CMS/User Guide - Filterteknik

More documents

Recommendations

Info

Appendix DSize μm(c) >4 >6 >14 >21 >38 >70Size Code A B C D E FClasses000 195 76 14 3 1 000 390 152 27 5 1 00 780 304 54 10 2 01 1,560 609 109 20 4 12 3,120 1,217 217 39 7 13 6,250 2,432 432 76 13 24 12,500 4,864 864 152 26 45 25,000 9,731 1,731 306 53 86 50,000 19,462 3,462 612 106 167 100,000 38,924 6,924 1,224 212 328 200,000 77,849 13,849 2,449 424 649 400,000 155,698 27,698 4,898 848 12810 800,000 311,396 55,396 9,796 1,696 25611 1,600,000 622,792 110,792 19,592 3,392 51212 3,200,000 1,245,584 221,584 39,184 6,784 1,024Table D.IICountsAS4059E Table 2 - Cleanliness Classes for Cumulative Particle68 SAE AS4059 REV.E Cleanliness Classification For . . .
Appendix ERecommendationsUnit Type ISO 4406:1999 CodePUMP Piston (slow speed, in-line) 22/20/16Piston (high speed, variable) 17/15/13Gear 19/17/15Vane 18/16/14MOTOR Axial piston 18/16/13Radial piston 19/17/13Gear 20/18/15Vane 19/17/14VALVE Directional (solenoid) 20/18/15Pressure control (modulating) 19/17/14Flow control 19/17/14Check valve 20/18/15Cartridge valve 20/18/15Proportional 18/16/13Servo-valve 16/14/11ACTUATOR 20/18/15Table E.I Typical Manufacturers Recommendations for ComponentCleanliness (ISO 4406:1999) XXMost component manufacturers know the proportionate effect that increaseddirt level has on the performance of their components and issue maximumpermissible contamination levels. They state that operating components onXX It should be noted that the recommendations made in this table should be viewed as startinglevels and may have to be modified in light of operational experiences or user requirements.Recommendations 69
Page 1 and 2:
CMSContamination Monitoring System
Page 3 and 4:
Contents1 Introduction 7•Operatin
Page 5:
E Recommendations 69F Hydraulic Sys
Page 8 and 9:
2 How to OrderExample: CMS - W M K
Page 10 and 11:
It comprises a USB:RS485 interface
Page 12 and 13:
Moisture &TemperatureMeasurementDat
Page 14 and 15:
4 Status LEDAll CMS versions have a
Page 16 and 17:
5 Front Panel Operation5.1 Result D
Page 18 and 19: SimpleDetailedFigure 5.4 AS4059E Ta
Page 20 and 21: 6 Water SensorCMS-W models measure
Page 22 and 23: 7 Data LoggerThe CMS includes a bui
Page 24 and 25: 9 USBi Optional Computer USBInterfa
Page 26 and 27: is separately available as a pre-wi
Page 28 and 29: 11 PC Software OperationThe Remote
Page 30 and 31: 12 SettingsThe CMS can be reconfigu
Page 32 and 33: The factory set value of 2 minutes
Page 34 and 35: large particles in the system. When
Page 36 and 37: NAS1638 can be used by selecting th
Page 38 and 39: This allows the CMS to switch exter
Page 40 and 41: Turns on When Test Complete ≤Lowe
Page 42 and 43: • If there is no suitable differe
Page 44 and 45: 14.1 DC PowerDC power is connected
Page 46 and 47: supplies can be used to power each
Page 48 and 49: Other ways to start a test are:•
Page 50 and 51: 15.1 Flow Rate15.1.1 SummaryFor the
Page 52 and 53: • See the figures at the start of
Page 54 and 55: 15.3 Active Flow ControlThis is onl
Page 56 and 57: allows a system to remotely monitor
Page 58 and 59: 17 Cycle Time and Flow RateConsider
Page 60 and 61: 18 Modbus ProgrammingThe CMS can be
Page 62 and 63: Appendix ATypical Water Saturation
Page 64 and 65: Appendix BMicroscope counting exami
Page 66 and 67: Appendix DSAE AS4059 REV.E Cleanlin
Page 70 and 71: Appendix Efluids which are cleaner
Page 72 and 73: Appendix FContamination Correspondi
Page 74 and 75: Appendix GISO therefore defined the
Page 76 and 77: Appendix GTo clarify matters still
Page 78 and 79: Appendix Gbut often no direct compa
Page 80: Appendix G80 New ISO Medium Test Du
show all

CMS/User Guide - Filterteknik

Create successful ePaper yourself

Delete template?

Save as template?