WAREMA Mobile System® WMS Central transmitter
WAREMA Mobile System® WMS Central transmitter WAREMA Mobile System® WMS Central transmitter
SystemWAREMAWMS Central transmitterButtonAction/resultEnter the serial number of the device.(For entering texts, see also Chapter 6.4 on page 35).Press the button to learn out the device.The following message appears.Press the ok button and check whether all devices wave. Youcan press the ok button as often as necessary.Leave the menu using the button when you are sure thatall network devices confirmed the delete command by waving.The Commissioning menu opens again.106We reserve the right to carry out improvements890405_0•en•01.11.2009
System9.2.4 Loading the factorysettingsThis function can be used to reset the central transmitter to the factory settingswhen needed. After this, extensive commissioning work will be to setup the central transmitter again.CAUTIOThis deletes the central transmitter from the network. If there are no furthertransmitters in the network, the central transmitter cannot be added to thenetwork. In this case, the WMS network needs to be fully re-commissioned.Proceed as follows to load the factory settings.Main menu System Commissioning Load factory settingButtonAction/resultIn the main menu, select the [System] menu and press ok.The [System] menu opens.Select the [Commissioning] menu here and press ok.The [Commissioning] menu opens.Using the selection cursor, select the[Load factory settings] menu item.Call up the function with ok.The following menu is displayed.Press the ok button to reset the central transmitter.The central transmitter restarts completely after a fewseconds. Wait for the start procedure to finish and the mainmenu to be displayed again.890405_0•en•01.11.2009 We reserve the right to carry out improvements 107
- Page 55 and 56: FavouritesButtonAction/resultUsing
- Page 57 and 58: FavouritesButtonAction/resultUsing
- Page 59 and 60: Products8.1 Operating theproducts8.
- Page 61 and 62: Products8.1.3 Operating products by
- Page 63 and 64: ProductsButtonAction/resultUsing th
- Page 65 and 66: ProductsButtonAction/resultUsing th
- Page 67 and 68: ProductsButtonAction/resultUsing th
- Page 69 and 70: ProductsButtonAction/resultUsing th
- Page 71 and 72: ProductsButtonAction/resultUsing th
- Page 73 and 74: ProductsButtonAction/resultUsing th
- Page 75 and 76: ProductsButtonAction/resultUsing th
- Page 77 and 78: System9.1 ProductsNOTEVia the [Prod
- Page 79 and 80: System9.1.2 Calling up channelinfor
- Page 81 and 82: System9.1.3 SettingsThis menu gives
- Page 83 and 84: System9.1.3.1 Basic functionsMain m
- Page 85 and 86: SystemMenu itemSwitch-off delaySett
- Page 87 and 88: SystemMenu itemSlat angle, warm -18
- Page 89 and 90: System9.1.3.12 ScenesMain menu Syst
- Page 91 and 92: System9.1.3.15 Sensor allocationMai
- Page 93 and 94: System9.1.4 Move command faultsFor
- Page 95 and 96: System9.1.6 Actuators in the channe
- Page 97 and 98: SystembuttonAction/resultUsing the
- Page 99 and 100: SystemNOTEIf you wish to learn in a
- Page 101 and 102: System9.2.2 Learning hand-heldtrans
- Page 103 and 104: SystemButtonAction/resultUsing the
- Page 105: System9.2.3 Learning out actuators/
- Page 109 and 110: SystemButtonAction/resultLeave the
- Page 111 and 112: SystembuttonAction/resultPress the
- Page 113 and 114: System9.3.2 Setting the date and ti
- Page 115 and 116: System9.3.3 Adjusting the backgroun
- Page 117 and 118: System9.4 Specialist dealerNOTEIn t
- Page 119 and 120: System9.4.3 Changing the specialist
- Page 121 and 122: Technical data10 Technical dataWARE
- Page 123 and 124: Notes890405_0•en•01.11.2009 We
System9.2.4 Loading the factorysettingsThis function can be used to reset the central <strong>transmitter</strong> to the factory settingswhen needed. After this, extensive commissioning work will be to setup the central <strong>transmitter</strong> again.CAUTIOThis deletes the central <strong>transmitter</strong> from the network. If there are no further<strong>transmitter</strong>s in the network, the central <strong>transmitter</strong> cannot be added to thenetwork. In this case, the <strong>WMS</strong> network needs to be fully re-commissioned.Proceed as follows to load the factory settings.Main menu System Commissioning Load factory settingButtonAction/resultIn the main menu, select the [System] menu and press ok.The [System] menu opens.Select the [Commissioning] menu here and press ok.The [Commissioning] menu opens.Using the selection cursor, select the[Load factory settings] menu item.Call up the function with ok.The following menu is displayed.Press the ok button to reset the central <strong>transmitter</strong>.The central <strong>transmitter</strong> restarts completely after a fewseconds. Wait for the start procedure to finish and the mainmenu to be displayed again.890405_0•en•01.11.2009 We reserve the right to carry out improvements 107