SkyView - Dynon Avionics

More documents

Recommendations

Info

SV-XPNDR-26X Installation, Configuration, and TestingThe following figure shows a typical installation, as viewed from the wiring side of the DB25connector:Figure 67 - Typical SV-XPNDR-26X Connections (Rear Pin Insertion View)The following figure shows all possible connections, as viewed from the wiring side of the DB25connector:Figure 68 - All Possible SV-XPNDR-26X Connections (Rear Pin Insertion View)Note that pins 1 / 2, and pins 12 / 13 must be connected to each other as depictedabove via your wiring harness. They are not shorted internally.11-6 SkyView System Installation Guide - Revision J
Power/Ground InputSV-XPNDR-26X Installation, Configuration, and TestingThe power supply can be 11-33 Volts DC; no voltage adjustment is required. 20 AWG wire issufficient for wire runs up to 50’ for this application. Use a 3 or 5 Amp fuse or circuit breaker forpower supply protection to the SV-XPNDR-26X. Note that none of SkyView’s voltage outputscan provide a sufficient amount of power to power the transponder module. The transpondermust be connected to aircraft power.It is always good practice to use more than one ground path in an installation. With only onewire there may be only a single grounding path for the transponder, controller and antenna.This can allow static electricity to build up and damage your SkyView display(s). Ensuring thatthe mounting tray is grounded provides an adequate alternative ground path to protect againstsuch events. This is particularly important when the transponder is mounted on a nonconductingsurface, such as a composite structure, where the mounting tray is often notgrounded. Therefore, make sure that the mounting tray is grounded in addition to having theground wire connected as depicted above.Note: The transponder power input is not protected against reversed powerconnections. Reversing the power and ground inputs to the transponder willdestroy it. Check wiring before applying power.Pin 1/2 and 12/13 LoopbacksPins 1/2, and pins 12/13 must be connected to each other as depicted in the figures above.Serial RX/TXAll communication between the SV-XPNDR-26X module and SkyView is accomplished via asingle bidirectional a serial connection. To accomplish this:Choose an unused serial port on each display to connect the SV-XPNDR-26X to. Notethat both the TX and RX sides of the serial port are needed, and both the RX and TX linesmust be connected to all displays in parallel. It is helpful, but not required, to choose thesame numerical serial port on each display. This lets you configure each display’s serialports identically.Connect the SV-XPNDR-26X TX wire (pin 7) to the SkyView serial RX of your choosing. Ifyou have multiple displays, the transponder TX wire must be connected to a serial RXwire on each display.Connect the SV-XPNDR-26X RX wire (pin 5) to the SkyView serial TX of your choosing. Ifyou have multiple displays, the transponder RX wire must be connected to a serial TXwire on each display.Record the SkyView serial port that you have chosen on each display as you will need toconfigure it later for use with the transponder.SkyView System Installation Guide - Revision J 11-7
Page 3 and 4:
Contact InformationDynon Avionics,
Page 5 and 6:
Revision Revision Date DescriptionS
Page 7:
Revision Revision Date DescriptionA
Page 12 and 13:
Table of ContentsEthernet Connectio
Page 14 and 15:
Table of ContentsVP-X SkyView Displ
Page 16 and 17:
IntroductionAbout this GuideIn the
Page 18 and 19:
System PlanningTable 4 contains phy
Page 20 and 21:
System PlanningSV-ADAHRS-200 and SV
Page 22 and 23:
System PlanningThere are no module-
Page 24 and 25:
System PlanningServos (SV32, SV42,
Page 26 and 27:
System Planningon any one of them.
Page 28 and 29:
System PlanningFigure 5-SkyView Sys
Page 30 and 31:
System PlanningHSI RequirementsThe
Page 32 and 33:
Basic SkyView Display OperationDisp
Page 34 and 35:
Basic SkyView Display OperationA bu
Page 36:
Basic SkyView Display OperationBasi
Page 41 and 42:
Basic SkyView Display OperationGPS
Page 43:
Basic SkyView Display OperationServ
Page 46 and 47:
SV-D700 / SV-D1000 Installation and
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
SV-ADAHRS-20X Installation and Conf
Page 68 and 69:
Page 71 and 72:
Page 73:
Page 76 and 77:
Page 78 and 79:
Page 81 and 82:
7. SV-EMS-220 Installation and Conf
Page 83 and 84:
SkyView Network ConnectionSV-EMS-22
Page 85 and 86:
SV-EMS-220 Installation and Configu
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Tools and Equipment RequiredSV-EMS-
Page 107 and 108:
Page 109 and 110:
Note that you may need access to th
Page 111 and 112:
Fuel Pressure SensorSV-EMS-220 Inst
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
EMS Sensor Input MappingSV-EMS-220
Page 125 and 126:
Page 127 and 128: SV-EMS-220 Installation and Configu
Page 129 and 130: Example Contact Sensor SetupAssume
Page 135 and 136: 8. SV-GPS-250 Installation and Conf
Page 137 and 138: SV-GPS-250 Installation and Configu
Page 139 and 140: 9. SV-BAT-320 InstallationThis chap
Page 141: Battery Status CheckSV-BAT-320 Inst
Page 144 and 145: Autopilot Servo Installation, Confi
Page 173 and 174: 11. SV-XPNDR-26X Installation, Conf
Page 175 and 176: SV-XPNDR-26X Installation, Configur
Page 177: SV-XPNDR-26X Installation, Configur
Page 181 and 182: Serial GPS Position Input (Future U
Page 187 and 188: Altitude Encoder CalibrationSV-XPND
Page 189 and 190: 12. SV-ARINC-429 Installation and C
Page 191 and 192: SV-ARINC-429 Installation and Confi
Page 193 and 194: ARINC Device ConnectionsSV-ARINC-42
Page 197: SV-ARINC-429 Installation and Confi
Page 204 and 205: Accessory Installation and Configur
Page 217 and 218: 15. Appendix A: Maintenance and Tro
Page 219 and 220: Appendix A: Maintenance and Trouble
Page 221 and 222: Display Input VoltageThe display's
Page 223 and 224: Appendix A: Maintenance and Trouble
Page 225: Appendix A: Maintenance and Trouble
Page 228 and 229:
Appendix B: SpecificationsSkyView C
Page 230 and 231:
Appendix B: SpecificationsSV-XPNDR-
Page 232 and 233:
Appendix C: Wiring and Electrical C
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 249 and 250:
18. Appendix D: SV-EMS-220 Sensor I
Page 251 and 252:
19. Appendix E: Serial Data OutputA
Page 253 and 254:
` Appendix E: Serial Data OutputPar
Page 255 and 256:
` Appendix E: Serial Data OutputDYN
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
` Appendix E: Serial Data Output!11
show all

SkyView - Dynon Avionics

Create successful ePaper yourself

Delete template?

Save as template?