable for use inclosed appliances must be burned in this appliance.5.12 Do not burn bituminous coal, ‘petro-coke’ or otherpetroleum based fuels as this invalidates the productguarantee.5.13 Do not load fuel above the log guard and the SecondaryAir Inlets at the back of the firebox (see Diagram 8).6. Burning tips6.1 Fuel Quality (Wood)Use wood with a moisture content of less than 20%.Seasoned logs have the bark beginning to lift and peel awayand cracks radiating from the centre. They feel lighter thanfresh cut wood of a similar size and sound hollow whenstruck against each other. Logs should not feel damp orhave moss or fungal growths.Symptoms related to wet wood:—Difficulty starting and keeping a fire burning well.—Smoke and small flames.—Dirty glass and/or Firebricks.—Rapid creosote build-up in the chimney.—Low heat output.—Short burn times, excessive fuel consumption and blue/grey smoke from the chimney.Burn at a high temperature for a short period each dayto avoid large build-ups of tars and creosotes within theappliance and the flue system.Primary Air: Fully OpenPrimary Air: 50% OpenAR20975.7 De-ash the firebed before re-fuelling (see User Instructions,Section 7).Open the Primary Air Control fully to establish a glowingbed before adding new fuel.Burn new fuel at a high temperature for a few minutesbefore adjusting the Primary Air Control to the desiredsetting.Refuel little and often for clean, efficient burning.5.8 Experience establishes settings to suit personal preference.5.9 Do not burn large amounts of fuel with the Primary AirControl on a low combustion setting for long periods oftime. This reduces the glass cleaning effect of the Airwashand causes tars and creosotes to build-up in the applianceand flue system.5.10 When in use, burning the appliance at a high temperaturefor a short period reduces tars and creosotes.Use Stovax Protector chimney cleaner to reduce thisproblem.6.2 Fuel Quality (Solid Fuel)Use recommended solid fuels approved for use with closedappliances.Symptoms related to unsuitable fuels include:—Difficulty starting and keeping a fire burning well.—Smoke and small flames.—Dirty glass and/or fire bricks.—Short life span for grate, baffles and internal firebricks.—Permanent staining of glass.6.3 Air inlets puffing smokeCombustion gases can build up in the firebox and igniteas small explosions, causing smoke to puff out of the airinlets and other openings. This occurs if the air controlsare shut soon after adding new fuel to a very hot fire. Stopby opening the air controls to increase combustion air andburning rate.CAUTION: Shutting down a hot appliance shortly afterrefuelling, and before the fire is established, could resultin poor combustion. This may lead to a build up ofunburned gases which could ignite noisily and, in extremecircumstances cause a small explosion and may damagethe appliance. Always maintain flames in the firebox whenthere is new fuel in the appliance - This is particularlyimportant when burning solid mineral fuels.8

USER INSTRUCTIONS6.4 Flue DraughtThe chimney has two main functions:1) To safely remove the smoke, gases and fumes from thehouse.2) To provide a sufficient amount of draught (suction) in theappliance ensuring the fire keeps burning.Draught is caused by the rising hot air in the chimney whenthe appliance is lit.Symptoms of poor performance related to flue draughtinclude:—Excessive fuel consumption (high flue draught).—Poor burning control and/or overheating (high fluedraught).—Wind noise from air controls (high flue draught).—Difficulty getting a fire going and keeping it burning well(low flue draught).—Low heat output (low flue draught).—Smoke entering room when doors are opened (low fluedraught).The construction, position, size and height of the chimneyall affect the performance of the flue draught.Other factors effecting the flue draught include:—Nearby trees or buildings causing turbulence.—Outside temperature.—Outside weather conditions.—Incorrect additional ventilation to building.—Blocked flue or chimney.For advice on the correction of persistent flue problemsconsult a qualified heating engineer before continuing touse the appliance.If the appliance emits smoke into the room continuously:—Close the air controls and allow the appliance to go out.—Ventilate the room to clear the fumes.Do not re-light the appliance until the problem is solved.7. ASH REMOVALDo not allow ash to build up as it may cause damageand adversely effect the performance of the appliance.Warning: Ash can remain hot long after appliance hasbeen in use.7.1 WoodAR2098—Open Doors, See Diagram 10.AR2184—Leave a layer of ash to start the new fire on. Wood burnsbest on a bed of ash (approx. 25mm (1") deep).— Remove Ashpan, See Diagram 116.5 Weather conditionsThe weather conditions outside the building can effect theburning performance of the appliance. These could include:Weather Conditions Problem EffectWindy daysBuildings/obstaclescause turbulent airaround chimneySmoky applianceCalm days Oversized chimney Smoky applianceDamp / Rainy daysFlue temperaturenot hot enough /rain water insidechimneyLighting andburning problemsTo reduce these problems:—Use good quality kindling wood to start the fire.—Burn initially at a high temperature for a short period.—Fit a rain cowl to the chimney.Your installer should advise you on possible solutions.AR2092AR2183—Remove ash with a small shovel and place into a StovaxAsh Caddy (Stovax Part No. 4227) or other suitablecontainer.Do not place hot ash in any container made from plasticor any other combustible material.—De-ash at least once a week.7.2 Multi-fuel:De-ash the appliance before filling with new fuel. Do notallow ash to build up on the underside of the grate as thiscan cause premature failure.9

