TMS2000 - OEC Fluid Handling, Inc.

More documents

Recommendations

Info

INSTRUCTION MANUALTMS2000IMPORTANT! TMS2000 SENSOR WIRING INSTRUCTIONSIDENTIFY THE TYPE OF SENSOR(S) TO BE INSTALLED. WIRING MUST BETERMINATED ON THE TERMINALS INDICATED BELOW TO ENSURE CORRECTOPERATION OF SENSORS.SENSORWIRING1 + V2 S13123456123GND+S1GNDV+S2GND+V1 V2 S13123456+GND+VS1GND+ VS2GNDVS1GNDREDBLKREDBLKWHTBLKGRNGRNREDBLKREDWHTBLKHS100LS600LS610RSU801HS100DRSU800(NON-DISCRIMINATING)RSU800(DISCRIMINATING)ES825-100(F)ES825-200(F)SENSORMODELPNEUMERCATORLiquid Level Control SystemsBULLETIN 173 REV. N/C 05/09/02 120 FINN COURT FARMINGDALE, N.Y. 11735PAGE 1 OF 1Figure 3-8 - TMS2000 sensor wiringTMS2000 Installation.doc 07-11-05PAGE 31
INSTRUCTION MANUALTMS20003.4 PROGRAMMABLE RELAY OUTPUTS/CONTACT CLOSURE INPUTSThe TMS2000 provides dry contact closure inputs and relay contact closure outputs that areuser-programmable via the console front panel or most TMS communications interfaces. Each inputis programmable for relay control and alarm functions as well as remote relay acknowledgement orgating functions. Inputs may also be programmed to monitor submersible pump or generator activityin conjunction with the TMS Series AUTO LEAK TEST mode. Each relay output is programmable totrigger on any combination of events, including in-tank leak, theft, product or water setpoints, leak orpoint level sensor alarm, contact closure input or system error. Additionally, relays are individuallyprogrammable for failsafe mode; delayed shutoff mode and a latching mode for pump up/downfunctions. Typical relay applications include remote annunciation, pump and siphon break/flowcontrol valve operation, and other user-defined switch closure inputs. These relays also provide asimple and straightforward interface to most programmable logic controllers, building managementsystems, and similar input monitoring devices.The standard TMS2000 includes two (2) dry contact closure inputs and two (2) relay contact closureoutputs as illustrated in Figure 3-9 below. Also shown is an optional 4 Input/4 Relay Output Card.An optional 8 Input/8 Relay Output Card or 16 Relay Output Card is available.CAUTIONRelay output and contact closure input terminals are located on theNON-INTRINSICALLY SAFE side of the console. ALL wiring to these terminalsMUST enter through the designated conduit opening. Refer to FIGURE 1-3.FAILURE TO COMPLY MAY RESULT IN PERSONAL INJURY, PROPERTY LOSSAND EQUIPMENT DAMAGE.OPTIONAL RELAYCARDRELAY OUTPUTSCONTACTCLOSURE INPUTSSTANDARDRELAY OUTPUTSSTANDARD CONTACTCLOSURE INPUTSDRAWING NO. 20051 REV. N/CFigure 3-9 - Relay Output/Contact Closure Input Layout(Optional 4 Relay Output/4 Contact Closure Input Expansion Card shown)TMS2000 Installation.doc 07-11-05PAGE 32
Page 1 and 2: Telephone 800-500-9311Telephone 864
Page 3 and 4: INSTRUCTION MANUALTMS2000Note: A se
Page 5 and 6: Liquid Level Control SystemsPAPERFE
Page 7 and 8: INSTRUCTION MANUALTMS2000The consol
Page 9 and 10: INSTRUCTION MANUALTMS20001.4 LIQUID
Page 11 and 12: INSTRUCTION MANUALTMS2000SECTION 2
Page 13 and 14: INSTRUCTION MANUALTMS20002.3 LEVEL
Page 15 and 16: INSTRUCTION MANUALTMS2000Install th
Page 17 and 18: INSTRUCTION MANUALTMS20002.4.2 BUSH
Page 19 and 20: INSTRUCTION MANUALTMS20004. Tighten
Page 21 and 22: INSTRUCTION MANUALTMS20002.7 LEAK S
Page 23 and 24: INSTRUCTION MANUALTMS20004. Feed th
Page 25 and 26: INSTRUCTION MANUALTMS2000BLK WHTRED
Page 27 and 28: INSTRUCTION MANUALTMS2000CABLE SELE
Page 29 and 30: INSTRUCTION MANUALTMS20003.2 POWER
Page 31 and 32: INSTRUCTION MANUALTMS2000WIRE SPLIC
Page 33: INSTRUCTION MANUALTMS2000WIRE SPLIC
Page 37 and 38: INSTRUCTION MANUALTMS20003.6 PROBE

TMS2000 - OEC Fluid Handling, Inc.

Create successful ePaper yourself

Delete template?

Save as template?