[Instruction] Contents

More documents

Recommendations

Info

• Locations and application of the card number storageFB-DAP saves RF card numbers within sensing distance into two places in PLC. The places and application aredescribed as follows:4、Fixed in R3835~R3839(totaling 5 registers):During operation, M1910 shall be controlled.Card numberformatR3835 N1 N2R3836 × × × ×R3837 × × × ×R3838 × × × ×R3839 × × × ×N1:DAP number 1~16(i.e. 1H~10H)N2:52H(R:read-only card) or 57H(W:readable/writable card)R3836~R3839 store 16 0~F card numbersApplication:Only in monitoring (or8/16 soft keys) mode (non-FUN functions) and the RF card in sensing distance,FB-DAP(−AR or −BR)will send the RF card number together with DAP number to PLC R3835~R3839. Inmode 0 of function 14 (RF CARD MODE), all the client needs to do is compare the card number. If it isOK, only set M1910 to 1 and then DAP will indicate “OK”, or “ERROR”. When the RF card is out of sensingdistance, DAP will pop up “NEXT” and clear the content of PLC R3838~R3839 to 0, which meansavailable for another RF card. In mode 1 of function 14, as soon as DAP reads a card number, it will saveit to R3835~R3839 with a beep. After the RF card exits, the 5 registers remain unchanged.Applicable occasions:Where one set or multiple sets are connected but RF cards are not used frequently, the program to beapplied will be a lot easier. But in the event of a card number read from different DAPs at the same time, itwill be difficult for PLC to identify the information correctly.5、Preset D2860~D2939 (16 differently-located DAP take on 5 registers individually, i.e. 80 registers in all, but thelocations can be changed through function 15) control one point of M1880~M1895 separately when in use.Card numberformatCard numberformatCard numberformatCard numberformatD2860 N1 N2 D2865 N1 N2 D2870 N1 N2 D2935 N1 N2D2861 × × × × D2866 × × × × D2871 × × × × D2936 × × × ×D2862 × × × × D2867 × × × × D2872 × × × × ……….. D2937 × × × ×D2863 × × × × D2868 × × × × D2873 × × × × D2938 × × × ×D2864 × × × × D2869 × × × × D3974 × × × × D2939 × × × ×No. 1⇓M1880No. 2⇓M1881No. 3⇓M1882No. 16⇓M1895Application measures:The application measures are all described as the above-mentioned but that the storage places of cardnumbers and corresponding contacts for control are different. For example, in mode 0 of function 14, fromNo. 2 DAP sensing to the RF card, now no. 2 will send same card numbers to two different places inR3835~R3839 and D2865~D2869 (the content of the other registers remains unchanged), and all theclient needs to do is control M1881 for the DAP to display “OK” or “ERROR”. After the RF card exits, thecontent of the 10 registers R3835~R3839 and D2865~D2869 will be cleared to 0 (but remainsunchanged in mode 1).Applicable occasions:When several DAPs are connected, the RF card can be read in from different DAPs and each DAP has itsindependent card numbers storage places and control points so that no PLC misjudgment case occurs, butthe programming will be more troublesome.※ If you do not want R3835~R3839 to display a card number value, you can use the Ladder program to fill inthese registers with other fixed values.Appendix -10
1.7 Special message display functionIn general monitoring mode and soft key mode (16 KEYS or 8 KEYS), the user can configure the DAP to displayevery kind of message under some circumstances, and the two-line display on the LCD can be controlledseparately to simultaneously display different messages. Every message is 1~511 words and numbers (ASCII code)long, in which a maximum of 16 variables (if variables with 32-digit are not used, then it can use up to 25) can beincluded. When a message has more than 16 words, the message will be displaced left for display, in which themoving speed or pause time can be configured flexibly.1.7.1 Message display applicationThe FB-DAPB(R) can be connected up to 16 sets (Number 1~16). Each DAP not only can display differentmessages individually but make all the DAPs connected display the same message simultaneously. If you go to aspecial contact (R3780~M3813) set by Enable, the DAP will display the message ASCII Code) indicated by thecorresponding indication register (R3780~M3813). The content of the indication register is the start register ofmessages, i.e. start of ASCII Code. The indication register content can be changed anytime in order to change anddisplay different messages.The following is a list of corresponding special contacts and indication registers when each DAP isdisplaying a message for control.Number ofa messagedisplayedSpecialcontactLCD line 1 LCD line 2IndicationregisterSpecialcontactIndicationregister1~16 M1800 R3780 M1801 R37811 M1802 R3782 M1803 R37832 M1804 R3784 M1805 R37853 M1806 R3786 M1807 R37874 M1808 R3788 M1809 R37895 M1810 R3790 M1811 R37916 M1812 R3792 M1813 R37937 M1814 R3794 M1815 R37958 M1816 R3796 M1817 R37979 M1818 R3798 M1819 R379910 M1820 R3800 M1821 R380111 M1822 R3802 M1823 R3803※ The start register of a messageindicated by an indication registermeans:0~8070:indicating R0~R807010000~13070:indicating D0~D3070※ Special contacts M1800 and M1801have a priority display function.