USER INSTRUCTIONS—Insert the Riddling Tool into the socket as shown inDiagram 12.9.2 Over-firing can cause permanent damage to theappliance and invalid the product warranty.10. Chimney fire10.1 If a chimney fire occurs:—Shut all air controls immediately.—Evacuate the building.—Call the fire brigade.—Do not re-enter the building until it is confirmed safe.AR2088RiddlingHandleAR2186—Rotate the Riddling Tool backward and forward3 or 4 times to remove the ash. Do not force the handlebeyond its natural stop point. The ash will fall into theashpan.7.3 Open door(s).Warning: Ash can remain hot long after appliance hasbeen in use.Place the ash into a Stovax Ash Caddy (Stovax Part No.4227) or other suitable container.Check and remove ash as often as required when burningsolid fuel.De- ash at least once a week.Do not place hot ash in a container made from plastic orany other combustible material.8. Extended burning8.1 It is possible to get the appliance to burn for extendedperiods of time. In order to do this:—De-ash prior to final refuelling.—Set air controls to low combustion settings.This will gradually blacken the glass but it will clear whenoperated at a high temperature for a short period.10.2 Do not use the appliance after a chimney fire until:a) It has been inspected by a registered installer*,confirming the appliance is safe to use.b) The chimney system has been inspected and swept by achimney sweep, confirming the system is structurally soundand free from obstruction**.c) It is repaired as required before re-use. Use onlygenuine Stovax replacement parts to keep your appliance insafe, efficient working order.11. GENERAL CLEANING11.1 Clean and inspect the appliance regularly, especially inperiods of heavy use. Regular cleaning and maintenancewill help give many years of safe use.Allow appliance to cool thoroughly to avoid risk of burns.Clean regularly, according to level of use.Remove the ash completely (see User Instructions,Section 7).Check the internal components for damage (grates, bricks,baffles and log guard). Do not use the appliance if anyparts are broken or damaged. Replace damaged parts withgenuine Stovax replacement parts to keep the appliance insafe, efficient working order.Check for obvious build up of soot, ash or debris above theflue baffle(s) (these can be found in the upper part of thefirebox). Use a torch if necessary.—Use smokeless fuel or small, thick logs.9. OVER-FIRING9.1 Do not over-fill with fuel or run at high temperatures forlong periods or over-firing can occur. If the flue pipe, fluecollar or top plate glow red the appliance is over-firing.Close the air controls to reduce the temperature.In the U.K:* registered with HETAS (GB only)/INFO (Republic ofIreland only)**This should be done by a NACS registered (UK only)/INFO registered (Eire only) chimney sweep, who will issueyou with a certificate.10

USER INSTRUCTIONSIf there are any signs of a build up of debris above the fluebaffle(s) either:—Arrange for the chimney to be swept (see UserInstructions, Section 13).—Remove the baffles and clear the debris (see InstallationInstructions, Section 4).Clean matt black appliances using Stovax Colloidal black orStovax Grate Polish.To refresh painted finishes use Stovax Thermolac paint.Clean enamel finishes using warm soapy water and a softclean cloth.Wipe dry with a soft clean cloth be fore relighting. Alwaysdry appliance to avoid rust.Do not use abrasive cleaner or cleaning pads.Check that the door shuts properly and creates an effectiveseal. Leaking door seals prevent the appliance workingproperly.The above applies even if burning smokeless fuels.13.2 The chimney, any connecting flue pipe and the applianceflue ways, if incorporated, must be regularly cleaned.13.3 Ensure adequate access for cleaning where it is not possibleto sweep through the chimney.13.4 If the chimney is believed to have previously served anopen fire it must be swept a second time within a monthof regular use after installation.14. Care of stoveStovax has a range of cleaning and maintenance productsand accessories to keep your appliance in good workingorder. Your Stovax retailer can advise you on suitable itemsfor your stove and provide genuine spare parts such asreplacement glass, door sealing rope and firebricks. Viewthe extensive range at www.stovax.com by clicking onAccessories. In addition, an annual service by a competentengineer is recommended to keep your stove in the bestpossible condition.Do not use aerosol sprays near an operating appliance.12. CLEANING GLASSKeep the glass clean with correct use of the Airwash systemand good quality fuel.12.1 Sometimes additional cleaning may be required.This can be done as follows:—Allow appliance to cool fully. Do not clean hot glass.—Use a soft cloth and suitable cleaner.12.2 Do not use cleaning agents that have a high alkalinecontent, for example Stovax Gel Cleaner, on applianceswith painted glass such as the Studio, View or CL. Theseare abrasive cleaning agents that are designed to be usedwith heavily stained clear glass. Use Stovax Glass Cleaner(Stovax No.4103) on more delicate surfaces.12.3 Before re-lighting the appliance dry the glass fully.13. CHIMNEY SWEEPING13.1 To maintain safe and efficient use of the appliance, thechimney/flue must be inspected and swept at least once ayear by a qualified chimney sweep**.If the appliance is used continuously throughout the year,or it is used to burn wood or smokeless fuel, more frequentsweeping is recommended.The best time to have the chimney swept is at the start ofthe heating season.15. Seasonal use15.1 Clean and service the appliance if not used during warmermonths, as detailed in the Maintenance and Servicingsection.15.2 Set the air controls to 50% to keep the appliance ventilatedand stop the build-up of any moisture inside.15.3 Before re-lighting the appliance:—Remove the baffle(s).—Clear any debris that may have accumulated.—Check the flue is clear of any blockages.In the U.K:* registered with HETAS (GB only)/INFO (Republic ofIreland only)**This should be done by a NACS registered (UK only)/INFO registered (Eire only) chimney sweep, who will issueyou with a certificate.11

USER INSTRUCTIONS16. Troubleshooting tips16.1 Stove glass blackeningThis has four possible causes:1. Incorrect use of AirwashSee User Instructions, Sections 1, 4 and 5 for the correct useof the air controls.2. Burning unseasoned woodSee User Instructions, Section 3 to identify when wood isready for burning.3. Stove operated at too low a temperatureA stove pipe thermometer can identify this problem (Stovaxpart no 3046). The ideal working temperature range is130°C - 250°C (270°F - 480°F). Failing to close down thePrimary Air Control once the appliance has heated up tothis range may cause the appliance to exceed the idealtemperature range and to over-fire. Over-firing can causepermanent damage to the appliance and invalidates yourwarranty. Burn with the Airwash Control fully open forapproximately 20 minutes to cure this.16.5 Hinge Pin Riding UpThis occurs when the hinge block has moved out ofalignment. To correct this, adjust the hinge blocks back tothe vertical position (see Installation Instructions, Section 6).16.6 In the unlikely event of a problem that cannot be solvedby these tips contact your installer or retailer for help.17. SMOKE Control kit- huntingdon 25 only17.1 This appliance can be modified to burn wood in a smokecontrol zone. For more details on the Smoke Control Kit forthis appliance contact your retailer.NOTE: These appliances have been independently testedto PD6434 and approved by DEFRA as an exemptedappliance, allowing it to burn wood in Smoke Control areaswhen fitted with a Smoke Control Kit.The problem may be caused by damping down theappliance during periods of extended burning.4. Problems with the flue, in particular insufficient air pull.If the flue is not working efficiently the glass can blacken.A flue which has too much downdraft may be too short,needs lining, or has too many bends. This can also causeblackening of the stove glass. Contact the installer or a fluespecialist for advice.16.2 Glass crackingDo not over tighten the screws on the glass clips whenreplacing the glass. This causes stress and the intensetemperature changes can cause the glass to crack. Forreplacement glass contact your local Stovax retailer.16.3 Appliance is producing tarThis can be identified by:—A very strong pungent smell shortly after the appliance islit and heats up.—Glass blackening.—Thick, brown, sticky tar oozing from the pipe joints.This is caused by burning damp wood and running theappliance at too low a temperature.Use well seasoned wood and operate the appliance withinthe ideal temperature range.Tar is a major cause of chimney fires. If the applianceexperiences problems with tar build up consult a chimneysweep before continued use of the appliance.12

