SkyView - Dynon Avionics

More documents

Recommendations

Info

Autopilot Servo Installation, Configuration, and CalibrationThe servo arm must not rotate even near to the point called OVER CENTER, thepoint at which the primary aircraft control would “lock up”. Over center happenswhen the angle between the servo arm and the attached push rod becomes sogreat that the control system cannot drive against the servo arm. To protectagainst this possibility, a Range of Motion Limiting Bracket is supplied with eachDynon Avionics servo. These brackets are drilled so that they can be mounted atdifferent angles as required (18° intervals). The brackets are supplied for theprotection of the pilot, and we recommend that the Range of Motion LimitingBracket be installed to ensure that an OVER CENTER condition cannot occur.During normal servo operation, the Range of Motion Limiting Bracket should neverbe used. It is only intended for use as a safety mechanism in the SkyView Autopilotsystem.Once a suitable mounting point for each servo has been determined, the next step is tofabricate a mount for the servo to attach to the aircraft. Generally this will be a bracket made ofsheet metal or corner stock. Dynon recommends using 6061 T6 aluminum with a minimumthickness of 0.050” for the best balance of strength to weight. When fabricating a mountingbracket, refer to the servo dimensions below. Be sure to leave ample room for the arm andattached linkage to move through a complete range of motion without interference.In normal operation, Dynon’s servos can reach temperatures that can be veryuncomfortable to, and perhaps cause burns to unprotected skin. Thus, servosshould be mounted in an area, or in such a manner to prevent accidental skincontact. If mounting the servo in an exposed area is necessary, a shroud should beinstalled (that doesn’t restrict ventilation) that protects against accidental skincontact with the servos.10-4 SkyView System Installation Guide - Revision J
Autopilot Servo Installation, Configuration, and CalibrationPush-Pull Servo DimensionsUse the following dimensions (in inches) for reference when planning and implementing yourinstallation.Long-arm variants(not needed in mostinstallations) havelinkage mount holesat 1.5”, 1.75”, and2.0”LSV32 2.17”SV42 3.10”SV52 4.02”Weight2 lb3 lb4 lbSkyView System Installation Guide - Revision J 10-5
Page 3 and 4:
Contact InformationDynon Avionics,
Page 5 and 6:
Revision Revision Date DescriptionS
Page 7:
Revision Revision Date DescriptionA
Page 12 and 13:
Table of ContentsEthernet Connectio
Page 14 and 15:
Table of ContentsVP-X SkyView Displ
Page 16 and 17:
IntroductionAbout this GuideIn the
Page 18 and 19:
System PlanningTable 4 contains phy
Page 20 and 21:
System PlanningSV-ADAHRS-200 and SV
Page 22 and 23:
System PlanningThere are no module-
Page 24 and 25:
System PlanningServos (SV32, SV42,
Page 26 and 27:
System Planningon any one of them.
Page 28 and 29:
System PlanningFigure 5-SkyView Sys
Page 30 and 31:
System PlanningHSI RequirementsThe
Page 32 and 33:
Basic SkyView Display OperationDisp
Page 34 and 35:
Basic SkyView Display OperationA bu
Page 36:
Basic SkyView Display OperationBasi
Page 41 and 42:
Basic SkyView Display OperationGPS
Page 43:
Basic SkyView Display OperationServ
Page 46 and 47:
SV-D700 / SV-D1000 Installation and
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
SV-ADAHRS-20X Installation and Conf
Page 68 and 69:
Page 71 and 72:
Page 73:
Page 76 and 77:
Page 78 and 79:
Page 81 and 82:
7. SV-EMS-220 Installation and Conf
Page 83 and 84:
SkyView Network ConnectionSV-EMS-22
Page 85 and 86:
SV-EMS-220 Installation and Configu
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96: SV-EMS-220 Installation and Configu
Page 105 and 106: Tools and Equipment RequiredSV-EMS-
Page 109 and 110: Note that you may need access to th
Page 111 and 112: Fuel Pressure SensorSV-EMS-220 Inst
Page 123 and 124: EMS Sensor Input MappingSV-EMS-220
Page 129 and 130: Example Contact Sensor SetupAssume
Page 135 and 136: 8. SV-GPS-250 Installation and Conf
Page 137 and 138: SV-GPS-250 Installation and Configu
Page 139 and 140: 9. SV-BAT-320 InstallationThis chap
Page 141: Battery Status CheckSV-BAT-320 Inst
Page 144 and 145: Autopilot Servo Installation, Confi
Page 173 and 174: 11. SV-XPNDR-26X Installation, Conf
Page 175 and 176: SV-XPNDR-26X Installation, Configur
Page 179 and 180: Power/Ground InputSV-XPNDR-26X Inst
Page 181 and 182: Serial GPS Position Input (Future U
Page 187 and 188: Altitude Encoder CalibrationSV-XPND
Page 189 and 190: 12. SV-ARINC-429 Installation and C
Page 191 and 192: SV-ARINC-429 Installation and Confi
Page 193 and 194: ARINC Device ConnectionsSV-ARINC-42
Page 195 and 196: SV-ARINC-429 Installation and Confi
Page 197:
SV-ARINC-429 Installation and Confi
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Accessory Installation and Configur
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 217 and 218:
15. Appendix A: Maintenance and Tro
Page 219 and 220:
Appendix A: Maintenance and Trouble
Page 221 and 222:
Display Input VoltageThe display's
Page 223 and 224:
Page 225:
Page 228 and 229:
Appendix B: SpecificationsSkyView C
Page 230 and 231:
Appendix B: SpecificationsSV-XPNDR-
Page 232 and 233:
Appendix C: Wiring and Electrical C
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 249 and 250:
18. Appendix D: SV-EMS-220 Sensor I
Page 251 and 252:
19. Appendix E: Serial Data OutputA
Page 253 and 254:
` Appendix E: Serial Data OutputPar
Page 255 and 256:
` Appendix E: Serial Data OutputDYN
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
` Appendix E: Serial Data Output!11
show all

SkyView - Dynon Avionics

Create successful ePaper yourself

Delete template?

Save as template?