SkyView - Dynon Avionics
SkyView - Dynon Avionics SkyView - Dynon Avionics
Basic SkyView Display OperationUpgrade System Software...–Use this wizard to update software on your SkyViewsystem.Export System Settings...–Use this wizard to export the settings on your SkyView systemto a USB flash drive.Export Data Log...–Datalogging is for internal use only. User-datalogging is notsupported at this time.Load Files...–Use this wizard to load files such as settings or configuration files or deletefiles from the USB flash drive.System Setup MenuThis menu contains links to the following menus and pages:Network Setup–Enter this menu to configure your SkyView network or to check onnetwork status (i.e., display important SkyView module information).Aircraft Information–Enter this page to record important information regarding youraircraft. Specifically, enter the tail number of your aircraft–it is used to create uniqueSkyView configuration files. It is also used for other purposes.Measurement Units–Enter this page to configure displayed units (e.g., feet or meters).Time–Enter this page to set the time zone offset from Zulu/GMT time.ARINC-429–Enter this page to set up ARINC-429 devices connected to SV-ARINC-429modules.Local Display Setup MenuThis menu contains links to the following pages and menus:Installed Databases–This page shows the various databases that are installed on thedisplay and their respective versions.Display Hardware Information–This page contains important hardware statusinformation such as the serial number of your display and the voltage of the attachedbackup battery. Reference the Returning SkyView Components to Service after RepairSection of this guide for more information about the Display Hardware InformationPage.Serial Port Setup–Enter this menu to configure the five general purpose serial ports onthe display.Brightness Setup–Enter this page to choose between manual, automatic, or externalscreen backlight control. Manual screen backlight control is managed by the user in theDIM Menu with the DEC-, INC+, and FULL buttons. Automatic screen backlight control ismanaged by a default dimming profile in the display. A compatible external controlsignal is required for external backlight control. Reference the Brightness Setup Sectionfor more information.Top Bar Setup–Enter this page to configure the top bar on the SkyView display's screen.3-10 SkyView System Installation Guide - Revision J
Basic SkyView Display OperationGPS Fix Status–This page shows fix quality information for the GPS source that is beingused as the active position source for SkyView’s moving map and synthetic vision. Notethat this does not show information about other GPS sources that may be available forHSI and backup position use.License–Enter this page to display the status of software products that can be purchasedand licensed to add features to SkyView. This page is also the place where license codescan be redeemed to activate features on your SkyView System.PFD Setup MenuThis menu contains links to the following pages:ADAHRS Source Selection–This page is a list of all configured SkyView ADAHRS modulesand their respective statuses. Also use it to select which ADAHRS module is the PFD’sprimary source of data.Flight Angle Pitch Adjust–This page allows you to adjust the displayed pitch of the plane.Airspeed Limitations–Enter this menu to configure the V-speeds and specify optimalflight parameters such as best angle of climb speed, best rate of climb speed, andmaneuvering speed.Vertical Speed Scale–Enter this page to configure the vertical speed tape's scale.G Meter–Enter this page to configure G values that will cause the G Meter to beautomatically displayed when exceeded; to set the yellow/red cautionary color rangesof the G meter; and whether or not the max/min recorded Gs are reset at each SkyViewboot-up.Flight Path Marker–Enter this page to enable/disable display of the flight path marker.Extreme Pitch Warning–Enter this page to enable/disable display of the extreme pitchwarning indicators.Angle of Attack–Enter this page to enable/disable display of the Angle of Attackindicator.EMS Setup MenuThis menu contains links to the following wizards and menu:Engine Information–Enter this wizard to record important information regarding theengine in your aircraft such as engine type and horsepower. The user-enteredinformation here is used to calculate quantities such as % power and special operatinglimitations.Sensor Input Mapping...–Enter this wizard to map engine and environmental sensors toSV-EMS-220 pins. Reference the EMS Sensor Input Mapping Section of this guide forinstructions on how to navigate and use this menu to map sensors.Screen Layout Editor–Enter this wizard to configure the placement and style of theonscreen EMS gauges on EMS pages. Reference the EMS Screen Layout Editor Section ofthis guide for instructions on how to use this wizard.SkyView System Installation Guide - Revision J 3-11
- Page 3 and 4: Contact InformationDynon Avionics,
- Page 5 and 6: Revision Revision Date DescriptionS
- Page 7: Revision Revision Date DescriptionA
- Page 12 and 13: Table of ContentsEthernet Connectio
- Page 14 and 15: Table of ContentsVP-X SkyView Displ
- Page 16 and 17: IntroductionAbout this GuideIn the
- Page 18 and 19: System PlanningTable 4 contains phy
- Page 20 and 21: System PlanningSV-ADAHRS-200 and SV
- Page 22 and 23: System PlanningThere are no module-
- Page 24 and 25: System PlanningServos (SV32, SV42,
- Page 26 and 27: System Planningon any one of them.