TECHNICAL SPECIFICATIONHUNTINGDONMODEL:Huntingdon 25 - 7057 / 7058 / 7058BL / 7058LGHuntingdon 28 - 7064 / 7065 / 7065BL / 7065LG/7065PIHuntingdon 30 - 7054 / 7055 / 7055BL / 7055LG /7055PIHuntingdon 35 - 7060 / 7061 / 7061BL / 7061LG / 7061PI/7063Huntingdon 40 - 7069 / 7074 / 7075 / 7075BL / 7075LG /7075PIHuntingdon 25Huntingdon 28Huntingdon 30Huntingdon 35Huntingdon 40Nominal Heat OutputWood kW 4.9 6.0 6.0 7.0 9.0Solid Fuel kW 4.9 6.0 6.0 7.0 9.0Flue Draught at Nominal Heat OutputAllmm Wg 1.25 1.25 1.25 1.25 1.25inch Wg 0.05 0.05 0.05 0.05 0.05Flue Gas Mass FlowFlue Gas Temperature at Spigot / SocketFlue Outlet Six (Top/Rear Option)Wood g/s 5.2 4.7 4.9 5.0 6.6Solid Fuel g/s 5.1 5.2 5.5 5.8 5.3Wood o C 310 405 405 360 380Solid Fuel o C 310 405 405 360 380mm 125 125 150 150 150inch 5 5 6 6 6Clearance to Combustible Materials Back mm 400 300 300 300 300Side mm 400 300 300 300 300Weight Kg 80 136 160 175 180Recommended FuelsWoodSolid FuelSeasoned wood (less than 20% moisture content)Briquette smokeless fuel suitable for closed appliances(Ancit-Phuracite-Taybrite-Homefire Ovals)Do not burn petroleum based fuels such as petro-coke, as these will seriously damage the appliance.As tested to the requirements of EN 13240 for intermittent operationNote: For efficiency and CO figures see the Declaration of Conformity at the rear of this manual.1. STANDARD FEATURES• Primary air (under grate air for full multi-fuel use) – (Multifuelappliances only)• Airwash (for wood burning / clean glass)• Preset secondary air control (to ensure complete burning offlue gases)• Riddling grate system for clean de-ashing – (Multi-fuelappliances only)• Top or rear flue exit option• Instructions• Guarantee card• Door handle tool• Flue collar• 4 X legs• Fire Cement*• Scraper** with Huntingdon 25 only2. PACKING LIST13

TECHNICAL SPECIFICATIONHUNTINGDON DIMENSIONSMulti-fuel versions only (30 / 35 / 40)PR7215Description Model A B C D E F (dia) G HHuntingdon 25Huntingdon 28Huntingdon 30Huntingdon 35705770587058BL7058LG706470657065BL7065LG7065PI705470557055BL7055LG7055PI7063706070617061BL7061LG7061PI590 452 357 130 445 125 145 45700 510 385 150 575 125 150 100592 553 397 150 469 150 150 105730 570 385 150 600 150 220 100Huntingdon 35 Short Leg 660 570 385 150 530 150 150 100Huntingdon 407069707470757075BL7075LG7075PI750 650 440 150 610 150 220 115Huntingdon 40 Short Leg 670 650 440 150 545 150 150 115All dimensions in mm. (25.4 mm = 1”)14

SITE REQUIREMENTS1. FLUE OR CHIMNEY1.1 The flue or chimney system must be in good condition.It must be inspected by a competent person and passed foruse with the appliance before installation.Products of combustion entering the room can causeserious health risks.1.2 The following must be checked:—The construction of the masonry chimneys, flue blockchimneys and connecting flue pipe system must meetthe requirements of the Building Regulations † .—A flexible flue liner system can be used if certified foruse with solid fuel systems and installation complies withmanufacturer’s instructions and Building Regulations † .The flue liner must be replaced when an appliance isreplaced, unless proven to be recently installed and ingood condition.—If it is necessary to fit a register plate it must conform tothe Building Regulations † .—The minimum height of the flue or chimney mustbe 4.5m from the hearth to the top of the flue, withno horizontal sections and a maximum of 4 bends.Bends must have angles of less than 45 degrees from thevertical.—Ensure the connecting flue pipe is kept a suitabledistance from any combustible material and does notform part of the supporting structure of the building.—Make provision to remove the appliance without theneed to dismantle the chimney.—Any existing flue must be confirmed as suitable forthe new intended use as defined in the BuildingRegulations † .—The flue or chimney systems must be inspected andswept to confirm the system is structurally sound andfree from obstructions**.—If the chimney is believed to have previously servedan open fire it must be swept a second time withina month of regular use after installation to clear anysoot falls that may have occurred due to difference incombustion levels.—The flue exit from the building must comply with localbuilding control rules † .—Do not connect or share the flue or chimney systemwith another heating appliance.1.3 Do not connect to systems containing large voids or spacesover 230mm square.1.4 Suitable access must be provided to enable the collectionand removal of debris.1.5 The flue must be swept and inspected when the applianceis installed.1.6 The flue draught must be checked with all windows anddoors closed and any extraction fans in this, or adjoiningrooms, running at maximum speed (see next section foradditional ventilation requirements).Max. Draught = 2.0mm WgMin. Draught = 1.0mm WgIn the U.K:* The latest edition of BS 6461: Part 1, and therequirements of Building Regulations**This should be done by a NACS registered (UK only)/INFO registered (Eire only) chimney sweep, who will issueyou with a certificate.† Building Regulations Document JFlue Plate:Where a hearth, fireplace, flue or chimney is providedor extended (including cases where a flue is providedas part of refurbishment work), information essentialto the correct appliance and use of these should bepermanently posted in the building, to meet RequirementJ4 of the Building Regulations (England and Wales), F3.12(Scotland).† Building Regulations Document JAdditional:A new factory made system that complies to the latest editionof EN 1856; Part 1 can be used providing installation is to therequirements of:i) the latest edition of BS 7566 Parts 1 -4ii) the manufacturer's instructionsiii) Building Regulations.For a guide containing information on Chimneys and Fluescontact:The British Flue & Chimney Manufacturers’ Association,FETA2 Waltham CourtMilley LaneHare HatchReadingBerkshire RG10 9THTel: 0118 9403416e-mail: info@feta.co.uk15

