CMS/User Guide - Filterteknik

More documents

Recommendations

Info

Moisture &TemperatureMeasurementData StorageKeypad & LCD% saturation (RH) and fluid temperature(°C) – MineralOil Only. See section 6Approximately 4000 timestamped tests in the integralCMS memory.6 keys, 128x64 pixels, back-lit graphical display3.2 HydraulicFluid CompatibilityFlow RateViscosity RangeStandard unit: Mineral oil & petroleum based fluids.Consult RMF Systems for other fluids.20-400 ml/minute
VibrationTBD3.4 PhysicalDimensionsFixing HolesWeight117mm(H)x142mm(W)x65mm(D).Centers 126mm apart, Diameter 6.9mm (for M6).1.15kg3.5 ElectricalSupply Voltage9-36V DCSupply Current12V 24V 36V150mA 80mA 60mAfor K version70mA 40mA 30mAfor non K versionPower Consumption 2.2WSwitched Inputs &Outputssee section 14.3 for details3.6 Warranty and RecalibrationWarrantyThe CMS is guaranteed for 12 months from date ofreceipt.Re-calibration The CMS is recommended to be recalibrated every 12months. Return to RMF Systems for recalibration.As a policy of continual improvement, RMF Systems reserve the right to alter thespecification without prior notice.Specification 13
Page 1 and 2: CMSContamination Monitoring System
Page 3 and 4: Contents1 Introduction 7•Operatin
Page 5: E Recommendations 69F Hydraulic Sys
Page 8 and 9: 2 How to OrderExample: CMS - W M K
Page 10 and 11: It comprises a USB:RS485 interface
Page 14 and 15: 4 Status LEDAll CMS versions have a
Page 16 and 17: 5 Front Panel Operation5.1 Result D
Page 18 and 19: SimpleDetailedFigure 5.4 AS4059E Ta
Page 20 and 21: 6 Water SensorCMS-W models measure
Page 22 and 23: 7 Data LoggerThe CMS includes a bui
Page 24 and 25: 9 USBi Optional Computer USBInterfa
Page 26 and 27: is separately available as a pre-wi
Page 28 and 29: 11 PC Software OperationThe Remote
Page 30 and 31: 12 SettingsThe CMS can be reconfigu
Page 32 and 33: The factory set value of 2 minutes
Page 34 and 35: large particles in the system. When
Page 36 and 37: NAS1638 can be used by selecting th
Page 38 and 39: This allows the CMS to switch exter
Page 40 and 41: Turns on When Test Complete ≤Lowe
Page 42 and 43: • If there is no suitable differe
Page 44 and 45: 14.1 DC PowerDC power is connected
Page 46 and 47: supplies can be used to power each
Page 48 and 49: Other ways to start a test are:•
Page 50 and 51: 15.1 Flow Rate15.1.1 SummaryFor the
Page 52 and 53: • See the figures at the start of
Page 54 and 55: 15.3 Active Flow ControlThis is onl
Page 56 and 57: allows a system to remotely monitor
Page 58 and 59: 17 Cycle Time and Flow RateConsider
Page 60 and 61: 18 Modbus ProgrammingThe CMS can be
Page 62 and 63:
Appendix ATypical Water Saturation
Page 64 and 65:
Appendix BMicroscope counting exami
Page 66 and 67:
Appendix DSAE AS4059 REV.E Cleanlin
Page 68 and 69:
Appendix DSize μm(c) >4 >6 >14 >21
Page 70 and 71:
Appendix Efluids which are cleaner
Page 72 and 73:
Appendix FContamination Correspondi
Page 74 and 75:
Appendix GISO therefore defined the
Page 76 and 77:
Appendix GTo clarify matters still
Page 78 and 79:
Appendix Gbut often no direct compa
Page 80:
Appendix G80 New ISO Medium Test Du
show all

CMS/User Guide - Filterteknik

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?