- Page 28 and 29: System PlanningFigure 5-SkyView Sys
- Page 30 and 31: System PlanningHSI RequirementsThe
- Page 32 and 33: Basic SkyView Display OperationDisp
- Page 34 and 35: Basic SkyView Display OperationA bu
- Page 36: Basic SkyView Display OperationBasi
- Page 43: Basic SkyView Display OperationServ
- Page 46 and 47: SV-D700 / SV-D1000 Installation and
- Page 48 and 49: SV-D700 / SV-D1000 Installation and
- Page 50 and 51: SV-D700 / SV-D1000 Installation and
- Page 52 and 53: SV-D700 / SV-D1000 Installation and
- Page 54 and 55: SV-D700 / SV-D1000 Installation and
- Page 56 and 57: SV-D700 / SV-D1000 Installation and
- Page 58 and 59: SV-D700 / SV-D1000 Installation and
- Page 60 and 61: SV-D700 / SV-D1000 Installation and
- Page 62 and 63: SV-D700 / SV-D1000 Installation and
- Page 64 and 65: SV-D700 / SV-D1000 Installation and
- Page 66 and 67: SV-ADAHRS-20X Installation and Conf
- Page 68 and 69: SV-ADAHRS-20X Installation and Conf
- Page 71 and 72: SV-ADAHRS-20X Installation and Conf
- Page 73: SV-ADAHRS-20X Installation and Conf
- Page 76 and 77: SV-ADAHRS-20X Installation and Conf
- Page 78 and 79: SV-ADAHRS-20X Installation and Conf
- Page 81 and 82: 7. SV-EMS-220 Installation and Conf
- Page 83 and 84: SkyView Network ConnectionSV-EMS-22
- Page 85 and 86: SV-EMS-220 Installation and Configu
Basic <strong>SkyView</strong> Display OperationGPS Fix Status–This page shows fix quality information for the GPS source that is beingused as the active position source for <strong>SkyView</strong>’s moving map and synthetic vision. Notethat this does not show information about other GPS sources that may be available forHSI and backup position use.License–Enter this page to display the status of software products that can be purchasedand licensed to add features to <strong>SkyView</strong>. This page is also the place where license codescan be redeemed to activate features on your <strong>SkyView</strong> System.PFD Setup MenuThis menu contains links to the following pages:ADAHRS Source Selection–This page is a list of all configured <strong>SkyView</strong> ADAHRS modulesand their respective statuses. Also use it to select which ADAHRS module is the PFD’sprimary source of data.Flight Angle Pitch Adjust–This page allows you to adjust the displayed pitch of the plane.Airspeed Limitations–Enter this menu to configure the V-speeds and specify optimalflight parameters such as best angle of climb speed, best rate of climb speed, andmaneuvering speed.Vertical Speed Scale–Enter this page to configure the vertical speed tape's scale.G Meter–Enter this page to configure G values that will cause the G Meter to beautomatically displayed when exceeded; to set the yellow/red cautionary color rangesof the G meter; and whether or not the max/min recorded Gs are reset at each <strong>SkyView</strong>boot-up.Flight Path Marker–Enter this page to enable/disable display of the flight path marker.Extreme Pitch Warning–Enter this page to enable/disable display of the extreme pitchwarning indicators.Angle of Attack–Enter this page to enable/disable display of the Angle of Attackindicator.EMS Setup MenuThis menu contains links to the following wizards and menu:Engine Information–Enter this wizard to record important information regarding theengine in your aircraft such as engine type and horsepower. The user-enteredinformation here is used to calculate quantities such as % power and special operatinglimitations.Sensor Input Mapping...–Enter this wizard to map engine and environmental sensors toSV-EMS-220 pins. Reference the EMS Sensor Input Mapping Section of this guide forinstructions on how to navigate and use this menu to map sensors.Screen Layout Editor–Enter this wizard to configure the placement and style of theonscreen EMS gauges on EMS pages. Reference the EMS Screen Layout Editor Section ofthis guide for instructions on how to use this wizard.<strong>SkyView</strong> System Installation Guide - Revision J 3-11