SITE REQUIREMENTS2. FLUE OUTLET POSITIONSThese positions are defined by Document J of the Building Regulations.Adjacent BuildingIMPORTANT: Seek specialistadvice if installing in a dwellingwith a thatched roofFlueTerminalHorizontalMeasurementVerticalMeasurement150mmmaxInsulationAdjacentBuildingThe datum for vertical measurement is the point ofdischarge of the flue from either the point of dischargeof the flue or 150mm above insulation, whichever isthe lower.Point where the flue passes through weather surface(Notes 1 &2)Clearances to flue outletA At or within 600mm of the ridge At least 600mm above ridgeB Elsewhere on roof (whether pitched or flat) At least 2300mm horizontally from the nearest point on the weather surface and:a) at least 1000mm above highest point of intersection of the chimney with andthe weather surface; orb) at least as high as the ridgeCBelow (on a pitched roof) or within 2300mm horizontally toopenable rooflight, dormer window, or other opening (Note 3)At least 1000mm above the top of openingDWithin 2300mm of an adjoining or adjacent building, whether ornot beyond the boundary (Note 3)At least 600mm above any part of the adjacent of building within 2300mmNotes:1) The weather surface is the building external surface, such as it's roof tiles or external walls.2) A flat roof has a pitch less than 10°.3) The clearance given for A or B, as appropriate, will also apply.4) A vertical flue fixed to an outside wall should be treated as equivalent to an inside flue emerging at the nearest edge of the roof.16

SITE REQUIREMENTS3. HEARTH DIMENSIONS4. Fitting Appliances on A boat4.1 If an appliance is to be fitted in a boat it must be done inaccordance with the latest edition of BS 8511 (Code ofPractice for the Installation of Solid Fuel Heating Applianceson Boats). The Code covers the design, installationand operation of solid fuel heating appliances that aresuitable for fitting into inland waterway boats, and givesguidance on product selection, design considerations,installation requirements, inspection and testing, as well asmaintenance and safe use tips.4.2 Consideration should also be given to the requirements ofthe Boat Safety Scheme (BSS) to ensure the boat's insuranceremains valid.150mmminimum225mmminimumConstructional Hearth840mm minimum150mmminimum150mmminimumConstructional Hearth840mm minimumPR72163.1 The appliance must stand on a non-combustibleconstructional hearth which is at least 125mm thick withthe minimum dimensions as shown in diagram.3.2 If this appliance can be installed in an elevated setting itis recommended to increase the 225mm hearth depth tosafely contain any falling logs or embers. The higher theappliance is installed the deeper the hearth should be toavoid scorched floor coverings.4.3 The appliance should only be installed by a competentperson with experience of the latest edition of BS 8511 andthe Boat Safety Scheme (BSS).4.4 Secure the product to a suitably constructed noncombustiblehearth.4.5 All open flued appliances can be affected by temporaryatmospheric conditions which may allow fumes to enter theboat. An electronic carbon monoxide detector conformingto the latest edition of BSEN50292 must be fitted andmaintained.4.6 Failure to safely install the appliance could endanger theboat and persons on board.3.3 The building must have a suitable load-bearing capacity forthe hearth and appliance. Consult a structural engineerfor advice before proceeding.3.4 When fitting into an existing hearth check that the hearthcomplies with current construction regulations and is atleast the minimum sizes shown.3.5 If there is no existing fireplace or chimney it is possible toconstruct a suitable non-combustible housing and hearthsetting. The flue must be installed in accordance with alllocal and national regulations and current rules in force.3.6 Check if adding a new chimney to your property requiresplanning permission.17

SITE REQUIREMENTS5. WALLS NEXT TO A HEARTHSolid, non-combustiblematerial e.g. masonryor concreteThickness WH150mmminimumCC150mmminimumPR7217Position of Appliance & Hearth in relation to wallsRequirement for the wallsDistance of hearth from wall'C'Distance of Appliance to wallMin thickness of Wall'W'Min height of wall'H'0mm0mm0mm - 50mm51mm - 300mm200mm75mmHeight of appliance + 300mmOr1200mm from the hearth (take largestdimension)0 - 150mm 150mm + 75mm 1200mm150mm + 300mm + No Minimum RequirementSuitable clearance should be allowed around the stove to enable the correct fitting and maintenance of the appliance.Any clearances should be confirmed by making a site survey and a physical check of wall thickness and dimensions.18

PRE-INSTALLATION CHECKS1. FlueMODEL:Huntingdon 25 - 7057 / 7058 / 7058BL / 7058LGHuntingdon 28 - 7064 / 7065 / 7065BL / 7065LG/7065PIHuntingdon 30 - 7054 / 7055 / 7055BL / 7055LG/7055PIHuntingdon 35 - 7060 / 7061 / 7061BL / 7061LG /7061PI/7063Huntingdon 40 - 7069 / 7074 / 7075 / 7075BL / 7075LG/7075PIHuntingdon 25Huntingdon 28Huntingdon 30Huntingdon 35Huntingdon 40Flue/Chimney SizeFlue/Chimney(*minimum height)Without flue linerRound (diameter)Without flue linersystem Square(diameter)With liner or Factorymade system (diameter)installed in accordance with manufacturer'sinstructionsAll productsmm 150 150 150 150 150inch 6 6 6 6 6mm 135 135 135 135 135inch 5 1 / 2 5 1 / 2 5 1 / 2 5 1 / 2 5 1 / 2mm †150 †150 150 †150 150inch †6 †6 6 †6 6metre 4.5 4.5 4.5 4.5 4.5feet 15 15 15 15 15* When measured from the top of the stove to the top of the flue, with nohorizontal sections and a maximum of 4 bends with angles of less than 45 o†May be 125mm (5") if only burning low volatiles (smokeless) fuels approved for use in Smoke Control Areas.See web sit http://uksmokecontrolareas.co.uk for more information about approved fuel2. Ventilation2.1 This appliance requires a constant supply of air to maintainproper combustion and effective flue performance.2.2 An inadequate air supply can result in poor combustion andsmoke entering the room which is potentially dangerous.2.3 This supply of air can come from either:—The natural leakage of air into the room in which theproduct is fitted.—Purpose provided ventilation.—Some Stovax appliances can also be fitted with anoptional outdoor air kit which allows air to be drawn infrom the outside.2.4 The amount of air required must comply with local buildingregulations and the rules in force.2.5 If spillage is detected during commissioning then there maybe insufficient natural ventilation and an additional air supplywill be necessary.2.6 Many older buildings are sufficiently ventilated by naturalleakage of air to provide suitable air supply for an applianceof 5kW output or less.Modern building techniques have reduced the amount of airthat leaks in or out of a house. A modern construction withan air tightness of less than 5m 3 per hour per m 2 requires anair vent for ALL solid fuel appliances including those with arated heat output of less than 5kW.NOTE: The air leakage of a modern house is tested at thecompletion of construction and a certificate issued confirmingthis.2.7 Ventilation requirements in the UK are as shown in the tablebelow:A) Traditionally Built Homes• Where the leakage is greater than 5m 3 /hour/m 2 .• Ventilation normally required = 550mm 2 per kW outputover 5kW19

