CAN-bus Interface Type ADIF TY03 Toyota ... - speedsignal.de
CAN-bus Interface Type ADIF TY03 Toyota ... - speedsignal.de
CAN-bus Interface Type ADIF TY03 Toyota ... - speedsignal.de
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>speedsignal</strong> GmbH<strong>CAN</strong>-<strong>bus</strong> <strong>Interface</strong><strong>Type</strong> <strong>ADIF</strong> <strong>TY03</strong>for:<strong>Toyota</strong>: Avensis III (2009-)<strong>TY03</strong>/0 (picture similar)universal connexion,length of cable approx. 0,15mpin assignment tableI/OAvailable accessory:long cable,approx. 1mAn interface to connect to vehicles <strong>CAN</strong> <strong>bus</strong>, extracting thespeed signal, and ignition signal.purposecolour ofwireinput ground blacknoteinput battery 12 V red The interface is <strong>de</strong>signed for 12V DC.input <strong>CAN</strong> high yellow At vehicle: see page 2input <strong>CAN</strong> low brown At vehicle: see page 2output*) <strong>speedsignal</strong> whiteoutput*) - green reservedoutput*) ACC/ignition yellow/redoutput*) - orange reservedOutput voltage:square signal 0 .. 12 Volt, approx. 1 Hz per km/houtput 0 V: off (ACC/ignition off)output 12 V: on (ACC/ignition on)Copyright and technichal changes un<strong>de</strong>r reserve.*) The maximum current per output is 180 mA. However, the total current of all outputs together may notexceed 200 mA. Otherwise, the interface could be <strong>de</strong>stroyed. In case a higher current is nee<strong>de</strong>d (ignition,reverse signal) use a relay with coil resistant of min. 75 Ω or min. 150 Ω if two relays are used.<strong>speedsignal</strong> GmbH Tel. +49 (0)8031 23399-0 342<strong>TY03</strong>_R0_enÄußere Oberaustraße 20 Fax. +49 (0)8031 23399-10 issue 09 / 2011D - 83026 Rosenheim Mail: info@<strong>speedsignal</strong>.<strong>de</strong> revision 0www.<strong>speedsignal</strong>.<strong>de</strong> page 1/2
How to connect the <strong>TY03</strong>/0:1. remove car key from lock2. unlink the 8pole Molex MiniFit plug3. connect the single wire ends to the car as given inpin assignment table and double check4. reconnect the interface5. switch on ACC / ignition and check performance of interfaceHow to find the <strong>CAN</strong>-<strong>bus</strong>At the OBD-Connector in the driver footwellOn Board Diagnose connector,below steering wheel column<strong>CAN</strong>-high: Pin 6 black<strong>CAN</strong>-low: Pin 14 whiteOBDfront view, Pin allocation OBD2DisclaimerPlease strictly refer to the automobile manufacturers installation gui<strong>de</strong> lines and terms of warranty when installing electronic units in automobiles. Inform thecustomer(car owner) about the installation and the related risks. To disclaim, it may be useful to contact the automobiles manufacturer or an authorisedworkshop.<strong>speedsignal</strong> GmbH Tel. +49 (0)8031 23399-0 342<strong>TY03</strong>_R0_enÄußere Oberaustraße 20 Fax. +49 (0)8031 23399-10 issue 09 / 2011D - 83026 Rosenheim Mail: info@<strong>speedsignal</strong>.<strong>de</strong> revision 0www.<strong>speedsignal</strong>.<strong>de</strong> page 2/2
Change language