FUGA COLOR - DAST

FUGA COLORCement based grouts for joints with selected granulometryand high stability against water; it serves forfilling the joints from 0 to 5 mm.Technical CharacteristicsCement based material in the form of powder, with a naturalstone powder with a selected granulometry, syntheticresins, hydrophobic additives and coloring pigments.• Very good workability and spreading• It can be easily cleaned• It leaves a polished surface at the end.• Waterproof material• High resistance to bases (alkalis) and detergents• Resistant to erosion (corrosion)• Resistant to UV rays.• It prevents the efflorescent process.• Available in 24 colors.• According to the classification EN 13888, belongingto the category CG2.Area of useFugacolor 0-5 mm can be used in these cases as follows:Fuges caulking between porous ceramic tiles, monocotto,bicotto, gres porcelain and natural stone with a space of0-5mm.For the floor’s caulking and exterior coatings, when anincrease of the impenetrability , elasticity and mechanicalpower, for vibration surfaces, for surfaces with shrinkageand inflation (terraces, heating system floors, pools,fountains etc), stucco Fugacolor must be reinforced with500gr additive DW 17 diluted with 700-1000 ml water foran amount of 5 kg Fugacolor.moment when the Fugacolor has achieved stability, the requiredconsistency (a consistency which are achieved in 10-20 minutes after the application of the Fugacolor 0-5mm).The final cleaning of the tiles is done with a dry textile. Thefinal cleaning can be done even after a day when the materialis somehow solidified, and in this case an appropriatetextile is chosen for cleaning.TECHNICAL DATA AT 23 0 C AND 50% U.RFormPowderColor24 colors (see the table ofcolors)Preservation12 months in originalpacking at a dry placeCombustibilityIncombustibile1-1.5 L for 5 kg FugacolorWater demand7-7.5 L for 25 FugacolorConsistency of mixture Fluid and liquid mixtureDensity of mixture 2 gr/cm 3Mixture pH 12Pot life 2 hoursApplicaition temperature +5 0 C to +35 0 CImportant notesDo not use it for fuges bigger than those recommended.Application MethodBy using Fugacolor 0-5mm the space between tiles canbe easily filled by using a rubber trowel. The removal of theremaining mass must be done with a wet sponge at the

FUGA COLOR< 0.2 g/m 2 Absorbing (water absorbing) after4 h o u r s a c c o r d i n g t o ( E N 13 8 8 8 )coverageFinal dataStability to humidityGoodTiles size (cm)Fuges widthStability to solvents and fats Good2 mm 3 mm 4 mm 5 mmStability to acidsGood2 x 2 x 0,3 1.3 1.5Compression strength ≥ 25 N/mm 210 x 10 x 0,6 0.4 0.6 0.8 1Flexural strength ≥ 8 N/mm 215 x 15 x 0,7 0.3 0.45 0.62 0.77Passing rateafter 24 hours20 x 20 x 0,7 0.24 0.35 0.48 0.5820 x 30 x 0,7 0.2 0.3 0.4 0.48Pointing on wallsAfter 8 to 12 hours30 x 30 x 0,8 0.19 0.28 0.26 0.45Pointing on floorsAfter 24 to 36 hoursFuges cleaningafter 10 – 15 minutes PackingFugacolor 0-5 mm cardboard box 4*5 kgFugacolor 0-5 mm cardboard box 10*2 kgFinal data with the DW 17Resistance HumidityVery goodEwsistance to solvents and fats Very goodResistance to acidsVery goodCompression strength ≥ 32 N/mm 2Flexural strength ≥ 15 N/mm 2WARNING:The above indications and rules correspondto our best experience, but shall be deemed asmerely indicative and shall be confirmed by exhaustivepractical tests; thus, before using the product, the operatorshall determine if it is suitable for its intendeduse and shall undertake every responsibility resultingfrom its usePROFESSIONAL USE ONLY!