PRE-INSTALLATION CHECKSOutput (kw) 4 5 6 7 8 9 10mm 2 None None 550 1100 1650 2200 2750A Additionalventilationcm 2 None None 5.50 11.0 16.5 22.0 27.5in 2 None None 0.89 1.77 2.66 3.55 4.40B) Modern Construction Homes• Where the leakage is less than 5m 3 /hour/m 2 .• Ventilation normally required = 550mm 2 per kWOutput (kw) 4 5 6 7 8 9 10mm 2 2200 2750 3300 3850 4400 4950 5500B Additionalventilationcm 2 22.0 27.5 33.0 38.5 44.0 49.5 55.0in 2 3.55 4.40 5.32 6.21 7.10 7.99 8.872.8 Permanent air vents should be non-adjustable and positionedwhere they are unlikely to be become blocked.2.9 If vents open into adjoining rooms or spaces there must be anair vent of at least the same size direct to the outside.2.10 Site the vents where cold draught is unlikely to causediscomfort. This can be avoided by placing vents near ceilingsor close to the appliance, see diagram.2.11 Extractor fans or cooker hoods must not be placed in thesame room or space as this can cause the appliance to emitfumes into the room.2.12 Increase air supply provisions where a room contains multipleappliances.2.13 If any checks reveal problems do not proceed with thefitting of the appliance until they have been rectified.20

INSTALLATION INSTRUCTIONSLegal requirementsAssemble the appliance by attaching the legs to the base ofthe appliance, Diagram 1Before installation and/or use of this appliance please readthese instructions carefully to ensure that all requirements arefully understood.Bolts to adjustlevelsThe appliance must be fitted by a registered installer*, orapproved by your local building control officer.It is very important to understand the requirements of the nationalBuilding Regulations † and standards‡, along with any localregulations and working practices that may apply. Should anyconflict occur between these instructions and these regulationsthen the regulations must apply.Your local Building Control Office can advise regarding therequirements of the regulations.The appliance must be fitted by a registered installer* or approvedby your local building control officer.Works must be carried out with care to meet the requirementsof Health and Safety** and comply with the Health and Safetyrules**, and any new regulations introduced during the lifetime ofthese instructions. Particular attention should be drawn to:Screws tosecure legsChoose top or rear flue exit:TopHexagonalboltsAR2094—Handling: The appliance is heavy. Adequate facilitiesmust be available for loading, unloading and on sitehandling.—Fire Cement: Some fire cement is caustic and must notcome into contact with the skin. Protective gloves mustbe worn. Wash hands thoroughly with plentyof water after contact with skin.—Asbestos: This appliance contains no asbestos. If thereis the possibility of disturbing any asbestos in the courseof installation seek specialist guidance and useappropriate equipment.—Metal Parts: Take care when installing or servicing thestove to avoid personal injury.RearFit flue collar and blanking plate to suit.AR2086Attach flue collar to top or rear with hexagonal bolts (seePicture 2).Seal with fire cement.Secure blanking plate with clamping bar, Diagram 3A faulty installation can cause danger to the inhabitants andstructure of the building.For users of this appliance:Your building insurance company may require you to inform themthat a new heating appliance has been installed on your property.Check that your cover is still valid after installing the appliance.1. INSTALLING THE ApplianceEach installation is unique to the property so it is not possibleto give details to suit every setting. The installation must complywith Building Regulations † and be made using best practiceconstruction methods.Many fireplace openings have a supporting lintel. Do not removewithout supporting the remaining structure of the building. Do notsupport the structure with the appliance or the flue system.1.1 Take care when installing the appliance. Carelesshandling and use of tools can damage the finish and/orarea.AR2096† England and Wales – Document J / Scotland - Part F/Document J (Republic of Ireland only)‡ the latest edition of BS 8303, BS EN 15287, BS 7566*Registered on the Competent Persons Scheme (GB only)see page 26 / INFO (Republic of Ireland).**Health and Safety at Work Act 197421

INSTALLATION INSTRUCTIONS1.2 Top flue pipe installation:—Lift appliance into place, taking care not to damagehearth finish.—Level appliance using adjustable bolts (see Diagram 1).—Connect appliance to the chimney using flue pipe.—Secure with self tapping screw.—Seal the connecting joints.Seal Collar with Fire CementSelf Tapping ScrewTeeSize Stovax Part No.5" 4516*6" 4616CapPR7218The Flue must be installed in accordance withmanufacturers instructions.AR8009Flue Pipe 915mm (3ft)SizeStovax Part No.*5" 45026" 4602Self tappingscrew at rear600mm min1000mm maxunsupportedTo chimney connectionas detailed in buildingregulationsElbow with access coverSizeStovax Part No.5" 4512*6" 4612Flue Pipe 915mm (3ft)SizeStovax Part No.5" 4502*6" 4602Seal flue collarwith Fire CementPR72201.3 Rear flue pipe installation:—Insert a tee into the flue collar.The tee piece is used as cleaning access.AR7219—Lift appliance into position, taking care not to damagethe hearth finish.—Level using adjustable bolts (see Picture 1).—Secure with self tapping screw.—Seal the connecting joints.Do not use a 90˚ elbow to make this connection.The Flue must be installed in accordance withmanufacturers instructions.2. REMOVAL OF THE LOG GUARD2.1 To remove the log guard:—Lift log guard clear of the supporting brackets.—Rotate to clear the sides of the door opening.Do not use appliance without the log guard in position.3. FITTING AND REMOVAL OFTHE FIREBRICKS3.1 Remove the firebricks as part of routine maintenance. Notools are required.3.2 Allow the appliance to cool fully before removing firebricks.3.3 Take care when handling as bricks can become fragile afteruse. Life span depends on the type of fuels burnt and thelevel of use.Replace damaged bricks as soon as possible.22

