TMS2000 - OEC Fluid Handling, Inc.

More documents

Recommendations

Info

INSTRUCTION MANUALTMS2000ASSEMBLY INSTRUCTIONS - DIRECT MOUNTED MODEL MP45xSApplies to the following installations;• Probe lengths exceeding 15 feet .• Chemical, solvent or heated tanks using standard PVC leader cable.• Pressurized tanks. Consult with Technical Support for pressure limits.Questions? Contact Technical Support at (800) 209-78581FOR INSTALLATION AND WIRING SEE TMS MANUALThe top of the probe is an ungageable deadband. Verify that theprobe is of sufficient length so that the float's magnet will not travelinto this deadband.PROBE HEAD8"24" DIRECT MOUNTING ASSEMBLYSTANDARD APPLICATIONSSTANDARD APPLICATIONS2" DIRECT MOUNTING ASSEMBLYCHEMICAL APPLICATIONSWITH INTERFACE WITHOUT INTERFACE WITHINTERFACEWITHOUTINTERFACECOMPRESSION *FITTING2" X 3/4" NPT *BUSHINGCOMPRESSION *FITTING2" X 3/4" NPT *BUSHING4" X 2" NPTBUSHING(by customer)PRODUCTFLOATPRODUCTFLOATOPTIONALINTERFACEFLOATINTERFACEFLOATMETAL WEIGHTS.S. COLLARFLUSH WITH BOTTOMOF PROBE SHAFT1/2"S.S. COLLARMETAL WEIGHTCATHODICBOOTCATHODICBOOTSPACERRETAININGRINGEND CAPRETAININGRINGEND CAP* PURCHASED SEPARATELY FROM PNEUMERCATOR AS MODEL NO. PK2-DMx.PNEUMERCATORLiquid Level Control SystemsBulletin 165 Rev. B (08/10/04) Page 1 of 1Figure 2-6 - MP45xS Probe Assembly Instructions - Direct MountTMS2000 Installation.doc 07-11-05PAGE 15
INSTRUCTION MANUALTMS20004. Tighten the cable connector on top of the probe housing to ensure a WATERTIGHT SEAL.5. Route the probe cable to the junction box and complete the wiring installation in accordancewith Section 3EXTERNAL LEAK SENSOR INSTALLATIONThe interstitial or double-wall space of steel tanks and vaulted tanks as well as many othersecondary containment areas can be fitted with either DISCRIMINATING orNON-DISCRIMINATING leak sensors. Also, for float type non-discriminating sensors, switchactuation may be factory set for either NORMALLY OPEN or NORMALLY CLOSED.2.5 LEAK SENSOR INSTALLATION IN STEEL AND VAULTED TANKSCheck the specific design drawings for the job, or choose the sensor type desired from Figures 1-5and 1-6. Install sensor per Figure 2-7 as follows:1. Remove the watertight CORD CONNECTOR supplied by sliding it off the sensor cable.2. Thread the watertight CONNECTOR into the top of a 2" by 1/2" reducer bushing or monitor pipecap pre-tapped for a 1/2" NPT hole. (The use of any standard monitor cap from 2" to 4" pipesize is recommended. The cap or reducer bushing IS NOT SUPPLIED with the sensor and mustbe provided by the installer).3. Measure the "MOUNTING HEIGHT" from top to bottom of monitoring pipe.4. Feed the sensor cable through the watertight CONNECTOR from the BOTTOM SIDE of theREDUCER (or CAP) fitting to a cable length suitable for the MOUNTING HEIGHT; or to allowsensor to rest on the monitor pipe bottom; or as required by local codes. Cable may be cut orextended to proper length.5. Re-tighten the CORD CONNECTOR to fix the sensor cable length.6. Mate the REDUCER or CAP to the top of the monitor pipe. Tighten the CONNECTOR to ensurea WATERTIGHT SEAL.7. Route the sensor cable to the junction box and complete the wiring installation in accordancewith Section 3.MONITOR PIPECAP ORREDUCERWATERTIGHT JUNCTION BOXAND CONDUIT SEAL (SEE SECTION 3.3)12" MINIMUM MANHOLEIS REQUIRED FORUNDERGROUND TANKS2" OR LARGERMONITORING PIPEMOUNTING HEIGHTTANK LEAK SENSORMODELS LS600LDBN ORES825DOUBLE WALL TANKFigure 2-7 - Leak Sensor Installation - Steel Vaulted TanksDRAWING NO. 20016 REV. ATMS2000 Installation.doc 07-11-05PAGE 16
Page 1 and 2: Telephone 800-500-9311Telephone 864
Page 3 and 4: INSTRUCTION MANUALTMS2000Note: A se
Page 5 and 6: Liquid Level Control SystemsPAPERFE
Page 7 and 8: INSTRUCTION MANUALTMS2000The consol
Page 9 and 10: INSTRUCTION MANUALTMS20001.4 LIQUID
Page 11 and 12: INSTRUCTION MANUALTMS2000SECTION 2
Page 13 and 14: INSTRUCTION MANUALTMS20002.3 LEVEL
Page 15 and 16: INSTRUCTION MANUALTMS2000Install th
Page 17: INSTRUCTION MANUALTMS20002.4.2 BUSH
Page 21 and 22: INSTRUCTION MANUALTMS20002.7 LEAK S
Page 23 and 24: INSTRUCTION MANUALTMS20004. Feed th
Page 25 and 26: INSTRUCTION MANUALTMS2000BLK WHTRED
Page 27 and 28: INSTRUCTION MANUALTMS2000CABLE SELE
Page 29 and 30: INSTRUCTION MANUALTMS20003.2 POWER
Page 31 and 32: INSTRUCTION MANUALTMS2000WIRE SPLIC
Page 33 and 34: INSTRUCTION MANUALTMS2000WIRE SPLIC
Page 35 and 36: INSTRUCTION MANUALTMS20003.4 PROGRA
Page 37 and 38: INSTRUCTION MANUALTMS20003.6 PROBE

TMS2000 - OEC Fluid Handling, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?