TR Instruction Manual - Dover Flexo Electronics, Inc

More documents

Recommendations

Info

1.6 CONFIGURATION CHOICES continued..• Shaft Length. Measured for application and length of roll required. See tables in Section 2.2.1.1 formore information.• Load Ratings. Size 1: 12, 25, 50, 100, 150 lbs. (55, 110, 225, 450, 670 N)Size 2: 12, 25, 50, 100, 200, 400 lbs. (55, 110, 225, 450, 900, 1800 N)• Connector Position. Choices are as follows: 12:00, 1:30, 3:00, 4:30, 6:00 (std.), 7:30, 9:00, 10:301.7 OPTIONS• 90 Degree Grease Fitting (90GF). Grease fitting located at end of roll rather than on OD. For 5" ODor larger rolls.• Counterbore, Drill and Tap (CDT). Shaft ends are counterbored and drilled and tapped.• Drill and Tap (D&T). Drill and tap ends of shaft. Size 1: 5/16-18 (8mm), Size 2: 1/2-13 (12mm)• Environmental Connector (EC). Seals with mating cable electrical connector to protect againstcontact oxidation; especially useful in corrosive environments.• Extended Range Output (XR). Extra sensitive at low tensions. Electronics must have extended rangealso.• Milled Flats (MF). Shaft with milled flats and a through hole at each end.• Non-standard Shaft Extensions (NSE). Shaft extends unequal lengths on ends. Specify lengths.• Oiled Bearings (OB). Oil instead of grease for lubrication. Not recommended by DFE and may voidwarranty.• Steel Roll (SR), or Stainless Steel (SSR) instead of standard aluminum roll.• Wet Environment Cable (WEC). Attached sealed cable for Tension Roll transducers.1.8 ACCESSORIES• Shaft Hangers. Size 1: #140-0005. Size 2: #601-1179 (small), #601-1181 (large)• Shaft Mounting Adapters. Size 1: #601-1201. Size 2: #601-1178• Flanged Shaft Mounting Adapters. Size 1: #601-1203. Size 2: 601-12024
SECTION 2INSTALLATION2.1 DIMENSIONSinches (mm)TENSION ROLL® TRANSDUCERA B C D E F GSIZE 1in. Ø 0.75 * * 0.31 1.12 Ø 3.0 3.0mm Ø 19.05 * * 7.87 28.45 Ø 76.20 76.20SIZE 2in. Ø 1.125 ** ** 0.31 1.50 Ø 4.0 4.0mm Ø 28.58 ** ** 7.87 38.10 Ø 101.60 101.60* Specified at time of order, B - C = 6.0 in. (152.4 mm) ** Specified at time of order, B - C = 8.0 in. (203.2 mm)SHAFT ADAPTER - Single Bolt MountSHAFT ADAPTER - Flange Mount(Size 1: #601-1201, Size 2: #203-0238) (Size 1: #601-1203, Size 2: #601-1202)SHAFT HANGERS FOR TR TRANSDUCERSMODEL A B C D E F G H J KSIZE 1(#140-0005)SIZE 2 - SM(#601-1179)SIZE 2- LG(#601-1181)in. 2.75 2.00 2.12 1.00 1.38 0.75 1.25 0.31 Ø 0.75 0 22mm 69.85 50.80 53.85 25.4 35.05 19.05 31.75 7.87 19.05 5.59in. 4.00 3.00 3.00 1.62 2.12 1.12 1.75 0.43 Ø 1.125 0.34mm 101.60 76.20 76.20 41.15 53.85 28.45 44.45 10.92 28.58 8.63in. 6.00 4.50 4.50 2.62 3.30 1.50 2.50 0.62 Ø 2.00 0.41mm 152.40 114.30 114.30 66.55 83.82 38.10 63.50 15.75 50.80 10.41Figure 3 - DIMENSIONS5
Page 1 and 2: DOVER FLEXO ELECTRONICS, INC.ISO 90
Page 3: TABLE OF CONTENTSSECTION ONE DESCRI
Page 7: 1.4 SPECIFICATIONSExcitation Voltag
Page 11 and 12: Figure 4 - TENSION ZONES3. WRAP ANG
Page 13 and 14: SECTION 3CALIBRATION3.1 INTRODUCTIO
Page 15 and 16: Figure 8 - BEARING LIFE NOMOGRAM11
Page 17 and 18: 4.3 DISASSEMBLY AND REASSEMBLYNOTE:
Page 19 and 20: 15. The disassembly procedure is sl
Page 21 and 22: SECTION 5TROUBLESHOOTING GUIDEThis
Page 23 and 24: SECTION 6REPLACEMENT PARTS(Model TR
Page 25 and 26: Appendix B:Selection of Load Rating
Page 27 and 28: Appendix C:Typical Tensions for Var
Page 29 and 30: DECLARATION OF CONFORMITYWe,Dover F
Page 31 and 32: INDEXAccessories ..................

TR Instruction Manual - Dover Flexo Electronics, Inc

Create successful ePaper yourself

Delete template?

Save as template?