INSTALLATION INSTRUCTIONS3.4 To remove bricks:HUNTINGDON 25—Remove side bricks—Slide rear bricks forward to removeHUNTINGDON 28, 30 & 35—Lift top LH brick and remove top RH brick—Remove top LH brick—Remove side bricks—Remove back brickHUNTINGDON 40—Pull the base of a side brick towards the centre of thestove and repeat for the opposite side—Remove rear brickFor All Models:—Replace in reverse order4. FITTING AND REMOVAL OFTHE BAFFLESHUNTINGDON 40—Repeat the instructions given under paragraph 3.4 toremove the bricks—Lift the LH baffle bricks as high and as far forward aspossible—Slide the RH baffle brick under the LH brick and lowerinto stove—Repeat for the LH brickFor All Models:—Replace in reverse order5. FITTING AND REMOVAL OFTHE RIDDLING MECHANISMThe following applies to the Multi-fuel versions only.5.1 The riddling mechanism can be removed for cleaning tomaintain good working condition.Huntingdon 25 and 28 versions4.1 The appliance is fitted with a baffle in the top of thefirebox to maintain efficient combustion.4.2 Allow the appliance to cool fully before removing bafflesystem.4.3 Remove the log guard from the appliance to give access tothe firebox.4.4 Take care when handling the bricks; they can becomefragile in time. This is normal and wear depends on thetype of fuels burnt and the level of use.IMPORTANT—Remove and clean the baffle system to ensure the flueways are clear of soot and debris and to ensure the safeand efficient operation of the stove—Frequency of cleaning depends on the operatingconditions—Replace any damaged baffles immediatelyStationaryRiddlingMechanismHuntingdon 30, 35 and 40 versionsMovingRiddlingMechanismAR2185StationaryRiddlingMechanismDO NOT MODIFY THE BAFFLE SYSTEMHUNTINGDON 25—Remove the baffle—Lift the baffle plate—Rotate it and slide it out through the frontMoving Riddling MechanismTo remove Riddling Mechanism:—Lift the moving and stationary grate parts, Diagrams5 - 7AR2087HUNTINGDON 28, 30 & 35—Repeat the instructions given under paragraph 3.4above to remove the bricks. These bricks form the baffle23

INSTALLATION INSTRUCTIONSRiddling bar7. ADJUSTING DOOR catch7.1 The door catch can be adjusted to ensure safe correctclosing of the door. This is completed by:—Clean parts.AR2089—Replace parts ensuring that raised sections of riddlingbar are upright and the grooves on the moving parts arefitted over it correct, Diagrams 7 and 8.—Loosen the catch fixing screw—Move the catch position to suit the door catch/handleThe catch can be moved in/out using the Jacking Screw(2.5mm key)—Tighten the fixing screwsAn adjustable stop is provided to stop the door hittingthe side of the appliance. This prevents damage to theenamel (10mm A/F Spanner)This may require a trial and error approach to find thecorrect position.MovingRiddling BarStationaryRiddling BarAR20956. ADJUSTING DOOR & Ashpan HINGESFixingsJackingScrews6.1 The door and Ashpan hinges can be adjusted to ensuresafe, correct closing of the door.— Loosen the hinge fixing screws— Move the hinge position— Tighten the fixing screwsThis may require a trial and error approach to find thecorrect positionFixingScrewsAdjustablestopAR2093NoteEnamel stoves: Protect the lower edge of the door and lip plate.8. co alarmsAll open flued appliances can be affected by temporaryatmospheric conditions which may allow fumes to enterthe house. Building regulations require that whenevera new or replacement fixed solid fuel or wood/biomassappliance is installed in a dwelling a carbon monoxidealarm must be fitted in the same room as the appliance.Further guidance on the installation of the carbonmonoxide alarm is available in the latest edition ofBS EN 50292 and from the alarm manufacturer'sinstructions.Provision of an alarm must not be considered asubstitute for either installing the appliance correctlyor ensuring regular servicing and maintenance of theappliance and chimney system.AR209924

COMMISSIONING1.1 To commission:COMMISSIONING—Replace the baffle and log guard.—Check the door alignment and catch operation andadjust if required (see Installation Instructions, Section 5).—Check the soundness of door seals, castings and joints.—Check the operation of the air controls.1.2 Now carry out a final smoke draw test:—Explain the requirement to use a suitable fireguardwhen children, elderly or infirm persons are near theappliance.—Record retailer/supplier and installer details inAppliance Commissioning Checklist (page 3,Instructions for Use).—Record serial number in Appliance CommissioningChecklist (page 3, Instructions for Use).This number is required when ordering spare parts andmaking warranty claims.—Give this instruction manual to the customer.—Warm the flue with a blowlamp, or similar, for about 10minutes.—Place a smoke pellet on the centre of the grate, with theair controls open.—Close the door. Smoke should now be drawn up the flueand be seen to exit from the flue terminal.—Complete test with all doors and windows closed in theroom where the appliance is fitted.—If there are any extractor fans in adjacent rooms the testmust be repeated with the fans running on maximumand with interconnecting doors open.—Check the effect of ceiling fans during the test.If the test fails, re-check the suitability of the flue systemand ventilation. An inadequate air supply to the room ispotentially dangerous.—Light the appliance and slowly increase the temperature.—Ensure no combustion products enter the room.—Open the main fire door when the appliance reachesoperating temperature and carry out a spillage test witha smoke match or pellet around the door opening.1.3 If excessive spillage occurs allow the appliance to cool andre-check the flue system and ventilation.1.4 Finally:—Explain to the user the safe operation of theappliance, use of the controls and the importance ofonly using suitable fuels.—Ensure that a CO alarm has been fitted and make theuser aware of its operation and importance, referringthem to the Warning section on page 5 of the UserInstructions.—Explain the cleaning and routine maintenancerequirements.25

