SQL Battery Monitor Data Manager User's Guide - Alber

More documents

Recommendations

Info

BDS DiagnosticsTo run the diagnostic that can confirm the direction of the current transducer (CT), click theCT Polarity tab on the dialog box. Select the DCM for the desired load module.Figure 142. Diagnostics - Load Module - CT Polarity (BDS)Under Select Load Module, select a load module, then click Load On. When the test finishes,the dialog box indicates Correct if the CT is oriented in the proper direction. If Incorrect isdisplayed, reverse the direction of the CT and perform the test again to confirm properorientation.29-4
BDS Diagnostics29.4. DIP Switch (BDS)String View > Diagnostics|DIP SwitchThe DIP Switch diagnostic confirms each position of the DIP switches inside the BDS andDCM. This diagnostic allows remote checking of switch settings. To open the diagnostic,select DIP Switch. The diagnostic indicates each switch position. Click the left or rightarrows to select other DCM units.Note The DIP switches are factory set and are not usually changed by the user.Figure 143. Diagnostics - DIP Switch (BDS)29-5
Page 6 and 7:
14. SETTING COMMUNICATIONS ........
Page 8 and 9:
31.4. Completing the Commissioning
Page 10 and 11:
Figure 45. System Setup - String (M
Page 12 and 13:
Figure 157. Equipment Owner (Comm A
Page 14:
System Requirements2. System Requir
Page 17 and 18:
Program Installation and Options4.4
Page 19 and 20:
Program Installation and Options6.
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Using Configure StationFigure 9. Co
Page 27 and 28:
Using Configure StationFigure 15. C
Page 29 and 30:
Setting Up the SQL Database6. Setti
Page 31 and 32:
Setting Up the SQL DatabaseFigure 2
Page 33 and 34:
Setting Up the SQL Database6.7. Ass
Page 35 and 36:
Setting Up the SQL Database6.8. Run
Page 37 and 38:
Setting Up the SQL Database6.11. Re
Page 39 and 40:
User Specific SettingsFigure 32. Us
Page 41 and 42:
User Specific Settings7.2. Battery
Page 43 and 44:
Practical Theory: Understanding Com
Page 45 and 46:
Practical Theory: Understanding Pol
Page 47 and 48:
Practical Theory: Understanding Pol
Page 49 and 50:
Practical Theory: Understanding Sys
Page 51 and 52:
Practical Theory: Understanding Sys
Page 53 and 54:
Practical Theory: Understanding How
Page 55 and 56:
Practical Theory: Understanding the
Page 57 and 58:
Selecting Preferences13. Selecting
Page 59 and 60:
Selecting PreferencesAlternate Fiel
Page 61 and 62:
Setting CommunicationsDisable Auto
Page 63 and 64:
Setting Up an Email Account15.1. Te
Page 65 and 66:
Setting Up a New MPM or BDS System1
Page 67 and 68:
Setting Up a New MPM or BDS SystemL
Page 69 and 70:
Setting Up a New MPM or BDS System1
Page 71 and 72:
Setting Up a New MPM or BDS SystemM
Page 73 and 74:
Setting Up a New MPM or BDS SystemA
Page 75 and 76:
Setting Up a New MPM or BDS SystemD
Page 77 and 78:
Setting Up a New MPM or BDS SystemA
Page 79 and 80:
Synchronizing Using Check SettingsN
Page 81 and 82:
Check Settings Screens18. Check Set
Page 83 and 84:
Check Settings ScreensThe Check Set
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Programming Battery Setup for the M
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Programming Battery Setup for the B
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Selecting the Database Range21. Sel
Page 125 and 126:
Viewing Battery and Monitor Status2
Page 127 and 128: Viewing Battery and Monitor StatusM
Page 129 and 130: Viewing Battery and Monitor StatusC
Page 131 and 132: Viewing Battery and Monitor Status2
Page 133 and 134: Viewing Battery and Monitor StatusS
Page 135 and 136: Viewing Battery and Monitor StatusT
Page 141 and 142: Viewing Battery and Monitor StatusS
Page 147 and 148: Using the Report Generator24. Using
Page 149 and 150: Using the Report Generator24.2. Det
Page 151 and 152: Using the Report Generator24.4. Tre
Page 157 and 158: Using the Report GeneratorSelect Ta
Page 159 and 160: Using the Report GeneratorThreshold
Page 161 and 162: Using the Preview Screens25.1. Savi
Page 163 and 164: Using the Web Report GeneratorMaint
Page 165 and 166: Calibration27. CalibrationString Vi
Page 167 and 168: MPM Diagnostics28. MPM DiagnosticsS
Page 169 and 170: MPM Diagnostics28.3. Load Module (M
Page 171 and 172: MPM Diagnostics28.5. Indicator (MPM
Page 173 and 174: MPM Diagnostics28.8. Contacts (MPM)
Page 175 and 176: BDS Diagnostics29. BDS DiagnosticsS
Page 177: BDS Diagnostics29.3. Load Module (B
Page 181 and 182: BDS Diagnostics29.7. Memory (BDS)St
Page 183 and 184: BDS DiagnosticsIntertier Voltage (m
Page 185 and 186: Upgrades30. UpgradesString View > S
Page 187 and 188: Commissioning Assistant31.2. Monito
Page 189 and 190: Commissioning Assistant31.4. Comple
Page 191 and 192: Commissioning AssistantClick the Po
Page 193 and 194: Commissioning Assistant31.4.7. Chec
Page 195 and 196: Commissioning Assistant31.4.11. Che
Page 197 and 198: Commissioning AssistantSelect a loa
Page 199 and 200: Commissioning AssistantFigure 172.
Page 201 and 202: Commissioning Assistant31.5. Emaili
Page 203 and 204: Error CodesCODE MESSAGE SITUATION20
Page 205 and 206: auto include all data sets ck boxon
Page 208 and 209: database restore for SQL ..........
Page 210 and 211: extract data by set timeon communic
Page 212 and 213: for the MPM screen ................
Page 214 and 215: on discharge s/u ..................
Page 216 and 217: s. serial port screen .............
Page 218 and 219: TAP telephone number ..............
show all

SQL Battery Monitor Data Manager User's Guide - Alber

Create successful ePaper yourself

Delete template?

Save as template?