TMS2000 - OEC Fluid Handling, Inc.

More documents

Recommendations

Info

INSTRUCTION MANUALTMS2000ASSEMBLY INSTRUCTIONS - RISER-MOUNTED MODEL MP45xSIMPORTANT! ALL of the following requirements must be met;• Probe length does not exceed 15 feet.• Tank does not contain chemicals, solvents or heated products where standard PVC leader cable is used.• Tank does contain chemical, solvent or heated products where chemical/heat resistant probe assembly and leader cable are used andconfirmed to be compatible with stored product.• Tank is not pressurized.Questions? Contact Technical Support at (800) 209-7858FOR INSTALLATION AND WIRING SEE TMS MANUAL1 Trim spacers for the desired schedule 40 riser pipe diameter. 34" RISER PIPEAssemble riser spacers.PROBE HEAD3" RISER PIPE2" RISER PIPE22Verify that the bottom of the locking collar is located 8" from thetop of the probe head and confirm that collar is secured.NOTE:HOLE #1(LARGER)1NOTE:HOLE #2(SMALLER)PROBE HEAD2STANDARD ALUMINUMLOCKING COLLAR(S.S. COLLAR INSTALLEDFOR CHEMICAL APPLICATIONS)8"1LOCKINGCOLLARNOTE: AT THIS POINT MODEL MP452S ASSEMBLY ISCOMPLETE. PROCEED TO STEP 4 TO COMPLETE MODELMP450S ASSEMBLY.44" RISER MOUNTING ASSEMBLY2" RISER MOUNTING ASSEMBLYSTANDARD APPLICATIONSSTANDARD APPLICATIONSCHEMICAL APPLICATIONSWITH INTERFACE WITHOUT INTERFACE WITH WITHOUTINTERFACE INTERFACEPRODUCTFLOATPRODUCTFLOATOPTIONALINTERFACEFLOATINTERFACEFLOATMETAL WEIGHTMETAL WEIGHTCATHODICBOOTCATHODICBOOTSPACERRETAININGRINGEND CAPRETAININGRINGEND CAPS.S. COLLARFLUSH WITH BOTTOMOF PROBE SHAFT1/2"S.S. COLLARPNEUMERCATORLiquid Level Control SystemsBulletin 164 Rev. D (12/03/04) Page 1 of 1Figure 2-3 - MP45xS Probe Assembly Instructions - Riser MountTMS2000 Installation.doc 07-11-05PAGE 11
INSTRUCTION MANUALTMS2000Install the level probe in the UNDERGROUND TANK as follows:1. Select the correct probes for the tank. Match the model number with tank internal dimensionsper Figure 1-4.2. Assemble the probe per Bulletin 164 shown in Figure 2-3.3. Slowly lower probe into tank opening until probe's FOOT REST is on the tank bottom. Theprobe should be vertical with both centering spacers totally supported within the riser pipe.4. Feed the probe cable through the underside of the riser cap cord grip supplied. Keep the griploose so cable can be flexed. Leave enough slack beneath the cap so the probe rests on thetank bottom, and above the cap to reach the electrical junction box in the manhole.5. Prepare riser pipe and cap with pipe dope or suitable compound, and carefully mate themtogether.6. Tighten the cable cord grip on top of the riser cap to ensure a WATERTIGHT SEAL.7. Route the probe cable to the manhole junction box and complete the electrical installation inaccordance with Section 3.2.4 LEVEL PROBE INSTALLATION IN ABOVEGROUND TANKSNOTE: For tanks located inside buildings or vaults, or under outdoor containment shelters:Rigid Level Probes models MP450S, MP451S, & MP452S require tank headroom clearance atleast equal to overall probe length for insertion and removal. See Figure 1-4 for probe dimensions.There are two methods of installing the level probe in aboveground tanks shown in Figures 2-4 and2-5. The choice is dictated by the actual fitting supplied integral to the probe.The standard method shown in Figure 2-4 uses a RISER PIPE mounted on top of the tank tosupport the probe; similar to an underground tank installation. The optional method shown in Figure2-5 employs a REDUCER FITTING to support the probe.Risers and reducers are SUPPLIED BY THE INSTALLER.TMS2000 Installation.doc 07-11-05PAGE 12
Page 1 and 2: Telephone 800-500-9311Telephone 864
Page 3 and 4: INSTRUCTION MANUALTMS2000Note: A se
Page 5 and 6: Liquid Level Control SystemsPAPERFE
Page 7 and 8: INSTRUCTION MANUALTMS2000The consol
Page 9 and 10: INSTRUCTION MANUALTMS20001.4 LIQUID
Page 11 and 12: INSTRUCTION MANUALTMS2000SECTION 2
Page 13: INSTRUCTION MANUALTMS20002.3 LEVEL
Page 17 and 18: INSTRUCTION MANUALTMS20002.4.2 BUSH
Page 19 and 20: INSTRUCTION MANUALTMS20004. Tighten
Page 21 and 22: INSTRUCTION MANUALTMS20002.7 LEAK S
Page 23 and 24: INSTRUCTION MANUALTMS20004. Feed th
Page 25 and 26: INSTRUCTION MANUALTMS2000BLK WHTRED
Page 27 and 28: INSTRUCTION MANUALTMS2000CABLE SELE
Page 29 and 30: INSTRUCTION MANUALTMS20003.2 POWER
Page 31 and 32: INSTRUCTION MANUALTMS2000WIRE SPLIC
Page 33 and 34: INSTRUCTION MANUALTMS2000WIRE SPLIC
Page 35 and 36: INSTRUCTION MANUALTMS20003.4 PROGRA
Page 37 and 38: INSTRUCTION MANUALTMS20003.6 PROBE

TMS2000 - OEC Fluid Handling, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?