Complete (13 MB) - Chris Alston's Chassisworks

More documents

Recommendations

Info

Use a 5/8-18 tap to chase the threads in theupper A-arm. Clear any debris left in thethreads.Use the same procedure to assemble theupper A-arm as the lower. First, install theballjoint boot into the balljoint housing.Next, apply a layer of anti-seize to theballjoint threads.917703 Page 9
Thread the balljoint in as far as possible byhand.Finish tightening the balljoint with theballjoint wrench until it is seated tight againstthe balljoint housing. Repeat this for thepassenger side upper A-arm.Install the rod ends into the upper A-arms.To provide an initial alignment baseline, thejam nut should be threaded until there is 1-1/16 inches of thread remaining past the jamnut.Page 10 917703
Page 1 and 2: READ ALL INSTRUCTIONS COMPLETELY AN
Page 3 and 4: CONGRATULATIONSYou have purchased t
Page 5 and 6: DISCLAIMER OF WARRANTYPurchasers re
Page 7 and 8: Installing SuspensionNote: The phot
Page 9: The balljoint is then screwed into
Page 13 and 14: Next, chase the threads in the lowe
Page 15 and 16: If you have to remove the lower A-a
Page 17 and 18: Next, install the shock simulator a
Page 20: With the cotter pin installed, use
Page 26 and 27: Install the tie rod end in the stee
Page 28 and 29: First, check and record the camber
Page 30 and 31: Next, set the bar level and tighten
Page 32 and 33: Next, you can final assemble the ti
Page 34 and 35: The caps are held in place with the
Page 36 and 37: With both bushings on the bar, brin
Page 38 and 39: Next, slide the link eyebolt onto t
Page 41 and 42: Screw the spring seat adjuster onto
Page 43 and 44: Install the lower shock spud first.
Page 45 and 46: Add a drop of Loctite to the thread
Page 47 and 48: Pack the outer wheel bearing as you
Page 49 and 50: Next, install the Wilwood brake cal
Page 51 and 52: Use a 3/8” wrench to tighten the
Page 53 and 54: Move the spindle to full right lock
Page 55 and 56: Insert one urethane bushing into ea
Page 57 and 58: These optional stainless steel "spu
Page 59 and 60: Installing Manual Transmission,Clut
Page 61 and 62:
Item 5916-F20-03 Turbo 400, 200-4R,
Page 63 and 64:
After you remove the engine, place
Page 65 and 66:
Use vise grip pliers and an end wre
Page 67 and 68:
Disconnect the clamps that attach t
Page 69 and 70:
Remove the bolts that attach the en
Page 71 and 72:
You need three people; one to opera
Page 73 and 74:
Lower the clip to the ground and pu
Page 75 and 76:
This is the correct orientation of
Page 77 and 78:
Place the top part of the mid and r
Page 79 and 80:
Install the lower half of the rear
Page 81 and 82:
Measure from the lip on the rocker
Page 83 and 84:
Attach the stock hook rod to the pa
Page 85 and 86:
Install two 1/2” self-locking set
Page 87 and 88:
Slide the splined end of the u-join
Page 89 and 90:
This is a photo of the completed in
Page 91 and 92:
Drill a 1/8” hole centered in the
Page 93 and 94:
Drill the remaining rivet holes sta
Page 95 and 96:
Installing HeadersSpecial Note: We
Page 97 and 98:
Installing SubframeConnectorsThe su
Page 99 and 100:
Once you have all the bolts removed
Page 101 and 102:
The spring clips can be just as tri
Page 103 and 104:
Slide a 3/8 inch flat washer over t
Page 105 and 106:
Page 104 917703
show all

Complete (13 MB) - Chris Alston's Chassisworks

Create successful ePaper yourself

Delete template?

Save as template?