CMS/User Guide - Filterteknik

More documents

Recommendations

Info

4 Status LEDAll CMS versions have a multicolour indicator 3 on the front panel,which is used to indicate the status or alarm state. The alarm thresholdscan be set from CMS-View via the serial interface.CMS-KCMSFigure 4.1Front Panel VersionsGreen indicates that the test result passed, i.e. none of the alarmthresholds were exceeded.Yellow indicates that the lower cleanliness limit was exceeded, butnot the upper one.Red indicates that the upper cleanliness limit was exceeded.Blue indicates that the upper water content limit was exceeded.Red/Blue Alternating indicates both cleanliness and water contentupper limits exceeded.3 If all these codes seem confusing, please note that a given colour will only everbe seen if the corresponding limit has been specifically set by the user. So forexample if a maximum temperature limit has not been set, the violet indicationwill never be seen. If all that is wanted is a "green or red’’ light, that can bearranged by simply setting only the cleanliness threshold maximum limit.14 Status LED
Violet indicates that the upper temperature limit was exceeded. 4The LED can also indicate various fault codes by turning red andflashing white a number of times, see section 16.1.4 This alarm, if set, takes priority over the Contamination and Water alarms. In theevent of an over-temperature condition, the LED will turn violet only, whether ornot there is also a contamination or water alarm condition. The rationale is thatan over-temperature condition could be immediately catastrophic for the hydraulicsystem.Status LED 15
Page 1 and 2: CMSContamination Monitoring System
Page 3 and 4: Contents1 Introduction 7•Operatin
Page 5: E Recommendations 69F Hydraulic Sys
Page 8 and 9: 2 How to OrderExample: CMS - W M K
Page 10 and 11: It comprises a USB:RS485 interface
Page 12 and 13: Moisture &TemperatureMeasurementDat
Page 16 and 17: 5 Front Panel Operation5.1 Result D
Page 18 and 19: SimpleDetailedFigure 5.4 AS4059E Ta
Page 20 and 21: 6 Water SensorCMS-W models measure
Page 22 and 23: 7 Data LoggerThe CMS includes a bui
Page 24 and 25: 9 USBi Optional Computer USBInterfa
Page 26 and 27: is separately available as a pre-wi
Page 28 and 29: 11 PC Software OperationThe Remote
Page 30 and 31: 12 SettingsThe CMS can be reconfigu
Page 32 and 33: The factory set value of 2 minutes
Page 34 and 35: large particles in the system. When
Page 36 and 37: NAS1638 can be used by selecting th
Page 38 and 39: This allows the CMS to switch exter
Page 40 and 41: Turns on When Test Complete ≤Lowe
Page 42 and 43: • If there is no suitable differe
Page 44 and 45: 14.1 DC PowerDC power is connected
Page 46 and 47: supplies can be used to power each
Page 48 and 49: Other ways to start a test are:•
Page 50 and 51: 15.1 Flow Rate15.1.1 SummaryFor the
Page 52 and 53: • See the figures at the start of
Page 54 and 55: 15.3 Active Flow ControlThis is onl
Page 56 and 57: allows a system to remotely monitor
Page 58 and 59: 17 Cycle Time and Flow RateConsider
Page 60 and 61: 18 Modbus ProgrammingThe CMS can be
Page 62 and 63: Appendix ATypical Water Saturation
Page 64 and 65:
Appendix BMicroscope counting exami
Page 66 and 67:
Appendix DSAE AS4059 REV.E Cleanlin
Page 68 and 69:
Appendix DSize μm(c) >4 >6 >14 >21
Page 70 and 71:
Appendix Efluids which are cleaner
Page 72 and 73:
Appendix FContamination Correspondi
Page 74 and 75:
Appendix GISO therefore defined the
Page 76 and 77:
Appendix GTo clarify matters still
Page 78 and 79:
Appendix Gbut often no direct compa
Page 80:
Appendix G80 New ISO Medium Test Du
show all

CMS/User Guide - Filterteknik

Create successful ePaper yourself

Delete template?

Save as template?