Classic Shaker Side Table - Popular Woodworking Magazine
Classic Shaker Side Table - Popular Woodworking Magazine Classic Shaker Side Table - Popular Woodworking Magazine
Drawer Primer: Sliding-lid BoxWe discovered that ourdrawer-building techniqueis an ideal method to makesturdy storage boxes.TThis simple box uses the same saw setups andrabbeting techniques for building the drawershown on page 24, and it’s good practice for buildingthe “Simple Shaker End Table” on page 16.However, there are a couple of differences.Unlike a drawer, this box has a sliding lid that’scut using the same joinery we used to make thebottom. We also added a notched piece of woodinside to organize the box’s contents (for us, it’schisels). And there is a small amount of detailinganyone can try: The lid’s bevel and thumb pull aremade with a chisel, rasp and small gouge.To make the box, first choose wood withstraight grain for the sides, front and back, andwood with nice figure for the lid. We built oursfrom a hybrid called Lyptus (see page 32). Dress(joint and plane) your lumber, then cut the partsto finished size, except for the tool holder.Cut the rabbets on your side pieces next, thencut all the grooves. These grooves capture thebox’s bottom and guide the sliding lid. Finally,cut the rabbets on your bottom and lid.Lay out the 11 ⁄ 16"-wide x1 ⁄ 4 "-deep bevel on thelid and shape it using a rasp. Once you get close toyour layout lines, finish the job with a block planeor #120-grit sandpaper and a sanding block.Lay out the location of the thumb pull on thelid. Define all the edges using a straight chisel anda gouge for the curved area. Chop out the straightsection with a chisel and use the gouge to removethe waste. Hand plane or sand all the parts. If youwish to make a tool holder, do so now. To makethe slots for our chisels, we drilled five evenlyspaced 1 ⁄ 2 " holes, then cut out the remaining materialwith a hand saw or a band saw.Dry assemble the box. Once satisfied, glue thesides to the front and back. The bottom floats inits groove and the lid (obviously) slides. Reinforceeach joint with 5 ⁄ 8 " brad nails. We finishedour box with garnet shellac. WM— Christopher Schwarz and Kara GebhartSliding-lid BoxNO. PART SIZES (INCHES) NOTEST W L❑ 1 Front 1 ⁄ 2 2 6 7 ⁄ 81 ⁄ 4 " x 1 ⁄ 4 "groove on bottom❑ 1 Back 1 ⁄ 2 2 1 ⁄ 2 6 7 ⁄ 81 ⁄ 4 " x 1 ⁄ 4 "groove on top and bottom❑ 2 Sides 1 ⁄ 2 2 1 ⁄ 2 15 1 ⁄ 2 "-wide x 1 ⁄ 4 "-deep rabbet on ends;1 ⁄ 4 " x 1 ⁄ 4 "groove on top and bottom❑ 1 Bottom 1 ⁄ 2 6 7 ⁄ 8 14 1 ⁄ 21 ⁄ 4 " x 1 ⁄ 4 " rabbet on all sides❑ 1 Lid 1 ⁄ 2 6 7 ⁄ 8 14 3 ⁄ 41 ⁄ 4 " x 1 ⁄ 4 " rabbet on sides and back❑ 1 Tool holder 1 ⁄ 2 1 1 ⁄ 2 6 3 ⁄ 8 Varies depending on your usagePHOTO BY AL PARRISH28 ■ woodworking magazine Autumn 2004
6®"2ø"ø"‹Bottom hasrabbet onall foursides‹Profileshownwithoutside panel14ø"14"15"14œ"ø"6®"2"©"Plan2" Wide¬" deep at front¬"ø"Profile¬"¬"ø"ø"©"1¬"6µ"2"1ø"Elevation∕See Tool Holder DetailSliding-lid Box¬"ø" Dia.Tool Holder Detailwoodworking-magazine.com ■ 29
- Page 3 and 4: WOODWORKINGM AG A Z I N EAutumn 200
- Page 7 and 8: Avoid Drawknife InjuriesDrawknives
- Page 11 and 12: Mark yourstart and stoppoints on ap
- Page 13 and 14: Sharpen a ChiselHere’s the secret
- Page 15 and 16: “The carpenter is not the best wh
- Page 17 and 18: Bevel-edge ChiselsFFor any one proj
- Page 19 and 20: width. I prefer to use my thickness
- Page 21 and 22: 18"14"11œ"2" ø"œ"œ"3ø"5"œ"1˚
- Page 23 and 24: Notch fitsaround legOnce you cut th
- Page 25 and 26: Now you’re ready to glue up your
- Page 27 and 28: One Setup Cuts All the JointsNow th
- Page 29: Use glue and 5 ⁄ 8 " brads to att
- Page 33 and 34: time measurement starts with the re
- Page 35 and 36: Extras“Believe one who has tried
6®"2ø"ø"‹Bottom hasrabbet onall foursides‹Profileshownwithoutside panel14ø"14"15"14œ"ø"6®"2"©"Plan2" Wide¬" deep at front¬"ø"Profile¬"¬"ø"ø"©"1¬"6µ"2"1ø"Elevation∕See Tool Holder DetailSliding-lid Box¬"ø" Dia.Tool Holder Detailwoodworking-magazine.com ■ 29