CMS/User Guide - Filterteknik

More documents

Recommendations

Info

allows a system to remotely monitor the CMS operation, if desired,allowing more specific diagnostics. 14Value Function Comment0 NOT READY Unit is powering-up, or there issome problem1 READY Ready to start a test 152 TESTING Test in progress3 WAITING Waiting between tests 16128 FAULT OPTICAL LED failure / sensor blocked /filled with air129 FAULT FLOWLOWFlow too low for reliable test 17130 FAULT FLOWHIGH131 FAULT LOGGING Fault with data logging132 FAULT WATERSENSORWater sensor failureTable 16.1The TEST STATUS Register14 However the fault conditions are also indicated on the front panel LED, while ``NoResult’’ in the case of a fault is indicated using special result values as previouslydescribed.15 User has not set tests to occur automatically.16 User has set a non-zero test interval.17 Or fluid is totally clean (no particle counts). Flow alarm can be turned off by userif this is a problem, for example cleaning rigs.56 Fault Finding
16.3 Other FaultsUnexpected resultsobtained fromsampleRemote Devicedialogue notresponding tobuttons beingpressed.Check that the Mini-mess hose has been fullyconnected at both the system and CMS ends.Confirm that the flow through the CMS iswithin the range of the unit.High water / aeration levels.Check that correct COM port has been selectedin the Remote Device dialogue.Disconnect power supply to CMS and thenreconnect it.If the CMS has been subjected to excessive contamination and ablockage is suspected, a flush with a suitable solvent may clear theblockage.The standard CMS is fitted with Viton seals, so Petroleum Ethermay be used for this purpose, in conjunction with the RMF SystemsBottle Sampling Unit.DO NOT USE ACETONEFault Finding 57
Page 1 and 2:
CMSContamination Monitoring System
Page 3 and 4:
Contents1 Introduction 7•Operatin
Page 5: E Recommendations 69F Hydraulic Sys
Page 8 and 9: 2 How to OrderExample: CMS - W M K
Page 10 and 11: It comprises a USB:RS485 interface
Page 12 and 13: Moisture &TemperatureMeasurementDat
Page 14 and 15: 4 Status LEDAll CMS versions have a
Page 16 and 17: 5 Front Panel Operation5.1 Result D
Page 18 and 19: SimpleDetailedFigure 5.4 AS4059E Ta
Page 20 and 21: 6 Water SensorCMS-W models measure
Page 22 and 23: 7 Data LoggerThe CMS includes a bui
Page 24 and 25: 9 USBi Optional Computer USBInterfa
Page 26 and 27: is separately available as a pre-wi
Page 28 and 29: 11 PC Software OperationThe Remote
Page 30 and 31: 12 SettingsThe CMS can be reconfigu
Page 32 and 33: The factory set value of 2 minutes
Page 34 and 35: large particles in the system. When
Page 36 and 37: NAS1638 can be used by selecting th
Page 38 and 39: This allows the CMS to switch exter
Page 40 and 41: Turns on When Test Complete ≤Lowe
Page 42 and 43: • If there is no suitable differe
Page 44 and 45: 14.1 DC PowerDC power is connected
Page 46 and 47: supplies can be used to power each
Page 48 and 49: Other ways to start a test are:•
Page 50 and 51: 15.1 Flow Rate15.1.1 SummaryFor the
Page 52 and 53: • See the figures at the start of
Page 54 and 55: 15.3 Active Flow ControlThis is onl
Page 58 and 59: 17 Cycle Time and Flow RateConsider
Page 60 and 61: 18 Modbus ProgrammingThe CMS can be
Page 62 and 63: Appendix ATypical Water Saturation
Page 64 and 65: Appendix BMicroscope counting exami
Page 66 and 67: Appendix DSAE AS4059 REV.E Cleanlin
Page 68 and 69: Appendix DSize μm(c) >4 >6 >14 >21
Page 70 and 71: Appendix Efluids which are cleaner
Page 72 and 73: Appendix FContamination Correspondi
Page 74 and 75: Appendix GISO therefore defined the
Page 76 and 77: Appendix GTo clarify matters still
Page 78 and 79: Appendix Gbut often no direct compa
Page 80: Appendix G80 New ISO Medium Test Du
show all

CMS/User Guide - Filterteknik

Create successful ePaper yourself

Delete template?

Save as template?