SITE BOOK - Plaster systems - British Gypsum
SITE BOOK - Plaster systems - British Gypsum SITE BOOK - Plaster systems - British Gypsum
Technical support: T 0844 800 1991 F 0844 561 8816 E bgtechnical.enquiries@bpb.comTable 4 – plaster selectionSkim finishplasterWhat is the background surface?suctionHigh LowDry undercoatsDamp undercoatsPlasterboardFlat, smoothconcreteWaterproofedcement-basedundercoatsThickness appliedCoverage per bag(at 2mm)Water requirement(litres per bag)Dry set weight(at 2mm thickness)Plaster systemsGypLyner UNIVERSALThistle DurafinishUSEUSESkim coatA versatile plaster that is 60%tougher than standard skimplasters.Thistle Spray FinishGypsum finish plaster for sprayor hand application.GGUSEBUSEB2mm2mm10m 21211m 2123.4kg/m 22.4kg/m 2ON MRBOARDSSetting times: Thistle finish plasters - 1 1/ 2 to 1 3/ 4 hours or longer in cold weather.Minimum temperature to be maintained until dry.Suctioncontrol+5°C for Thistle Durafinish, +2°C for Thistle Spray Finish.Thistle GypPrimeSuction control primer used to reduce suction on very dry backgrounds. Use diluted (up to five parts water to one partThistle GypPrime) or undiluted if severe suction control is required. Plaster is applied after Thistle GypPrime hassoaked into the background.G Use Thistle GypPrime where you see this symbol.BondingagentThistleBond-itBonding agent for smooth low-suction backgrounds.Apply undiluted, in one coat. Plaster when dry.B Use ThistleBond-it where you see this symbol.9415
www.british-gypsum.comPlaster systems9Installation – background preparationGeneralAll surfaces should be reasonably dry and protected from theweather. The suitability of a particular background forplastering should be considered in relation to its strength,suction, bonding properties, shrinkage or thermal movementcharacteristics, water and soluble salt content. Very high orlow suction substrates should be pre-treated. With theexception of skimming with Thistle Uni-Finish the use ofThistleBond-it is recommended for smooth backgrounds,whilst Thistle GypPrime is recommended for very highsuction backgrounds. The high suction of certainbackgrounds can be suitably adjusted by sprinkling withwater.Brickwork / blockworkThe surface must be clean, dry and suitable to receivegypsum plaster. Control suction with water if necessary. Ifsuction is severe the background should be pre-treated withThistle GypPrime.On high suction brick / blockwork the use of Thistle Hardwallor Thistle Tough Coat is recommended.Low suction backgrounds such as some concrete blocks andengineering bricks provide minimal absorption. The jointsshould be raked thoroughly to give an adequate mechanicalkey. Smooth backgrounds should be pre-treated withThistleBond-it.Dense aggregate concrete blocks do not require wettingprior to plastering, but the plaster should be applied withvery firm pressure to ensure intimate contact with thebackground.ConcreteThe surface must be clean, dry and suitable to receivegypsum plaster. Any mould, oils or other agents presentshould be removed from the surface.No-fines concrete does not require wetting prior toplastering.Normal ballast concrete should be given sufficient time tomature before applying plaster. The plaster should not beapplied onto a green background or when any free water isvisible. Mature concrete will require wetting to displace theair before plastering. Clean water should be applied 5 - 10minutes before plaster application.With the exception of skimming with Thistle Uni-Finish,in-situ or pre-cast concrete which is exceptionally smooth, or416
- Page 1 and 2: Plaster systemsPlaster systemsThist
- Page 3 and 4: Plaster systems9410ComponentsThistl
- Page 5 and 6: 4129Plaster systemsTwo coatAircrete
- Page 7: www.british-gypsum.comGypWall Plast
- Page 11 and 12: www.british-gypsum.comPlaster syste
- Page 13 and 14: www.british-gypsum.comPlaster syste
- Page 15 and 16: www.british-gypsum.comPlaster syste
- Page 17 and 18: www.british-gypsum.comPlaster syste
- Page 19 and 20: www.british-gypsum.comPlaster syste
Technical support: T 0844 800 1991 F 0844 561 8816 E bgtechnical.enquiries@bpb.comTable 4 – plaster selectionSkim finishplasterWhat is the background surface?suctionHigh LowDry undercoatsDamp undercoats<strong>Plaster</strong>boardFlat, smoothconcreteWaterproofedcement-basedundercoatsThickness appliedCoverage per bag(at 2mm)Water requirement(litres per bag)Dry set weight(at 2mm thickness)<strong>Plaster</strong> <strong>systems</strong>GypLyner UNIVERSALThistle DurafinishUSEUSESkim coatA versatile plaster that is 60%tougher than standard skimplasters.Thistle Spray Finish<strong>Gypsum</strong> finish plaster for sprayor hand application.GGUSEBUSEB2mm2mm10m 21211m 2123.4kg/m 22.4kg/m 2ON MRBOARDSSetting times: Thistle finish plasters - 1 1/ 2 to 1 3/ 4 hours or longer in cold weather.Minimum temperature to be maintained until dry.Suctioncontrol+5°C for Thistle Durafinish, +2°C for Thistle Spray Finish.Thistle GypPrimeSuction control primer used to reduce suction on very dry backgrounds. Use diluted (up to five parts water to one partThistle GypPrime) or undiluted if severe suction control is required. <strong>Plaster</strong> is applied after Thistle GypPrime hassoaked into the background.G Use Thistle GypPrime where you see this symbol.BondingagentThistleBond-itBonding agent for smooth low-suction backgrounds.Apply undiluted, in one coat. <strong>Plaster</strong> when dry.B Use ThistleBond-it where you see this symbol.9415