TMS2000 - OEC Fluid Handling, Inc.

More documents

Recommendations

Info

GRNINSTRUCTION MANUALTMS20003.3 PROBE/SENSOR WIRING & SPLICES.IMPORTANT! PROBE WIRING INSTRUCTIONS - MODELS TMS2000 AND TMS3000TMS CONSOLETYPICAL WIRING FOR TMS CONSOLES! WARNINGRefer to TMS installation manual forWARNINGS and CAUTIONS beforeproceeding. FAILURE TO COMPLYMAY RESULT IN PERSONAL INJURY,PROPERTY LOSS AND EQUIPMENTDAMAGE.NON-INTRINSICALLY SAFE WIRINGINTRINSICALLY SAFE WIRINGPROBE MODELSCOVERED BY THIS BULLETINMP461SCMP450SMP451SMP452SMP461SVMP462SVMP463SVNON-HAZARDOUS AREAHAZARDOUS AREACLASS 1, GROUPS C,D3/4" NPT (TMS2000)1" NPT (TMS3000)OR EQUIVALENTCONDUIT FITTINGWIRE SPLICE SEAL CONNECTOR (BY PCO *)FOLLOW SUPPLIED WIRE SPLICE INSTRUCTIONSBULLETIN 179; KIT P/N 10585-2 (FOR MP46xS)BULLETIN 181; KIT P/N 10585-2L (FOR MP45xS)1/2" NPT OR EQUIV. CABLE GRIPREQ'D ONLY ON MP45xS MODELS(JUNCTION BOX MOUNTS DIRECTLYTO PROBE ON MP46xS MODELS)REDBLKSHDPROBE 1+VGNDSHIELD+VGNDSHIELDPROBE 2REDBLKSHDTMS2000 PROBE INPUT WIRING TMS3000 PROBE INPUT WIRINGWIRING MUST BE DONE IN WATERTIGHT RATED BOX/HOUSINGCHANNEL1PROBESENSORS+VGNDSHDGNDSIG+V+VFIELD WIRING CABLE (BY CUSTOMER)EXAMPLE: BELDEN 8441, AVAILABLEFROM PCO * AS CW1-0500 (500' SPOOL)12TYPICALTANKW/ PROBEFROMPROBECONDUIT AND VAPOR SEAL FITTING(SIZE AND LOCATION TO BEDETERMINED BY QUALIFIED INSTALLER) REDUCER FITTING(IF NEEDED)BLKJUNCTION BOX(PROVIDED BYINSTALLER)MP46xSMP45xSPNEUMERCATORBulletin 199 Rev. N/C (07/13/05) Liquid Level Control SystemsPage 1 of 1TOREDFIELD CABLENote for all probe models:Conductor colors may varydepending on cable manufacturer.The field cable shield wire mustbe connected to the PROBESHIELD TERMINAL in the consoleI.S. compartment and should be cutback and left unterminated at theprobe junction box.BLKTOWHTTOGNDSTUDTO CONSOLE(AS SHOWN ABOVE)BLKTOBLKTOREDRED* "PCO" REFERS TO PNEUMERCATOR COMPANY.7/13/2005 2:40:12 PM, 1:1, © COPYRIGHT 2005 PNEUMERCATOR COMPANY, INC.Figure 3-4 - MP45xS Cable Splice and WiringTMS2000 Installation.doc 07-11-05PAGE 27
INSTRUCTION MANUALTMS2000WIRE SPLICE AND SEAL INSTRUCTIONS - 2 CONDUCTOR PAIRS KIT 10585-2LWARNING: USE CONNECTORS ONLY FOR THEIR DESIGNATED PURPOSE. DO NOT USE FOR AC WIRING.1BREAK APART 2 STRIP WIRESFIELD CABLE *(2) "V" SLOTS1.25".75"OUTERSLEEVEUSE TO SEAL MP45xPROBE CABLE SPLICESINNERSLEEVEMP45x PROBECABLE* PROBE FIELD CABLE SHIELD WIRE HAS NO CONNECTION1.25".75"SPLICE SEAL WIRE CONNECTOR PROVIDED BY PNEUMERCATOR34STRIP GREEN WIRE AS NEEDED TOCONNECT TO JUNCTION BOX GROUND STUDGREENGROUND WIREBEND OVERGROUND WIREAS SHOWN5TWIST WIRES (EXCEPT FOR GND WIRE)6INSERTSNAP ON OUTER SLEEVEDO NOT REUSEPULL ONE TWISTED LEAD PAIRTHROUGH EACH "V" AND BEND OVERCONNECT GND WIRETO JUNCTION BOXGND STUDPNEUMERCATORBulletin 181 Rev. B (02/09/05)Liquid Level Control SystemsPage 1 of 12/9/2005 6:02:06 PM, 1:1, © COPYRIGHT 2005 PNEUMERCATOR COMPANY, INC.Figure 3-5 - MP45xS Splice Kit InstructionsTMS2000 Installation.doc 07-11-05PAGE 28
Page 1 and 2: Telephone 800-500-9311Telephone 864
Page 3 and 4: INSTRUCTION MANUALTMS2000Note: A se
Page 5 and 6: Liquid Level Control SystemsPAPERFE
Page 7 and 8: INSTRUCTION MANUALTMS2000The consol
Page 9 and 10: INSTRUCTION MANUALTMS20001.4 LIQUID
Page 11 and 12: INSTRUCTION MANUALTMS2000SECTION 2
Page 13 and 14: INSTRUCTION MANUALTMS20002.3 LEVEL
Page 15 and 16: INSTRUCTION MANUALTMS2000Install th
Page 17 and 18: INSTRUCTION MANUALTMS20002.4.2 BUSH
Page 19 and 20: INSTRUCTION MANUALTMS20004. Tighten
Page 21 and 22: INSTRUCTION MANUALTMS20002.7 LEAK S
Page 23 and 24: INSTRUCTION MANUALTMS20004. Feed th
Page 25 and 26: INSTRUCTION MANUALTMS2000BLK WHTRED
Page 27 and 28: INSTRUCTION MANUALTMS2000CABLE SELE
Page 29: INSTRUCTION MANUALTMS20003.2 POWER
Page 33 and 34: INSTRUCTION MANUALTMS2000WIRE SPLIC
Page 35 and 36: INSTRUCTION MANUALTMS20003.4 PROGRA
Page 37 and 38: INSTRUCTION MANUALTMS20003.6 PROBE

TMS2000 - OEC Fluid Handling, Inc.

Create successful ePaper yourself

Delete template?

Save as template?