MAINTENANCE and SERVICINGFor a complete list of spare parts and accessories contact your Stovax or call 01392 4740111. ANNUAL SERVICE1.1 Before the start of the heating season strip, inspect andclean the appliance as detailed:—Allow appliance to cool.—Remove all internal parts; baffle, log guard and, formulti-fuel versions, grate system and ashpan(see Installation Instructions, Sections 2, 3 & 4). Take carehandling firebricks as they can become fragileafter a period of use.—Sweep the flue at this point if necessary.—Vacuum clean any remaining ash and debris from theinside of the appliance. Stovax offer a filter/collectionattachment for vacuum cleaners to protect them from fireash: Ash Clean (Stovax Part No. 2091).—Clean the internal surfaces of the appliance using awire brush and scraper as required. Vacuum and brushthe resulting debris from the appliance.—Clean the grate parts with a wire brush, and check theparts for any damage. Replace any damaged parts usinggenuine Stovax replacements parts (see belowfor details).—Check and clean the firebricks with a soft brush.Some surface damage will occur during use. The life ofthe bricks will depend on the type of fuels burnt and thelevel of use. Replace damaged bricks as soon as possible.—Re-fit cleaned internal parts.TaskGlass cleaningPreventing buildupof creosote influeSealing flue pipejointsRe-paintingCleaning mattblack AppliancesProtecting yourhandsDoor sealing ropeGlass sealing tapeProduct nameStove glass cleaner(spray on)Stovax CodeNumber4103Protector (15 sachets) 7002Protector (1kg tub) 7025Fire Cement (500g tub) 2020Fire Cement (600g cartridge) 2021Thermolac Black(400ml aerosol)Thermolac Black(200ml brush-on)Ivory Paint(400ml aerosol)201920572055Colloidal black (85ml) 7000Heat resistant leather gloves 400814mm Black rope seal(handy pack)14mm Black rope seal(25m reel)3mm Black rope seal(handy pack)3mm Black rope seal(25m reel)5000467049754974—Remove glass from door, discard all old rope seals and fitnew (see Maintenance and Servicing, Section 4).—Do not use cleaning agents that have a high alkalinecontent, for example Stovax Gel Cleaner, on applianceswith painted glass such as the Studio, View or CL. Theseare abrasive cleaning agents that are designed to be usedwith heavily stained clear glass. Use Stovax Glass Cleaner(Stovax No.4103) on more delicate surfaces.Do not use acidic cleaners on printed glass.—Fit new door rope seal (see Maintenance and Servicing,Section 5).—Lightly oil the door catch mechanism and hinge pins.Avoid getting oil onto the door seals and glass.—To refresh painted finishes use Stovax Thermolac paint.1.2 Use genuine Stovax replacement parts to keep theappliance in safe, efficient working order. This is a list of themaintenance products that may need be required:Thermic seal glue (50ml bottle) 5037Soft rope 10mm diameter 4965Ash Clean Vacuum Cleaner Attachment 2091These products, available from your local Stovax retailer,along with regular maintenance and use of correct fuels, willkeep the appliance in the best possible condition.1.3 For more information about the Stovax Group productsplease visit our web site at www.stovax.com1.4 Burn at a low temperature for the first day of use after anymaintenance. This allows the seals, fixing glues and paint tofully cure.1.5 During this time the appliance may give off someunpleasant odours. Keep the room well ventilated to avoida build-up of fumes.1.6 Your Stovax retailer can carry out service and maintenance.26

MAINTENANCE and SERVICING2. REMOVAL OF THE LOG GUARD2.1 To remove the log guard:—Lift log guard clear of the supporting brackets.—Rotate to clear the sides of the door opening.Do not use appliance without the log guard in position.3. FITTING AND REMOVAL OF THEFIREBRICKS3.1 See Installation Instructions, Section 3.3.2 Take care when handling as bricks can become fragile afteruse. Life span depends on the type of fuels burnt and thelevel of use.4. FITTING AND REMOVAL OF BAFFLE(S)4.1 See Installation Instructions, Section 4.4.2 It is important to remove and clean the baffle system toensure the flue ways are clear of soot and debris andto ensure the safe, efficient operation of the stove. Thefrequency of cleaning depends on the stove operatingconditions.4.3 The baffle system is designed to give safe and efficientoperation of the stove. Replace any damaged bafflesimmediately.4.4 Do not modify the baffle system.5. REMOVAL OF RIDDLING MECHANISM5.1 The riddling mechanism can be removed for cleaning tomaintain good working condition.See Section 5, Installation Instructions, to remove andreplace the riddling mechanism.6. FITTING A NEW DOOR GLASSALL MODELSTo maintain safe use of the appliance damaged door glassmust be replaced immediately. To do this:—Remove the door by opening, removing the hinge pinsand lifting the door free of the hinge blocks.—Lay the door face down on a soft flat surface to protectthe paintwork and glass.—Remove the glass fixing clips and screws. The old glasscan then be lifted clear of the door.Note how the 3mm sealing rope is placed between theglass and the door.—Dispose of the old glass safely.—Clean and re-paint the rear of the door if required.—Clean the screws with light oil and coat with hightemperature anti-seize grease to aid future removal.—Fit a new sealing rope and place the glass into positionin the door.—Place the glass fixing clips into position and re-fix withthe clean fixing screws, tightening the screws evenly untilglass is held securely (see Diagram 1).Do not over tighten the screws as this could break theglass.6.2 Fit only original Stovax ceramic glass, which is suitable touse in high temperature applications.6.3 Using the appliance with damaged door glass could causedangerous fumes to enter the room or the appliance toover-fire resulting in damage.7. fitting a new door sealALL MODELS5.1 To maintain the safe use of the appliance damaged or worndoor sealing rope must be replaced. To do this:—Remove door from appliance by opening, removing thehinge pins and lifting the door free of the hinge blocks.—Lay the door face down on a soft, flat surface to protectthe paintwork and glass.—Remove old rope and scrape old glue from locatinggroove.—Clean the locating groove with a clean, dry cloth toremove all old dust and debris.—Squeeze a generous bead of fresh Stovax Thermic Sealglue into the rope locating groove.—Press the new Stovax rope into the locating groove,placing the joint in the middle of the lower edge of thedoor.—Refit door and close to apply pressure to new rope.—Leave the door(s) closed for at least 12 hours beforelighting the appliance and run at a low temperature forapproximately one day. This allows the adhesive to fullybond to the seal.5.2 Using the appliance with a damaged door seal can causedangerous fumes to enter the room, or the appliance toover fire resulting in damage.27

