TMS2000 - OEC Fluid Handling, Inc.

More documents

Recommendations

Info

INSTRUCTION MANUALTMS2000Ø.130"PULL HOLE3.02"25' LONGCABLE1.50"CABLE GRIP.236 REF.1/2" LIQUIDTRIP POINT.40"DRAWING NO. 20008 REV. N/CFigure 1-7 – LS61016' LONG22 AWG CABLE16' LONG22 AWG CABLECABLE GRIPCABLE GRIPPVC HOUSINGFLOATHIGHALARM18.25"15.00"11.00"15.00"18.25"FLOATLOWALARM2.25" 2.25"Ø2.88"Ø2.88"DRAWING NO. 20009 REV. N/CFigure 1-8 – RSU800TMS2000 Installation.doc 07-11-05PAGE 7
INSTRUCTION MANUALTMS2000SECTION 2 – INSTALLATION DETAILS2.1 INSTALLATION CHECKLISTWARNINGDo NOT apply power to the TMS2000 until its installation has been checked andfound to be in accordance with these instructions; National Electric Code;Federal, State and Local codes; and other applicable safety codes. FAILURE TOCOMPLY MAY RESULT IN PERSONAL INJURY, PROPERTY LOSS ANDEQUIPMENT DAMAGE.The following points should be reviewed in preparation for installation, and again when installationis complete.1. Review Figure 3-1 to ensure that all of the safety/wiring requirements have been met.2. Check that all equipment at job site matches the DESIGN DRAWING SPECIFICATIONS for thetank sizes and control features required.3. The console should be located as close as possible to the demarcation point of the hazardousarea. Never mount inside the hazardous area.4. POWER to the console should be properly wired to a DEDICATED 120/240 VAC CIRCUITBREAKER. No other equipment can be powered from the same circuit breaker as the TMS.5. System cannot be connected to equipment that uses or generates more than 250 volts withrespect to earth.6. All TMS grounds must be terminated at the GND BUSS BAR in the same service panel as TMSpower. A grounding rod, coldwater pipe or other connection should not be used. Refer to Figure3-3 for illustrated details.7. The magnetostrictive probe inputs and the sensor inputs are two different intrinsically safecircuits and must be installed in separate cables or in one cable which has suitable insulation.Refer to NEC Article 504-30 (b) or CEC Appendix F6.3 for additional information.8. Do not drill or modify enclosure. Use only knockouts provided. Failure to comply will voidwarranty and may present a safety hazard.9. I.S. cabling should be selected from the Cable Selection Chart in Figure 3-2. Each probe orsensor wire/cable run SHOULD NOT EXCEED THE MAXIMUM DISTANCE RATING ON THECABLE SELECTION CHART. Color-coding or numbering is highly recommended.10. WATERPROOFING FIELD WIRE SPLICES using factory supplied splice kits is required forproper system operation.TMS2000 Installation.doc 07-11-05PAGE 8
Page 1 and 2: Telephone 800-500-9311Telephone 864
Page 3 and 4: INSTRUCTION MANUALTMS2000Note: A se
Page 5 and 6: Liquid Level Control SystemsPAPERFE
Page 7 and 8: INSTRUCTION MANUALTMS2000The consol
Page 9: INSTRUCTION MANUALTMS20001.4 LIQUID
Page 13 and 14: INSTRUCTION MANUALTMS20002.3 LEVEL
Page 15 and 16: INSTRUCTION MANUALTMS2000Install th
Page 17 and 18: INSTRUCTION MANUALTMS20002.4.2 BUSH
Page 19 and 20: INSTRUCTION MANUALTMS20004. Tighten
Page 21 and 22: INSTRUCTION MANUALTMS20002.7 LEAK S
Page 23 and 24: INSTRUCTION MANUALTMS20004. Feed th
Page 25 and 26: INSTRUCTION MANUALTMS2000BLK WHTRED
Page 27 and 28: INSTRUCTION MANUALTMS2000CABLE SELE
Page 29 and 30: INSTRUCTION MANUALTMS20003.2 POWER
Page 31 and 32: INSTRUCTION MANUALTMS2000WIRE SPLIC
Page 33 and 34: INSTRUCTION MANUALTMS2000WIRE SPLIC
Page 35 and 36: INSTRUCTION MANUALTMS20003.4 PROGRA
Page 37 and 38: INSTRUCTION MANUALTMS20003.6 PROBE

TMS2000 - OEC Fluid Handling, Inc.

Create successful ePaper yourself

Delete template?

Save as template?