TMS2000 - OEC Fluid Handling, Inc.

More documents

Recommendations

Info

INSTRUCTION MANUALTMS2000FAX/MODEMCARD(OPTIONAL)REVISIONSREV DESCRIPTIONDATEAPPROVEDLISTED INDICATOR MODEL NUMBERMODEL TMS 2000APPROV ALS DATER. KHARE 091297DO NOT SCAL E DRAWI NGPNEUMERCATOR COMPANY120 FINN COURT FARMINGDALE, N.Y. 11735INTRINSICALLY SAFE LOOPMODEL TMS 20004787650253SIZE CAGE CODE DWG. NO. REV.DSCALE NONESHEET2 OF 2NON-INTRINSICALLYSAFE WIRINGINTRINSICALLY SAFEWIRING (SEE SHT. 1)RELAY I/ORJ-11JACKS (3)RS-232 COMMUNICATIONSRS-485 TO PCO PERIPHERALSTELEPHONE LINEDRY CONTACT SWITCH OUTPUT (SEE NOTE 10)NON-I.S. DRY CONTACT INPUTNON-HAZARDOUSAREA(SEE NOTE 1)HAZARDOUS AREACLASS I, GROUPS C,DINDICATORINTRINSICALLY SAFEWIRING COMPARTMENTCARD120 VAC(+10%,60Hz)TO EARTH GROUND (SEE NOTE 3)-(OPTIONAL)(SEE NOTE 11)NOTES - NON-INTRINSIC SAFETY10. DRY CONTACT SWITCH OUTPUT WIRING: WIRE TO COMMON AND EITHERNORMALLY OPEN OR NORMALLY CLOSED FOR DESIRED SWITCH CONTACT.OUTPUT RATED 10 AMPS AT 120 VAC, 6 AMPS AT 240 VAC. (VOLTAGEMUST BE LESS THAN 120 VAC OR 240 VAC RESPECTIVELY).11. NEC CLASS 2 CIRCUITS.A 041299C REMOVE SHEET 3, ADD MODEL 2A-F070901REMOVE CABLE REFERENCES AND P/N'SMP451,461,462,463 ES825-100FD REMOVE NOTES 5-8 071301DFigure 3-1b - Non-Hazardous Wiring DiagramTMS2000 Installation.doc 07-11-05PAGE 23
INSTRUCTION MANUALTMS2000CABLE SELECTION GUIDE FOR INTRINSIC SAFETYGROUP C GROUP DTOTAL LENGTH CHANNEL MAXIMUM TOTAL LENGTH CHANNEL MAXIMUMTYPE MANUFACTURERS FEET LENGTH FEET FEET LENGTH FEET___(SEE NOTE 2)___ BELDEN ALPHA COLOR CODE ___(SEE NOTE 3)___ ___(SEE NOTE 4)___ ___(SEE NOTE 3)___ ___(SEE NOTE 4)___MAG.PROBEMP450, MP460(PAT,7100 series)S 8441 - BLK / RED 5300 3000 12000 3000S 8761 2401C BLK / CLR 9200 4600 16000 4600S 82761 -BLK / RED 9200 4600 16000 4600S, B 83552 - BLK / WHT 6000 3000 12000 30003-WIRE OPTO-SENSORES825 series, ES820-100(ELS-1100)NS 8443 1173C BLK / RED / GRN (BELDEN) 2700 2700 11300 5500BLK / RED / WHT (ALPHA)S 9608 6327 BLK / RED / WHT 2600 2600 11000 5500S - 2403C BLK / RED / WHT 3800 3800 16000 5500S, B 83553 - BLK / REDIWHT 2700 2700 11000 55004-WIRE OPTO SENSORES820-200(ECS-1100)NS 8444 1174C BLK / RED / WHT / GRN 2700 2700 11300 5500S 9609 6328 BLK / RED / WHT / GRN 2600 2600 11000 5500S - 2404C BLK / RED / WHT / GRN 4000 4000 16000 6500S, B 83554 - BLK / RED / WHT / GRN 2800 2800 11000 5500NOTES:1.) ALL CABLES SPECIFIED HAVE A NOMINAL PAIR INDUCTANCE OF 0.2uH / FT.2.) TYPE SPECIFIERSNS = NON-SHIELDEDS = SHIELDEDB = DIRECT BURIAL (IF ALLOWABLE PER LOCAL CODES)3.) TOTAL LENGTH:MAG. PROBES – TOTAL COMBINED CABLE LENGTH FOR ALL MAG. PROBESLEAK SENSORS – TOTAL COMBINED CABLE LENGTH FOR ALL LEAK SENSORS4.) CHANNEL MAXIMUM LENGTH: MAXIMUM CABLE LENGTH PER MAG. PROBE OR SENSOR.5.) FOR OPTO-SENSORS, SHIELDED CABLE IS NOT REQUIRED, BUT IF USED IN THEAPPLICATION, THE SHIELD MUST BE CONNECTED TO “SHD” TERMINAL IN CONSOLE I.S.COMPARTMENT. Figure 12C-Wiring Chart.eps 07-05-05Figure 3-2 - Instrinsically Safe Cable Selection GuideTMS2000 Installation.doc 07-11-05PAGE 24
Page 1 and 2: Telephone 800-500-9311Telephone 864
Page 3 and 4: INSTRUCTION MANUALTMS2000Note: A se
Page 5 and 6: Liquid Level Control SystemsPAPERFE
Page 7 and 8: INSTRUCTION MANUALTMS2000The consol
Page 9 and 10: INSTRUCTION MANUALTMS20001.4 LIQUID
Page 11 and 12: INSTRUCTION MANUALTMS2000SECTION 2
Page 13 and 14: INSTRUCTION MANUALTMS20002.3 LEVEL
Page 15 and 16: INSTRUCTION MANUALTMS2000Install th
Page 17 and 18: INSTRUCTION MANUALTMS20002.4.2 BUSH
Page 19 and 20: INSTRUCTION MANUALTMS20004. Tighten
Page 21 and 22: INSTRUCTION MANUALTMS20002.7 LEAK S
Page 23 and 24: INSTRUCTION MANUALTMS20004. Feed th
Page 25: INSTRUCTION MANUALTMS2000BLK WHTRED
Page 29 and 30: INSTRUCTION MANUALTMS20003.2 POWER
Page 31 and 32: INSTRUCTION MANUALTMS2000WIRE SPLIC
Page 33 and 34: INSTRUCTION MANUALTMS2000WIRE SPLIC
Page 35 and 36: INSTRUCTION MANUALTMS20003.4 PROGRA
Page 37 and 38: INSTRUCTION MANUALTMS20003.6 PROBE

TMS2000 - OEC Fluid Handling, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?