SkyView - Dynon Avionics

More documents

Recommendations

Info

SV-XPNDR-26X Installation, Configuration, and TestingPhysical InstallationMounting Tray and SV-XPNDR-26X DimensionsFigure 64 - SV-XPNDR-26X Mounting Tray DimensionsFigure 65 - SV-XPNDR-26X Dimensions with Mounting Tray (dimensions in millimeters)Installation InstructionsThe SV-XPNDR-26X Mode S transponder is designed to be mounted in any convenient locationin the cockpit, the cabin, or an avionics bay.The following installation procedure should be followed, remembering to allow adequate spacefor installation of cables and connectors.Select a position in the aircraft that is not too close to any high external heat source.(The SV-XPNDR-26X is not a significant heat source itself and does not need to be keptaway from other devices for this reason).Avoid sharp bends and placing the cables too near to the aircraft control cables.11-2 SkyView System Installation Guide - Revision J
SV-XPNDR-26X Installation, Configuration, and TestingSecure the mounting tray to the aircraft via the three (3) mounting holes in the tray.The tray should be mounted to a flat surface - it is important that the tray is supportedat the dimples as well as the three mounting points.Put the SV-XPNDR-26X transponder into the secured mounting tray by hooking theconnector end under the lip on the tray.Lock the SV-XPNDR-26X transponder into the mounting tray by clipping the retainingwire over the lugs on the opposite end.Additional items you will require, but which are not in the SV-XPNDR-26X package, include:Antenna and fixing hardware. The SV-XPNDR-26X is compatible with transponderantennas commonly available.Cables and male TNC connector. You need to supply and fabricate all required cables.Guidance on cable types is given below.Mounting hardware: To secure the transponder tray to the airframe you will need atleast 3 flat head screws and three self-locking nuts. If the aircraft does not have existingmounting provisions you may need to fabricate additional brackets to support thetransponder tray.Electrical ConnectionsHarness ConstructionBecause the SV-XPNDR-26X can be mounted in a variety of locations, the harness lengthrequirements will vary from airplane to airplane. Therefore, Dynon Avionics does not supplypre-manufactured harnesses for the SV-XPNDR-26X. Instead, your SV-XPNDR-26X shipped withenough connectors and pins to generate a wide variety of harness configurations. Refer to thesections below for detailed wiring information.If you do not own a D-sub machined-pin crimping tool, they can be obtained for under $50 frommany retailers. See http://wiki.dynonavionics.com/Tools_not_supplied_by_Dynon for knownsources of these products. You may also find it helpful to own a pin insertion/extraction tool aswell.Additional harness construction and wiring information can be found in Appendix C: Wiring andElectrical Connections.The SV-XPNDR-26X has a single DB25 female connector which provides the data and powerinputs to the transponder. A single TNC coaxial connector attaches to the antenna.SkyView System Installation Guide - Revision J 11-3
Page 3 and 4:
Contact InformationDynon Avionics,
Page 5 and 6:
Revision Revision Date DescriptionS
Page 7:
Revision Revision Date DescriptionA
Page 12 and 13:
Table of ContentsEthernet Connectio
Page 14 and 15:
Table of ContentsVP-X SkyView Displ
Page 16 and 17:
IntroductionAbout this GuideIn the
Page 18 and 19:
System PlanningTable 4 contains phy
Page 20 and 21:
System PlanningSV-ADAHRS-200 and SV
Page 22 and 23:
System PlanningThere are no module-
Page 24 and 25:
System PlanningServos (SV32, SV42,
Page 26 and 27:
System Planningon any one of them.
Page 28 and 29:
System PlanningFigure 5-SkyView Sys
Page 30 and 31:
System PlanningHSI RequirementsThe
Page 32 and 33:
Basic SkyView Display OperationDisp
Page 34 and 35:
Basic SkyView Display OperationA bu
Page 36:
Basic SkyView Display OperationBasi
Page 41 and 42:
Basic SkyView Display OperationGPS
Page 43:
Basic SkyView Display OperationServ
Page 46 and 47:
SV-D700 / SV-D1000 Installation and
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
SV-ADAHRS-20X Installation and Conf
Page 68 and 69:
Page 71 and 72:
Page 73:
Page 76 and 77:
Page 78 and 79:
Page 81 and 82:
7. SV-EMS-220 Installation and Conf
Page 83 and 84:
SkyView Network ConnectionSV-EMS-22
Page 85 and 86:
SV-EMS-220 Installation and Configu
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Tools and Equipment RequiredSV-EMS-
Page 107 and 108:
Page 109 and 110:
Note that you may need access to th
Page 111 and 112:
Fuel Pressure SensorSV-EMS-220 Inst
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124: EMS Sensor Input MappingSV-EMS-220
Page 125 and 126: SV-EMS-220 Installation and Configu
Page 129 and 130: Example Contact Sensor SetupAssume
Page 135 and 136: 8. SV-GPS-250 Installation and Conf
Page 137 and 138: SV-GPS-250 Installation and Configu
Page 139 and 140: 9. SV-BAT-320 InstallationThis chap
Page 141: Battery Status CheckSV-BAT-320 Inst
Page 144 and 145: Autopilot Servo Installation, Confi
Page 173: 11. SV-XPNDR-26X Installation, Conf
Page 177 and 178: SV-XPNDR-26X Installation, Configur
Page 179 and 180: Power/Ground InputSV-XPNDR-26X Inst
Page 181 and 182: Serial GPS Position Input (Future U
Page 187 and 188: Altitude Encoder CalibrationSV-XPND
Page 189 and 190: 12. SV-ARINC-429 Installation and C
Page 191 and 192: SV-ARINC-429 Installation and Confi
Page 193 and 194: ARINC Device ConnectionsSV-ARINC-42
Page 197: SV-ARINC-429 Installation and Confi
Page 204 and 205: Accessory Installation and Configur
Page 217 and 218: 15. Appendix A: Maintenance and Tro
Page 219 and 220: Appendix A: Maintenance and Trouble
Page 221 and 222: Display Input VoltageThe display's
Page 223 and 224: Appendix A: Maintenance and Trouble
Page 225:
Appendix A: Maintenance and Trouble
Page 228 and 229:
Appendix B: SpecificationsSkyView C
Page 230 and 231:
Appendix B: SpecificationsSV-XPNDR-
Page 232 and 233:
Appendix C: Wiring and Electrical C
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 249 and 250:
18. Appendix D: SV-EMS-220 Sensor I
Page 251 and 252:
19. Appendix E: Serial Data OutputA
Page 253 and 254:
` Appendix E: Serial Data OutputPar
Page 255 and 256:
` Appendix E: Serial Data OutputDYN
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
` Appendix E: Serial Data Output!11
show all

SkyView - Dynon Avionics

Create successful ePaper yourself

Delete template?

Save as template?