TMS2000 - OEC Fluid Handling, Inc.

More documents

Recommendations

Info

INSTRUCTION MANUALTMS20005. Pull properly marked 2 to 4 conductor wiring (depending on probe/sensor configuration) for eachprobe/sensor through the conduit leaving at least 24 inches excess at both console and junctionbox ends for final connections. The field wires must be resistant to hydrocarbon liquids; typeTHHN or MTW, 22 AWG is recommended. Use Belden Cable part number 8441, or equivalent2-conductor shielded cable, for the magnetostrictive probes only. This cable can be supplied byPNEUMERCATOR as part number CW1-0500.6. Fill all conduit VAPOR SEAL-OFF FITTINGS with approved filling compound and tighten allconduit fittings.7. Splice all probe/sensor wires to the respective conduit wires at each WATERTIGHT JUNCTIONBOX. (See Figure 3-4 for a recommended procedure). Maintain correct color-coding and polaritybetween wires.8. Connect probe/sensor wires to the TMS2000 INPUT TERMINALS following Figure 3-1. Maintaincorrect polarity between wires and respective terminal points.9. Probes and sensors should be logically identified as to location and type and recorded on theprobe map provided in this manual, SECTION 3.6.CAUTIONProbe and sensor wires are to be connected ONLY to the designated inputterminals of the INTRINSIC SAFETY compartment. Do NOT allow probe/sensorwires to cross over into the non-intrinsically safe section. FAILURE TOCOMPLY MAY RESULT IN PERSONAL INJURY, PROPERTY LOSS ANDEQUIPMENT DAMAGE.TMS2000 Installation.doc 07-11-05PAGE 25
INSTRUCTION MANUALTMS20003.2 POWER WIRING INSTALLATION.PARTIAL VIEW OF A TYPICALSERVICE PANELPARTIAL VIEW OF TMSBREAKER 3 BREAKER 4BREAKER 2BREAKER 5BREAKER 1BREAKER 6HOTNEUTGNDISGNDISGNDLINE 1 BUSSBARGND BUSS BARLINE 2 BUSSBARNEUTRALBUSS BARNOTE:ALL TMS GROUNDS MUST BE TERMINATED AT THE GND BUSS BAR IN THE SAME SERVICEPANEL AS TMS POWER. A GROUNDING ROD, COLDWATER PIPE OR OTHER CONNECTIONSHOULD NOT BE USED.PNE UMER CATOR COMPANYLiquid Level C ontrol S ystems120 FINN COURT FARMINGDALE, N.Y. 11735BULLETIN 172 TMS SERIES GROUND WIRINGREV. N/C (03/29/02) PAGE 1 OF 1Figure 3-3 - TMS AC Power WiringTMS2000 Installation.doc 07-11-05PAGE 26
Page 1 and 2: Telephone 800-500-9311Telephone 864
Page 3 and 4: INSTRUCTION MANUALTMS2000Note: A se
Page 5 and 6: Liquid Level Control SystemsPAPERFE
Page 7 and 8: INSTRUCTION MANUALTMS2000The consol
Page 9 and 10: INSTRUCTION MANUALTMS20001.4 LIQUID
Page 11 and 12: INSTRUCTION MANUALTMS2000SECTION 2
Page 13 and 14: INSTRUCTION MANUALTMS20002.3 LEVEL
Page 15 and 16: INSTRUCTION MANUALTMS2000Install th
Page 17 and 18: INSTRUCTION MANUALTMS20002.4.2 BUSH
Page 19 and 20: INSTRUCTION MANUALTMS20004. Tighten
Page 21 and 22: INSTRUCTION MANUALTMS20002.7 LEAK S
Page 23 and 24: INSTRUCTION MANUALTMS20004. Feed th
Page 25 and 26: INSTRUCTION MANUALTMS2000BLK WHTRED
Page 27: INSTRUCTION MANUALTMS2000CABLE SELE
Page 31 and 32: INSTRUCTION MANUALTMS2000WIRE SPLIC
Page 33 and 34: INSTRUCTION MANUALTMS2000WIRE SPLIC
Page 35 and 36: INSTRUCTION MANUALTMS20003.4 PROGRA
Page 37 and 38: INSTRUCTION MANUALTMS20003.6 PROBE

TMS2000 - OEC Fluid Handling, Inc.

Create successful ePaper yourself

Delete template?

Save as template?