Installation Instructions for Burner Igniter Kit SDE362 ... - Supco

Installation Instructionsfor Burner Igniter Kit SDE362Replaces:Whirlpool 279311 • Robertshaw 41-311 • Maytag LA1021Installation Instructionsfor Burner Igniter Kit SDE362Replaces:Whirlpool 279311 • Robertshaw 41-311 • Maytag LA1021Electrical Shock HazardDisconnect power before servicing.Replace all panels before operating.Failure to do so can result in death or electrical shock.This new igniter may bedifferent from youroriginal igniter.Electrical Shock HazardDisconnect power before servicing.Replace all panels before operating.Failure to do so can result in death or electrical shock.This new igniter may bedifferent from youroriginal igniter.Round ignitorHandle replacement ignitor with care - fragileHandle replacement ignitor with care - fragileRound ignitorNote: Igniter is fragile, Do not remove igniter from this foamprotector by the wires. Hold by the porcelain block and lift up.Note: Igniter is fragile, Do not remove igniter from this foamprotector by the wires. Hold by the porcelain block and lift up.To replace round igniter, follow steps below and refer to Figure 1.1. Unplug dryer or disconnect power.2. Remove lower front toe panel or full front panel, depending on your model.3. Shut off gas supply.4. Remove the brass nut (union) located between the burner and shut off valve.5. Remove the two (2) screws holding the burner base to the cabinet base.6. Keep these two (2) screws, as they will be reused.7. Remove the WHITE (FS2) wire and the BLUE (FS1) wire from the sensor.8. Pull apart the connectors with the BLUE and BLACK wires coming from the gasvalve to the cabinet wiring harness.9. Remove burner assembly from the dryer.To replace round igniter, follow steps below and refer to Figure 1.1. Unplug dryer or disconnect power.2. Remove lower front toe panel or full front panel, depending on your model.3. Shut off gas supply.4. Remove the brass nut (union) located between the burner and shut off valve.5. Remove the two (2) screws holding the burner base to the cabinet base.6. Keep these two (2) screws, as they will be reused.7. Remove the WHITE (FS2) wire and the BLUE (FS1) wire from the sensor.8. Pull apart the connectors with the BLUE and BLACK wires coming from the gasvalve to the cabinet wiring harness.9. Remove burner assembly from the dryer.

10. Cut off BLACK and RED wirese two (2) inches back from bracket.11. Remove and throw away failed igniter and bracket.12. Keep the #10-16 x 1/2 screw, as this will be reused (bracket to burner).13. Take off the insulation from the BLACK and RED wires 3/8 inch from cut end.14. Mount the replacement igniter to the new bracket, using the #8-32 x 5/8 screw/washer packed in kit.15. Mount the replacement igniter and bracket assembly to the burner tube, reusingthe #10-16 x 1/2 screw, mentioned in step 12.16. Cut off flush at the connector on the replacement igniter and take off theinsulation 3/8 inch from end.17. Using one (1) of the wire connectors supplied, put the RED wire from the gasvalve and one (1) of the WHITE wires from the replacement igniter together.18. Using the remaining wire connector supplied, put the BLACK wire from the gasvalve and the remaining WHITE wire from the replacement igniter together.19. Reassemble in reverse order, starting with steps 9, 8, 7, 6, 5, 4, 3, 2, and 1.20. NOTE: Check for gas leaks by using soap on the threads of the brass nut. Do notuse a match or flame of any kind.NOTE: Keep all wires away from the burner flame or igniter when reassemblingthe burner to the cabinet base.21. Plug in dryer or reconnect power.10. Cut off BLACK and RED wirese two (2) inches back from bracket.11. Remove and throw away failed igniter and bracket.12. Keep the #10-16 x 1/2 screw, as this will be reused (bracket to burner).13. Take off the insulation from the BLACK and RED wires 3/8 inch from cut end.14. Mount the replacement igniter to the new bracket, using the #8-32 x 5/8 screw/washer packed in kit.15. Mount the replacement igniter and bracket assembly to the burner tube, reusingthe #10-16 x 1/2 screw, mentioned in step 12.16. Cut off flush at the connector on the replacement igniter and take off theinsulation 3/8 inch from end.17. Using one (1) of the wire connectors supplied, put the RED wire from the gasvalve and one (1) of the WHITE wires from the replacement igniter together.18. Using the remaining wire connector supplied, put the BLACK wire from the gasvalve and the remaining WHITE wire from the replacement igniter together.19. Reassemble in reverse order, starting with steps 9, 8, 7, 6, 5, 4, 3, 2, and 1.20. NOTE: Check for gas leaks by using soap on the threads of the brass nut. Do notuse a match or flame of any kind.NOTE: Keep all wires away from the burner flame or igniter when reassemblingthe burner to the cabinet base.21. Plug in dryer or reconnect power.Replacementignitor & bracket(Steps 14 & 15)Cut off here& strip back(Step 16)Wire connectors(Steps 17 & 18)BlueBlackTo cabinetwiring harness(Step 8)Replacementignitor & bracket(Steps 14 & 15)Cut off here& strip back(Step 16)Wire connectors(Steps 17 & 18)BlueBlackTo cabinetwiring harness(Step 8)To sensor(Step 7)BlueTo sensor(Step 7)BlueRemove & throwaway old ignitor& bracket(Step 11)WhiteGas valve knob(Step 3)Remove & throwaway old ignitor& bracket(Step 11)WhiteGas valve knob(Step 3)Screw(Steps 12 & 15)BlackRedFigure 1Cut off hereand strip back(Steps 10 & 13)Screws(Steps 5 & 6)Brass nut(Step 4)Screw(Steps 12 & 15)BlackRedFigure 1Cut off hereand strip back(Steps 10 & 13)Screws(Steps 5 & 6)Brass nut(Step 4)SEALED UNIT PARTS CO., INC.P.O. Box 21, Allenwood, N.J. 08720www.supco.com • info@supco.comSEALED UNIT PARTS CO., INC.P.O. Box 21, Allenwood, N.J. 08720www.supco.com • info@supco.com