WAREMA Mobile System® WMS Central transmitter
WAREMA Mobile System® WMS Central transmitter WAREMA Mobile System® WMS Central transmitter
Getting startedWAREMAWMS Central transmitter6.5 Operating example:Operating products6.5.1 Operating a productdirectlyThere are several ways to operate a product (a channel) with the WMS Centraltransmitter. You can operate the product directly, preselect positions orrecall a scene.The product responds directly to the press of a button on the WMS Centraltransmitter.Main menu Products Product typeButtonAction/resultIn the main menu, press the function button repeatedly untilthe selection cursor is on the [Products] line.Press the ok button.The [Select product type] menu opens.Using the function buttons, select the product type that youwould like to operate.Press the ok button.All products of this type are displayed.The buttons that are relevant to the particular product areactivated on the right.Operate the product using the function buttons. In the followingexample, the product is an external venetian blind:Short: The slats tilt upLong: The product moves upThe product stopsShort: The slats tilt downLong: The product moves downShort: The product moves to the stored comfort positionLong: The comfort position for the product is storedNOTE A detailed overview of the operating functionsof the various product types can be found inChapter 4.3 on page 20.The status display indicates the transmission after everyoperating step:GREEN: The central transmitter is transmittingRED: The command is not confirmed (e.g. the receiver isoutside of the transmission range)36We reserve the right to carry out improvements890405_0•en•01.11.2009
Getting started6.5.2 Operating a product bypreselecting the positionThe position is preset. The product does not move to the set value until thevalue is enabled.Main menu Products Product type ChannelButtonAction/resultIn the main menu, press the function button repeatedly untilthe selection cursor is on the [Products] line.Press the ok button.The [Select product type] menu opens.Using the function buttons, select the product type that youwould like to operate.Press the ok button.All channels of this type are displayed.Using the function buttons, select the channel that you wouldlike to operate.Press the ok button.All parameters of this channel are displayed. In the exampleshown here of the external venetian blind, the position andslat angle can be changed.Use the selection cursor to select a line whose entry youwish to change (in the example: slat angle).Use the arrow buttons on the right to adjust the parameter tothe desired valueConfirm the changed value with OK.The new value is now sent to the actuator and the product ispositioned accordingly.The status display indicates the transmission process:GREEN: The central transmitter is transmittingRED: The command is not confirmed (e.g. the receiver isoutside of the transmission range)890405_0•en•01.11.2009 We reserve the right to carry out improvements 37
- Page 1 and 2: WAREMA Mobile System ®WMS Central
- Page 3 and 4: ContentsContents1 Legal notes......
- Page 5 and 6: Contents9.2.4 Loading the factory s
- Page 7 and 8: IntroductionCongratulations on choo
- Page 9 and 10: Safety instructions2.2 Intended use
- Page 11 and 12: Safety instructions2.5 Working safe
- Page 13 and 14: CommissioningCAUTIOThe plastic feet
- Page 15 and 16: Introduction4 IntroductionThe WMS C
- Page 17 and 18: Introduction4.2 Menu elementsAn ove
- Page 19 and 20: Introduction4.2.2 Product type disp
- Page 21 and 22: IntroductionProduct typeAwning with
- Page 23 and 24: Introduction4.4.5 FavouritesAny des
- Page 25 and 26: Menu structure4.5 Sleep modeThe WMS
- Page 27 and 28: Getting started5.2 ProductsCopy cha
- Page 29 and 30: Getting started5.4 System (part 2)L
- Page 31 and 32: Getting startedGCurrent settings of
- Page 33 and 34: Getting started6.3 Example for oper
- Page 35: Getting started6.4 Operating exampl
- Page 39 and 40: Favourites7 FavouritesYou will oper
- Page 41 and 42: FavouritesButtonAction/resultOperat
- Page 43 and 44: Favourites7.1.3 Operating products
- Page 45 and 46: Favourites7.3 Managing favouritesTo
- Page 47 and 48: Favourites7.3.2 Selecting an iconTo
- Page 49 and 50: Favourites7.3.4 Allocating a channe
- Page 51 and 52: Favourites7.3.6 Deleting a favourit
- Page 53 and 54: FavouritesButtonAction/resultUsing
- Page 55 and 56: FavouritesButtonAction/resultUsing
- Page 57 and 58: FavouritesButtonAction/resultUsing
- Page 59 and 60: Products8.1 Operating theproducts8.
- Page 61 and 62: Products8.1.3 Operating products by
- Page 63 and 64: ProductsButtonAction/resultUsing th
- Page 65 and 66: ProductsButtonAction/resultUsing th
- Page 67 and 68: ProductsButtonAction/resultUsing th
- Page 69 and 70: ProductsButtonAction/resultUsing th
- Page 71 and 72: ProductsButtonAction/resultUsing th
- Page 73 and 74: ProductsButtonAction/resultUsing th
- Page 75 and 76: ProductsButtonAction/resultUsing th
- Page 77 and 78: System9.1 ProductsNOTEVia the [Prod
- Page 79 and 80: System9.1.2 Calling up channelinfor
- Page 81 and 82: System9.1.3 SettingsThis menu gives
- Page 83 and 84: System9.1.3.1 Basic functionsMain m
- Page 85 and 86: SystemMenu itemSwitch-off delaySett
Getting started6.5.2 Operating a product bypreselecting the positionThe position is preset. The product does not move to the set value until thevalue is enabled.Main menu Products Product type ChannelButtonAction/resultIn the main menu, press the function button repeatedly untilthe selection cursor is on the [Products] line.Press the ok button.The [Select product type] menu opens.Using the function buttons, select the product type that youwould like to operate.Press the ok button.All channels of this type are displayed.Using the function buttons, select the channel that you wouldlike to operate.Press the ok button.All parameters of this channel are displayed. In the exampleshown here of the external venetian blind, the position andslat angle can be changed.Use the selection cursor to select a line whose entry youwish to change (in the example: slat angle).Use the arrow buttons on the right to adjust the parameter tothe desired valueConfirm the changed value with OK.The new value is now sent to the actuator and the product ispositioned accordingly.The status display indicates the transmission process:GREEN: The central <strong>transmitter</strong> is transmittingRED: The command is not confirmed (e.g. the receiver isoutside of the transmission range)890405_0•en•01.11.2009 We reserve the right to carry out improvements 37