※ M1911 can control an alarm buzzerwhether to sound or not. If M1911=0(preset), it shall be activated.12 M1824 R3804 M1825 R380513 M1826 R3806 M1827 R380714 M1828 R3808 M1829 R380915 M1830 R3810 M1831 R381116 M1832 R3812 M1833 R3813〈Example〉Assume M1803 from 0→1, R3783=100Result:Line 2 of No. 1 of the LCD will display messages in ASCII Code with R100 start.〈Example〉 Assume M1828 from 0→1, R3808=10000Result:Line 1 of No. 14 of the LCD will display messages in ASCII Code with D0 start.〈Example〉 Assume M1801 from 0→1, R3781=0Result:Line 2 of all the DAPs will display messages in ASCII Code with R0 start.Appendix -11
Page 6 and 7:
Conventional Ladder DiagramPLC Ladd
Page 8 and 9:
Input processing (Reading thestatus
Page 10 and 11:
We must energize the coil of relay
Page 12 and 13:
Network: Network is a circuit repre
Page 15 and 16:
1.5 The De-Composition of a Network
Page 18 and 19:
• When a single element or a seri
Page 20 and 21:
MEMO
Page 22 and 23:
2.2 Digital and Register Allocation
Page 24 and 25:
Relay No. Function Description3. Pu
Page 26 and 27:
Relay No. Function DescriptionM1965
Page 28 and 29:
2.4 Special Registers DetailsRegist
Page 30 and 31:
Register No. Function DescriptionR4
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Register No. Function DescriptionD4
Page 40 and 41:
Instruction Operand Symbol Function
Page 42 and 43:
FUNNo.NameOperandDerivativeInstruct
Page 44 and 45:
FUNNo.NameOperandDerivativeinstruct
Page 46 and 47:
• Ramp Function InstructionsFUNNo
Page 48 and 49:
MEMO
Page 50 and 51:
※For the relays marked with a ‘
Page 52 and 53:
FUN7 is the UDCTR function. While r
Page 54 and 55:
X0X1Node ANode BIncerseInversediffe
Page 56 and 57:
All input controls of the function
Page 58 and 59:
• The names and functions of the
Page 60 and 61:
5.1.4 Functions Output (FO)The “F
Page 62 and 63:
Indirect addressing program example
Page 64 and 65:
5.3.2 The Coding of Numeric Numbers
Page 66 and 67:
(2). 0.5 = (-1) 0 * 2 ( 01111110 )
Page 68 and 69:
While all FBs-PLC numerical operati
Page 70 and 71:
Basic Function InstructionT TIMER T
Page 72 and 73:
Basic Function InstructionT TIMER T
Page 74 and 75:
Basic Function InstructionCCOUNTER(
Page 76 and 77:
Basic Function InstructionSET D PSy
Page 78 and 79:
Basic Function InstructionRST D PSy
Page 80 and 81:
Basic Function InstructionFUN 0MCSy
Page 82 and 83:
Basic Function InstructionFUN 1MCES
Page 84 and 85:
Basic Function InstructionFUN 2SKPS
Page 86 and 87:
Basic Function InstructionFUN 4DIFU
Page 88 and 89:
Basic Function InstructionFUN 6 D P
Page 90 and 91:
Basic Function InstructionFUN 7 DUD
Page 92 and 93:
Basic Function InstructionFUN 9 D P
Page 94 and 95:
Basic Function InstructionFUN 11 D
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Advanced Function InstructionFUN22
Page 110 and 111:
Advanced Function InstructionFUN 24
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Advanced Function InstructionFUN32A
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Advanced Function InstructionEND PR
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Advanced Function InstructionFUN89/
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Advanced Function InstructionTable
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231: Advanced Function InstructionFUN 15
Page 232 and 233: Advanced Function InstructionFUN160
Page 234 and 235: Advanced Function InstructionFUN201
Page 242 and 243: Advance Function InstructionFUN 208
Page 248 and 249: MEMO
Page 250 and 251: 8.2 Basic Formation of Step Ladder
Page 252 and 253: . Single CycleM1924X0• When step
Page 254 and 255: ●STP Sxxx : S20≦Sxxx≦S999(Dis
Page 256 and 257: 【Description】: 1. When ON, the
Page 258 and 259: ●STPEND :(Displayed in WinProladd
Page 260 and 261: Example 1WinProladderFP-07M1924STP
Page 262 and 263: Example 3WinProladderFP-07M1924STP
Page 264 and 265: WinProladderFP-07M1924STP S0X1X2X0S
Page 266 and 267: WinProladderM1924TO S0X1STP S0SET Y
Page 268 and 269: ●Pedestrian Crossing Lights Contr
Page 270 and 271: 8.6 Syntax Check Error Codes for St
Page 272 and 273: 1.1 Profile112798716外徑 4ψ×4
Page 274 and 275: 〝H〞 indicates hexadecimal↓
Page 276 and 277: 1.5.2 FUN function description• F
Page 278 and 279: 【Example】Assume definition as R
Page 282 and 283: 1.7.2 The Information formats of me
show all

[Instruction] Contents

Create successful ePaper yourself

Delete template?

Save as template?