SkyView - Dynon Avionics

More documents

Recommendations

Info

Accessory Installation and ConfigurationHeater Controller WiringFigure 79–Heated AOA/Pitot Probe Wiring OverviewBefore making the connections to your Heated AOA/Pitot Probe and controller, refer toAppendix C: Wiring and Electrical Connections. The table below provides general14-4 <strong>SkyView</strong> System Installation Guide - Revision J
Accessory Installation and Configurationrecommendations for wire gauge choice, given wiring run length. It assumes 10 amps ofcurrent.Probe to Controller WiringRun length (in feet) Gauge0 to 7 18 AWG7 to 9 16 AWG10 to 16 14 AWG17 to 24 12 AWG25 to 40 10 AWGTable 42–From FAA AC 43.13-1B, page 11-30As mentioned above, it is preferable that the heater controller box be mounted near enough tothe probe that 5 wires between the controller and probe can be connected without extension.The three mating pairs of colored wires–terminated with Fastons–are used to carry the currentto the heating element in the probe. The 2 white wires are for temperature measurement, andcan be small. If you have mounted the heater controller near the probe and do not need toextend the wires between the two, simply plug each wire on the controller into itscorresponding like-colored wire from the probe.If you do need to extend the wires between the probe and the controller, use therecommended wire size (see Table 42) for your run length. Since extending the wire runsrequires that you cut the connectors off the 5 wires between the probe and controller, splicethe extension wires between the probe and controller using butt splices or other similarlysecure method. The white wires are not polarity-dependent. Additionally, as the white wires donot carry any significant current, you may extend them with 26 AWG or larger for any runlength.Controller Power WiringThree wires–colored red, black, and white–exit the controller for connection to your electricalsystem. Power (between 10 and 15 volts DC) is fed to the controller via the red and black wires.The maximum current draw of the heated pitot controller/probe is 10 amps. You must routeyour own appropriately-sized wires to where the heater controller is mounted. Both power andground lines should be able to handle 10 amps with minimal voltage drop, as recommended inTable 42.The red wire should be connected through a pilot-accessible switch to the main power sourcein the aircraft (limited to 15 volts DC). The switch allows you to manually turn the heatercontroller on and off, depending on the situation. Install a 15 amp fuse at any point along thepower line to the heater controller. Remember that even when the controller is powered on, itonly heats the probe the amount necessary to maintain temperature.The black wire should be permanently connected to ground. Cutting power to the heatercontroller should occur via the red power line, not the black ground line.<strong>SkyView</strong> System Installation Guide - Revision J 14-5
Page 3 and 4:
Contact InformationDynon Avionics,
Page 5 and 6:
Revision Revision Date DescriptionS
Page 7:
Revision Revision Date DescriptionA
Page 12 and 13:
Table of ContentsEthernet Connectio
Page 14 and 15:
Table of ContentsVP-X SkyView Displ
Page 16 and 17:
IntroductionAbout this GuideIn the
Page 18 and 19:
System PlanningTable 4 contains phy
Page 20 and 21:
System PlanningSV-ADAHRS-200 and SV
Page 22 and 23:
System PlanningThere are no module-
Page 24 and 25:
System PlanningServos (SV32, SV42,
Page 26 and 27:
System Planningon any one of them.
Page 28 and 29:
System PlanningFigure 5-SkyView Sys
Page 30 and 31:
System PlanningHSI RequirementsThe
Page 32 and 33:
Basic SkyView Display OperationDisp
Page 34 and 35:
Basic SkyView Display OperationA bu
Page 36:
Basic SkyView Display OperationBasi
Page 41 and 42:
Basic SkyView Display OperationGPS
Page 43:
Basic SkyView Display OperationServ
Page 46 and 47:
SV-D700 / SV-D1000 Installation and
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
SV-ADAHRS-20X Installation and Conf
Page 68 and 69:
Page 71 and 72:
Page 73:
Page 76 and 77:
Page 78 and 79:
Page 81 and 82:
7. SV-EMS-220 Installation and Conf
Page 83 and 84:
SkyView Network ConnectionSV-EMS-22
Page 85 and 86:
SV-EMS-220 Installation and Configu
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Tools and Equipment RequiredSV-EMS-
Page 107 and 108:
Page 109 and 110:
Note that you may need access to th
Page 111 and 112:
Fuel Pressure SensorSV-EMS-220 Inst
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
EMS Sensor Input MappingSV-EMS-220
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Example Contact Sensor SetupAssume
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
8. SV-GPS-250 Installation and Conf
Page 137 and 138:
SV-GPS-250 Installation and Configu
Page 139 and 140:
9. SV-BAT-320 InstallationThis chap
Page 141:
Battery Status CheckSV-BAT-320 Inst
Page 144 and 145:
Autopilot Servo Installation, Confi
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157: Autopilot Servo Installation, Confi
Page 173 and 174: 11. SV-XPNDR-26X Installation, Conf
Page 175 and 176: SV-XPNDR-26X Installation, Configur
Page 179 and 180: Power/Ground InputSV-XPNDR-26X Inst
Page 181 and 182: Serial GPS Position Input (Future U
Page 187 and 188: Altitude Encoder CalibrationSV-XPND
Page 189 and 190: 12. SV-ARINC-429 Installation and C
Page 191 and 192: SV-ARINC-429 Installation and Confi
Page 193 and 194: ARINC Device ConnectionsSV-ARINC-42
Page 197: SV-ARINC-429 Installation and Confi
Page 204 and 205: Accessory Installation and Configur
Page 217 and 218: 15. Appendix A: Maintenance and Tro
Page 219 and 220: Appendix A: Maintenance and Trouble
Page 221 and 222: Display Input VoltageThe display's
Page 223 and 224: Appendix A: Maintenance and Trouble
Page 225: Appendix A: Maintenance and Trouble
Page 228 and 229: Appendix B: SpecificationsSkyView C
Page 230 and 231: Appendix B: SpecificationsSV-XPNDR-
Page 232 and 233: Appendix C: Wiring and Electrical C
Page 249 and 250: 18. Appendix D: SV-EMS-220 Sensor I
Page 251 and 252: 19. Appendix E: Serial Data OutputA
Page 253 and 254: ` Appendix E: Serial Data OutputPar
Page 255 and 256: ` Appendix E: Serial Data OutputDYN
Page 257 and 258:
` Appendix E: Serial Data OutputPar
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
` Appendix E: Serial Data Output!11
show all

SkyView - Dynon Avionics

Create successful ePaper yourself

Delete template?

Save as template?