CMS/User Guide - Filterteknik

More documents

Recommendations

Info

supplies can be used to power each CMS, or a single supply runthrough the trunk cable.Figure 14.4Remote Display Unit Including PC Controller ExampleFigure 14.4 shows how to connect the CMS-RDU Remote DisplayUnit. The RDU is used when the CMS location is not convenientfor an operator. It can control and monitor a remote CMS, as well asallowing an external controller to be connected to it (for data download,for example).14.3 Switched Input and Output SignalsThe CMS has one switched input and two switched outputs. Thesecan be used instead of, or in addition to, the RS485 interface forcommand and control. The RS485 interface is more flexible butrequires more software work if CMS-View is not used (e.g. controlfrom a PLC). An alternative is to control the CMS via these switchedsignals, either from a PLC or using a manual switch and indicators.46 Electrical Interface
Figure 14.5Switched I/O SignalsIn order to reduce wiring the input and outputs all connect togetheron one side (see Figure 14.5). However they are optically isolatedfrom the rest of the system so can be used to switch unrelated signals.14.4 Start SignalThe "start signal’’ is an opto-isolated input that can be used to starta test. This could be from a push button or a PLC output. The inputaccepts AC or DC signals, typically derived from the DC supplyvoltage. The exact function of this input is determined by the TestMode setting (12.6).Item Minimum MaximumVoltage 9V DC 36V DCImpedance10k OhmsElectrical Interface 47
Page 1 and 2: CMSContamination Monitoring System
Page 3 and 4: Contents1 Introduction 7•Operatin
Page 5: E Recommendations 69F Hydraulic Sys
Page 8 and 9: 2 How to OrderExample: CMS - W M K
Page 10 and 11: It comprises a USB:RS485 interface
Page 12 and 13: Moisture &TemperatureMeasurementDat
Page 14 and 15: 4 Status LEDAll CMS versions have a
Page 16 and 17: 5 Front Panel Operation5.1 Result D
Page 18 and 19: SimpleDetailedFigure 5.4 AS4059E Ta
Page 20 and 21: 6 Water SensorCMS-W models measure
Page 22 and 23: 7 Data LoggerThe CMS includes a bui
Page 24 and 25: 9 USBi Optional Computer USBInterfa
Page 26 and 27: is separately available as a pre-wi
Page 28 and 29: 11 PC Software OperationThe Remote
Page 30 and 31: 12 SettingsThe CMS can be reconfigu
Page 32 and 33: The factory set value of 2 minutes
Page 34 and 35: large particles in the system. When
Page 36 and 37: NAS1638 can be used by selecting th
Page 38 and 39: This allows the CMS to switch exter
Page 40 and 41: Turns on When Test Complete ≤Lowe
Page 42 and 43: • If there is no suitable differe
Page 44 and 45: 14.1 DC PowerDC power is connected
Page 48 and 49: Other ways to start a test are:•
Page 50 and 51: 15.1 Flow Rate15.1.1 SummaryFor the
Page 52 and 53: • See the figures at the start of
Page 54 and 55: 15.3 Active Flow ControlThis is onl
Page 56 and 57: allows a system to remotely monitor
Page 58 and 59: 17 Cycle Time and Flow RateConsider
Page 60 and 61: 18 Modbus ProgrammingThe CMS can be
Page 62 and 63: Appendix ATypical Water Saturation
Page 64 and 65: Appendix BMicroscope counting exami
Page 66 and 67: Appendix DSAE AS4059 REV.E Cleanlin
Page 68 and 69: Appendix DSize μm(c) >4 >6 >14 >21
Page 70 and 71: Appendix Efluids which are cleaner
Page 72 and 73: Appendix FContamination Correspondi
Page 74 and 75: Appendix GISO therefore defined the
Page 76 and 77: Appendix GTo clarify matters still
Page 78 and 79: Appendix Gbut often no direct compa
Page 80: Appendix G80 New ISO Medium Test Du

CMS/User Guide - Filterteknik

Create successful ePaper yourself

Delete template?

Save as template?