HX8218-C01 - All Shore Industries
HX8218-C01 - All Shore Industries HX8218-C01 - All Shore Industries
HX8218-C01960CH TFT LCD Source Driver with TCON5.10 Standby ON/OFF ControlDATA SHEET V04HX8218-C01 has a power ON/OFF sequence control function. When STB pin ispulled L, blank data is outputted for 5-frames first, from the falling edge of thefollowing VSYNC signal. The blank data would be gray level 255 for normally whiteLC.Figure 5. 7 Standby ON/OFF ControlHimax ConfidentialThis information contained herein is the exclusive property of Himax and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Himax. Subject to change without notice.-P.21-October 2006
HX8218-C01960CH TFT LCD Source Driver with TCON6. DC CharacteristicsDATA SHEET V046.1 Absolute Maximum Rating (GND=VSS=0V)ParameterSymbolSpec.Min. Typ. Max.UnitPower supply voltage 1 VCC -0.3 - +7.0 VPower supply voltage 2 VDD -0.3 - +7.0 VLogic Output Voltage V OUT -0.3 - +7.0 VInput voltage Vin -0.3 - VDD+0.3 VOperation temperature T OPR -40 - +85 ℃Storage temperature T STG -55 - +125 ℃Note: (1) All of the voltages listed above are with respective to GND=VSS=0V.(2) Device is subject to be damaged permanently if stresses beyond those absolute maximum ratings listedabove.6.2 DC Electrical Characteristics (GND=VSS=0V, TA=25 ℃ )Parameter SymbolSpec.Min. Typ. Max.Unit ConditionPower supply voltage VCC 3 3.3 3.6 V -Power supply voltage VDD 3.8 5 5.5 V -Low level input voltage V IL 0 - 0.3VCC V -High level input voltage V IH 0.7VCC - VCC V -Output low voltage V OL 0 - 0.2VCC V I OL =400µAOutput high voltage V OH 0.8VCC - VCC V I OH =-400µAInput leakage current I IN -1 - +1 µA No pull up or pull down.Output voltageQA/QB/QC1 ~ 320,VdeviationVD - ±20 - mVV IN =0.1~4.9V,DC offset V OS - - ±20 mVQA/QB/QC1 ~ 320,V IN =0.1~4.9V,Output leakage current I O -1 - +1 µAQA/QB/QC1 ~ 320 at highimpedancePull high resistance R H 150 200 250 kΩRESETB,STB,ZX1~3,VSETPull low resistance R L 150 200 250 kΩDEN,IF[2:1],MOD,CF[2:1],Dx[7:0],OSD_R,OSD_G,OSD_B,OSD_ENOutput current I OH 20 40 - µAQA/QB/QC1 ~ 320,V O =4.9V vs. 4.0V, VDD=5VOutput current I OL 20 40 - µAQA/QB/QC1 ~ 320,Vo=0.1V vs. 1.0V, VDD=5VAnalog operatingfIcurrentDD - - 6 mA CLK =27MHz, f IHS =15.7KHz,VDD=5V, CL=60pFDigital operating current I CC - - 11 mAf CLK =27MHz, f IHS =15.7KHz,VCC=3.3VAnalog standby current I VDD - - 2 mA All LCD outputs are High-Z.Digital standby current I VCC - 16 50 µAAll inputs are stopped andoutputs are High-Z.Himax ConfidentialThis information contained herein is the exclusive property of Himax and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Himax. Subject to change without notice.-P.22-October 2006
- Page 1 and 2: ( DOC No. HX8218-C01-DS )HX8218-C01
- Page 3 and 4: HX8218-C01960CH TFT LCD Source Driv
- Page 5 and 6: HX8218-C01960CH TFT LCD Source Driv
- Page 7 and 8: HX8218-C01960CH TFT LCD Source Driv
- Page 9 and 10: HX8218-C01960CH TFT LCD Source Driv
- Page 11 and 12: HX8218-C01960CH TFT LCD Source Driv
- Page 13 and 14: HX8218-C01960CH TFT LCD Source Driv
- Page 15 and 16: HX8218-C01960CH TFT LCD Source Driv
- Page 17 and 18: HX8218-C01960CH TFT LCD Source Driv
- Page 19 and 20: HX8218-C01960CH TFT LCD Source Driv
- Page 21: HX8218-C01960CH TFT LCD Source Driv
- Page 25 and 26: HX8218-C01960CH TFT LCD Source Driv
- Page 27 and 28: HX8218-C01960CH TFT LCD Source Driv
- Page 29 and 30: HX8218-C01960CH TFT LCD Source Driv
- Page 31 and 32: HX8218-C01960CH TFT LCD Source Driv
- Page 33 and 34: HX8218-C01960CH TFT LCD Source Driv
- Page 35 and 36: HX8218-C01960CH TFT LCD Source Driv
- Page 37 and 38: HX8218-C01960CH TFT LCD Source Driv
- Page 39 and 40: HX8218-C01960CH TFT LCD Source Driv
- Page 41 and 42: HX8218-C01960CH TFT LCD Source Driv
- Page 43 and 44: HX8218-C01960CH TFT LCD Source Driv
- Page 45 and 46: HX8218-C01960CH TFT LCD Source Driv
- Page 47 and 48: HX8218-C01960CH TFT LCD Source Driv
<strong>HX8218</strong>-<strong>C01</strong>960CH TFT LCD Source Driver with TCON5.10 Standby ON/OFF ControlDATA SHEET V04<strong>HX8218</strong>-<strong>C01</strong> has a power ON/OFF sequence control function. When STB pin ispulled L, blank data is outputted for 5-frames first, from the falling edge of thefollowing VSYNC signal. The blank data would be gray level 255 for normally whiteLC.Figure 5. 7 Standby ON/OFF ControlHimax ConfidentialThis information contained herein is the exclusive property of Himax and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Himax. Subject to change without notice.-P.21-October 2006