Select PlantStruxure reference architectures? - Schneider Electric ...
Select PlantStruxure reference architectures? - Schneider Electric ... Select PlantStruxure reference architectures? - Schneider Electric ...
WARNINGWARNING indicates a potentially hazardous situation which, if not avoided, can result in deathor serious injury.Failure to follow these instructions can cause death, serious injury or equipmentdamage.CAUTIONCAUTION indicates a potentially hazardous situation which, if not avoided, can result in minoror moderate injury.Failure to follow these instructions can result in injury or equipment damage.Before You BeginNOTICENOTICE is used to address practices not related to physical injury.Failure to follow these instructions can result in equipment damage.Note: Electrical equipment should be installed, operated, serviced, and maintained only byqualified personnel. No responsibility is assumed by Schneider Electric for any consequencesarising out of the use of this material.A qualified person is one who has skills and knowledge related to the construction, operation andinstallation of electrical equipment, and has received safety training to recognize and avoid thehazards involved.This automation equipment and related software is used to control a variety of industrialprocesses. The type or model of automation equipment suitable for each application will varydepending on factors such as the control function required, degree of protection required,production methods, unusual conditions and government regulations etc. In some applicationsmore than one processor may be required when backup redundancy is needed.Only the user can be aware of all the conditions and factors present during setup, operation andmaintenance of the solution. Therefore only the user can determine the automation equipmentand the related safeties and interlocks which can be properly used. When selecting automationand control equipment and related software for a particular application, the user should refer to© 2012 Schneider Electric All Rights Reserved4
the applicable local and national standards and regulations. The National Safety Council’sAccident Prevention Manual also provides much useful information.Ensure that appropriate safeties and mechanical/electrical interlocks protection have beeninstalled and are operational before placing the equipment into service. All mechanical/electricalinterlocks and safeties protection must be coordinated with the related automation equipment andsoftware programming.Note: Coordination of safeties and mechanical/electrical interlocks protection is outside the scopeof this document.START UP AND TESTFollowing installation but before using electrical control and automation equipment for regularoperation, the system should be given a start up test by qualified personnel to verify the correctoperation of the equipment. It is important that arrangements for such a check be made and thatenough time is allowed to perform complete and satisfactory testing.WARNINGEQUIPMENT OPERATION HAZARDFollow all start up tests as recommended in the equipment documentation.Store all equipment documentation for future reference.Software testing must be done in both simulated and real environments.Failure to follow these instructions can cause death, serious injury or equipmentdamage.Verify that the completed system is free from all short circuits and grounds, except those groundsinstalled according to local regulations (according to the National Electrical Code in the USA, forexample). If high-potential voltage testing is necessary, follow recommendations in the equipmentdocumentation to prevent accidental equipment damage.Before energizing equipment:Remove tools, meters, and debris from equipmentClose the equipment enclosure doorRemove ground from incoming power linesPerform all start-up tests recommended by the manufacturer© 2012 Schneider Electric All Rights Reserved5
- Page 3: Important InformationNoticePeople r
- Page 7 and 8: The architecture described in this
- Page 9 and 10: The STN CollectionThe implementatio
- Page 11 and 12: Table of Contents1. Introduction 13
- Page 13 and 14: 1 - Introduction1. Introduction1.1.
- Page 16 and 17: 1 - Introduction1.4. PlantStruxure
- Page 18 and 19: 2 - Selection2.2. PlantStruxure tec
- Page 20 and 21: 2 - Selection2.3. PlantStruxure fun
- Page 22 and 23: 2 - Selection© 2012 Schneider Elec
- Page 24 and 25: 3 - Global ref. archi.Two types of
- Page 26 and 27: 3 - Global ref. archi.3.3.2. Centra
- Page 28 and 29: 3 - Global ref. archi.3.4.2. Modula
- Page 30 and 31: 3 - Global ref. archi.Functional ax
- Page 32 and 33: 3 - Global ref. archi.3.6. PlantStr
- Page 34 and 35: 4 - Control room ref. archi.4.2. Pl
- Page 36 and 37: 4 - Control room ref. archi.Histori
- Page 38 and 39: 4 - Control room ref. archi.4.5. Co
- Page 40 and 41: Communication5 - Func. unit ref. ar
- Page 42 and 43: 5 - Func. unit ref. archi.VSD Modbu
- Page 44 and 45: 5 - Func. unit ref. archi.EthernetB
- Page 46 and 47: 5 - Func. unit ref. archi.The three
- Page 48 and 49: 5 - Func. unit ref. archi.60 instru
- Page 50 and 51: 5 - Func. unit ref. archi.Modicon S
- Page 52 and 53: 5 - Func. unit ref. archi.5.4.2. Fu
the applicable local and national standards and regulations. The National Safety Council’sAccident Prevention Manual also provides much useful information.Ensure that appropriate safeties and mechanical/electrical interlocks protection have beeninstalled and are operational before placing the equipment into service. All mechanical/electricalinterlocks and safeties protection must be coordinated with the related automation equipment andsoftware programming.Note: Coordination of safeties and mechanical/electrical interlocks protection is outside the scopeof this document.START UP AND TESTFollowing installation but before using electrical control and automation equipment for regularoperation, the system should be given a start up test by qualified personnel to verify the correctoperation of the equipment. It is important that arrangements for such a check be made and thatenough time is allowed to perform complete and satisfactory testing.WARNINGEQUIPMENT OPERATION HAZARDFollow all start up tests as recommended in the equipment documentation.Store all equipment documentation for future <strong>reference</strong>.Software testing must be done in both simulated and real environments.Failure to follow these instructions can cause death, serious injury or equipmentdamage.Verify that the completed system is free from all short circuits and grounds, except those groundsinstalled according to local regulations (according to the National <strong>Electric</strong>al Code in the USA, forexample). If high-potential voltage testing is necessary, follow recommendations in the equipmentdocumentation to prevent accidental equipment damage.Before energizing equipment:Remove tools, meters, and debris from equipmentClose the equipment enclosure doorRemove ground from incoming power linesPerform all start-up tests recommended by the manufacturer© 2012 <strong>Schneider</strong> <strong>Electric</strong> All Rights Reserved5