CMS/User Guide - Filterteknik

More documents

Recommendations

Info

Turns on When Test Complete ≤LowerIntended Function Test Complete Signal "Pass’’ SignalThis is used when controlling tests from a PLC using switched outputs.The PLC gives a start signal, then monitors the "Test Complete’’output. If the test has passed it can detect this with the "Pass’’signal.Alarm Mode 6... Customer Requested ModesOther alarm modes will be defined as and when customers requestthem.40 Settings
13 InstallationEach CMS supplied consists of the following:• CMS• Calibration certificate• CMS-View CD ROM, software package• Pre-wired cableOptional Equipment:• Circular connector pre-wired with 3m cable• CMS-RDU Remote display unit• 500 µm coarse screen filter• CMS-FC1 Flow Control Valve• CMS-USBi USB adaptor with pre-wired CMS cable13.1 Installation Procedure• Decide on tapping points in hydraulic circuit.• Locate the unit mechanically and bolt to desired location usingfixing holes provided. The CMS must be in a vertical orientation,with the oil flowing upwards through it.• Wire back to junction box.• Check flow in acceptable range. There needs to be a differentialpressure placed across the CMS, such that a flow of fluid isgenerated within the range of the unit.Installation 41
Page 1 and 2: CMSContamination Monitoring System
Page 3 and 4: Contents1 Introduction 7•Operatin
Page 5: E Recommendations 69F Hydraulic Sys
Page 8 and 9: 2 How to OrderExample: CMS - W M K
Page 10 and 11: It comprises a USB:RS485 interface
Page 12 and 13: Moisture &TemperatureMeasurementDat
Page 14 and 15: 4 Status LEDAll CMS versions have a
Page 16 and 17: 5 Front Panel Operation5.1 Result D
Page 18 and 19: SimpleDetailedFigure 5.4 AS4059E Ta
Page 20 and 21: 6 Water SensorCMS-W models measure
Page 22 and 23: 7 Data LoggerThe CMS includes a bui
Page 24 and 25: 9 USBi Optional Computer USBInterfa
Page 26 and 27: is separately available as a pre-wi
Page 28 and 29: 11 PC Software OperationThe Remote
Page 30 and 31: 12 SettingsThe CMS can be reconfigu
Page 32 and 33: The factory set value of 2 minutes
Page 34 and 35: large particles in the system. When
Page 36 and 37: NAS1638 can be used by selecting th
Page 38 and 39: This allows the CMS to switch exter
Page 42 and 43: • If there is no suitable differe
Page 44 and 45: 14.1 DC PowerDC power is connected
Page 46 and 47: supplies can be used to power each
Page 48 and 49: Other ways to start a test are:•
Page 50 and 51: 15.1 Flow Rate15.1.1 SummaryFor the
Page 52 and 53: • See the figures at the start of
Page 54 and 55: 15.3 Active Flow ControlThis is onl
Page 56 and 57: allows a system to remotely monitor
Page 58 and 59: 17 Cycle Time and Flow RateConsider
Page 60 and 61: 18 Modbus ProgrammingThe CMS can be
Page 62 and 63: Appendix ATypical Water Saturation
Page 64 and 65: Appendix BMicroscope counting exami
Page 66 and 67: Appendix DSAE AS4059 REV.E Cleanlin
Page 68 and 69: Appendix DSize μm(c) >4 >6 >14 >21
Page 70 and 71: Appendix Efluids which are cleaner
Page 72 and 73: Appendix FContamination Correspondi
Page 74 and 75: Appendix GISO therefore defined the
Page 76 and 77: Appendix GTo clarify matters still
Page 78 and 79: Appendix Gbut often no direct compa
Page 80: Appendix G80 New ISO Medium Test Du

CMS/User Guide - Filterteknik

Create successful ePaper yourself

Delete template?

Save as template?