MAINTENANCE and SERVICING8. ADJUSTING DOOR & Ashpan HINGES8.1 See Installation Instructions, Section 6.Your Stovax retailer can carry out your service andmaintenance requirements.9. ADJUSTING DOOR catch9.1 The door catch can be adjusted to ensure safe correctclosing of the door.See Installation Instructions, Section 7.10. CLEANING IVORY STOVES8.1 Huntingdon appliances with the Ivory effect require specialattention when cleaning as they have been coated with ahigh quality paint that should give many years of service.However this colour will mark more easily and requirecleaning more than other models.Take care when touching the stove to avoid wiping ash andsoot into the paint. Most marks can be removed using amild soap solution and a clean lint free cloth.The finish can also be refreshed using the aerosol touchup paint (product code 2055) available from your Stovaxretailer.Allow appliance to cool thoroughly to avoid risk of burns.Organisations authorised to certify competence in theinstallation of domestic solid fuel appliances(Competent Persons Scheme):APHC - Association of Plumbing and HeatingContractors (Certification) Ltd.www.aphc.co.ukBESCA - Building Engineering Services CompetenceAccreditation Ltd.www.besca.org.ukHETAS - Heating Equipment Testing and ApprovalScheme Ltd.www.hetas.co.ukNAPIT - National Association of Professional Inspectorsand Testers Ltd.www.napit.org.ukNICEIC - NICEIC Group Ltd.www.niceic.org.ukHETAS Approved Chimney Sweeps:Nacs - The National Association of Chimney Sweepswww.chimneyworks.co.ukAPICS - The Association of Master Chimney Sweeps Ltd.www.apics.orgGMS - The Guild of Master Chimney Sweepsguildofmasterchimneysweeps.co.ukINFO - Irish National Fireplace Organisationwww.fireplace.ie28

BASIC SPARE PARTS LIST25113107124968113141529

BASIC SPARE PARTS LISTHuntingdon 25 Huntingdon 28 Mk1 Huntingdon 28 Mk2Diagram Description Part No.Diagram Description Part No.Diagram Description Part No.No.No.No.1 Door Glass GL02601 Door Glass GL01031 Door Glass GL01032 Baffle DV-761402 Baffle LH HUM28.72 Baffle LH HUM28.73 Inner back plate DV-083312 Baffle RH HUM28.62 Baffle RH HUM28.64 Grate Holder DV-611113 Rear Fire Brick HUM28.33 Rear Fire Brick HUM28.35 Side Fire brick DV-77333.04 Grate Base Plate HUM28.554 Grate Base Plate HUM28.556 Ashpan DV-052205 Side Fire brick LH HUM28.45 Side Fire brick LH HUM28.47 Ashpan handle DV-SLT55 Side Fire brick RH HUM28.55 Side Fire brick RH HUM28.58 Glass Retainer DV-W/015/E6 Ashpan HUM28.366 Ashpan HUM28.369 Glass Retainer Screw DV-W/018/E10 Log Retainer HUM28.2810 Log Retainer HUM28.2810 Log Retainer DV-Z/2517/G11 Centre Grate BR5211 Centre Grate BR5211 Centre Grate DV-6111112 Riddling Rod HUM28.5612 Riddling Rod HUM28.5612 Riddling Rod DV-61309.015 Implement Tool HUM2715 Implement Tool HUM27N/A Glass Clip HUM42N/A Glass Clip HUM42N/A Door Pin HUM35N/A Door Pin HUM35Huntingdon 30 Huntingdon 35 MK1 Huntingdon 35 MK2Diagram Description Part No.Diagram Description Part No.Diagram Description Part No.No.No.No.1 Door Glass GL02381 Door Glass GL01051 Door Glass GL01052 Baffle LH H30.72 Baffle LH H35.72 Baffle LH H35.72 Baffle RH H30.62 Baffle RH H35.62 Baffle RH H35.63 Rear Fire Brick H30.33 Rear Fire Brick H35.33 Rear Fire Brick H35.34 Grate Base Plate HUM28.555 Side Fire brick LH H35.45 Side Fire brick LH H35.45 Side Fire brick LH H30.45 Side Fire brick RH H35.55 Side Fire brick RH H35.55 Side Fire brick RH H30.56 Ashpan H35.366 Ashpan H35.366 Ashpan H30.3610 Log Retainer H35.2810 Log Retainer H35.2810 Log Retainer H30.2813 Riddling Grate Top HUM35.3813 Riddling Grate Top HUM35.38N/A Glass Clip HUM4214 Riddling Grate Bottom HUM35.4014 Riddling Grate Bottom HUM35.40N/A Door Pin HUM35N/A Glass Clip HUM42N/A Glass Clip HUM42N/A Door Pin HUM35N/A Door Pin HUM3515 Implement Tool HUM2715 Implement Tool HUM27Huntingdon 40 MK1Diagram Description Part No.No.1 Door Glass GL01042 Baffle LH HUM72 Baffle RH HUM65 Side Fire brick LH HUM45 Side Fire brick RH HUM56 Ashpan HUM3610 Log Retainer HUM2813 Riddling Grate Top HUM3814 Riddling Grate Bottom HUM40N/A Glass Clip HUM42N/A Door Pin HUM3515 Implement Tool HUM27Huntingdon 40 MK2Diagram Description Part No.No.1 Door Glass GL01042 Baffle LH HUM72 Baffle RH HUM63 Rear Fire Brick HUM35 Side Fire brick LH HUM45 Side Fire brick RH HUM56 Ashpan HUM3610 Log Retainer HUM2813 Riddling Grate Top HUM3814 Riddling Grate Bottom HUM40N/A Glass Clip HUM42N/A Door Pin HUM3515 Implement Tool HUM27A30

SERVICE RECORDS1ST SERVICEDate of Service:...........................................................................Next Service Due:.......................................................................Signed:........................................................................................Dealer's Stamp/HETAS Registration Number2ND SERVICEDate of Service:...........................................................................Next Service Due:.......................................................................Signed:........................................................................................Dealer's Stamp/HETAS Registration Number3RD SERVICEDate of Service:...........................................................................Next Service Due:.....................................................................Signed:........................................................................................Dealer's Stamp/HETAS Registration Number4TH SERVICEDate of Service:...........................................................................Next Service Due:.......................................................................Signed:........................................................................................Dealer's Stamp/HETAS Registration Number5TH SERVICEDate of Service:...........................................................................Next Service Due:.......................................................................Signed:........................................................................................Dealer's Stamp/HETAS Registration Number6TH SERVICEDate of Service:............................................................................Next Service Due:.......................................................................Signed:........................................................................................Dealer's Stamp/HETAS Registration Number7TH SERVICEDate of Service:...........................................................................Next Service Due:.......................................................................Signed:........................................................................................Dealer's Stamp/HETAS Registration Number8TH SERVICEDate of Service:...........................................................................Next Due:........................................................................Signed:........................................................................................Dealer's Stamp/HETAS Registration Number9TH SERVICEDate of Service:...........................................................................Next Due:........................................................................Signed:........................................................................................Dealer's Stamp/HETAS Registration Number10TH SERVICEDate of Service:...........................................................................Next Service Due:.......................................................................Signed:........................................................................................Dealer's Stamp/HETAS Registration Number31

Stovax Ltd, Falcon Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7LFTel: (01392) 474011 Fax: (01392) 219932 E-mail: info@stovax.com www.stovax.com