VITODENS 200 WB2A - Heatingspares247.com

More documents

Recommendations

Info

3 Installation RequirementsPositionMinimum SpacingLHorizontally from a terminal on same wall300mm12inMAdjacent to opening300mm12inNBelow carport<strong>200</strong>mm8inOFrom adjacent wall300mm12inPFrom adjacent opening window1000mm40inQFrom another terminal600mm24inRMinimum height300mm12inFigure 3/A: Flue Termination Position12
3 Installation Requirements3.3 Flue Terminal LocationDetailed recommendations for flue installation are given in BS 5440:1. The followingnotes are for general guidance.a) The boiler MUST be installed so that the terminal is exposed to external air.b) It is important that the position of the terminal allows free passage of airacross it at all times.c) It is ESSENTIAL TO ENSURE that products of combustion discharging fromthe terminal cannot re-enter the building or any other adjacent building,through ventilators, windows, doors, other sources of natural air infiltrationor forced ventilation / air conditioning.d) The minimum acceptable dimensions from the terminal to obstructions andventilation openings are specified in Figure 3/A.(BS 5440 Part 1)e) If the terminal discharges into a pathway or passageway check thatcombustion products will not cause nuisance and that the terminal will notobstruct the passageway.f) Where the lowest part of the terminal is fitted less than 2m (78in) aboveground, above a balcony or above a flat roof to which people have access,the terminal MUST be protected by a purpose designed guard. (Available asan optional extra).g) Where the terminal is fitted within 850mm (34in) of a plastic or paintedgutter, or 450mm (18in) of painted eaves, an aluminium shield at least750mm long must be fitted to the underside of the painted surface.h) The air inlet / flue outlet duct MUST NOT be closer that 25mm (1in) tocombustible material.i) In certain weather conditions the terminal may emit a plume of steam. Thisis normal but positions where this would cause a nuisance should beavoided.13
Page 1 and 2: VITODENS 200 WB2AINSTALLATION & SER
Page 3 and 4: 1 General Information1.1 Appliance
Page 5 and 6: 2 Technical Specifications2.2 Gener
Page 8 and 9: 2 Technical Specifications2.6 Hydra
Page 10 and 11: 3 Installation Requirements3.1 Stat
Page 14 and 15: 3 Installation Requirements3.4 Vent
Page 16 and 17: 3 Installation RequirementsFigure 3
Page 18 and 19: 3 Installation Requirements3.5 Cent
Page 20 and 21: 3 Installation Requirements3.7 Gas
Page 22 and 23: 4 Installation ProcedureFigure 4/A:
Page 24 and 25: 4 Installation Procedure4.2.2 Fitti
Page 27 and 28: 4 Installation ProcedureFigure 4/E:
Page 29 and 30: 4 Installation Procedure4.7.2 Verti
Page 31 and 32: 4 Installation Procedure4.8.2 Verti
Page 33 and 34: 4 Installation Procedure4.9.1 Elect
Page 35 and 36: 4 Installation Procedure4.11 Conden
Page 37 and 38: 5 Commissioning and Testing5.1 Fill
Page 39 and 40: 5 Commissioning and Testing5.3 Vent
Page 41 and 42: 5 Commissioning and Testing5.6 Comm
Page 43 and 44: 5 Commissioning and Testing5.9 Fina
Page 45 and 46: 6 Routine Servicing6.1 Routine Serv
Page 47 and 48: 6 Routine Servicing6.4 Combustion C
Page 49 and 50: 6 Routine Servicing6.8 Re-commissio
Page 51 and 52: 8 Fault FindingIt is the law that a
Page 53 and 54: 9 Replacement of PartsBefore commen
Page 55 and 56: 9 Replacement of Parts9.3 Burnera)
Page 57 and 58: 9 Replacement of Parts9.7 Air Press
Page 59 and 60: 9 Replacement of Parts9.10 Limit Th
Page 61 and 62: 9 Replacement of Parts9.13 CH Therm
Page 63 and 64:
9 Replacement of Parts9.16 DHW Heat
Page 65 and 66:
9 Replacement of Parts9.17 DHW Flow
Page 67 and 68:
9 Replacement of Parts9.21 Pressure
Page 69 and 70:
9 Replacement of Parts9.23 Expansio
Page 71 and 72:
10 Replacement Parts001 Quick Actin
Page 73 and 74:
10 Replacement Parts004 Temperature
Page 75:
11 Index6 . . . . . . . . . . . . .
show all

VITODENS 200 WB2A - Heatingspares247.com

Create successful ePaper yourself

Delete template?

Save as template?